Home › Drivetrain ยท AXLE AND DIFFERENTIAL › FRONT DIFFERENTIAL CARRIER ASSEMBLY (for 4WD)

FRONT DIFFERENTIAL CARRIER ASSEMBLY (for 4WD) > DISASSEMBLY

for Preparation Click here



1. REMOVE AUTOMATIC DISCONNECTING DIFFERENTIAL ACTUATOR


    C159257
  1. Remove the 4 bolts.

  1. Using a hammer handle, remove the actuator.



2. REMOVE FRONT DIFFERENTIAL TUBE ASSEMBLY


    C159258
  1. Remove the 4 bolts.

  1. Using a plastic-faced hammer, remove the differential tube.



3. REMOVE DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL


    C159259E01
  1. Using SST, tap out the oil seal.

    SST
    09308-00010  



4. REMOVE DIFFERENTIAL SIDE GEAR INTER SHAFT SUB-ASSEMBLY


    C159260E02
  1. Using SST, remove the side gear inter shaft.

    SST
    09350-20015   (09369-20040)
    09950-40011   (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09955-04011, 09957-04010, 09958-04011)
    Text in Illustration 
    *a
    Turn
    *b
    Hold

  1. Remove the snap ring from the side gear inter shaft.



5. REMOVE FRONT DRIVE PINION COMPANION FLANGE FRONT NUT


    C159261E01
  1. Using SST and a hammer, unstake the nut.

    SST
    09930-00010  



    C159262E01
  1. Using SST to hold the companion, remove the nut.

    SST
    09330-00021   (09330-00030)



6. REMOVE FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY


    C159263E05
  1. Using SST, remove the companion flange from the differential carrier.

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03020)
    Text in Illustration 
    *a
    Turn
    *b
    Hold



7. REMOVE FRONT DIFFERENTIAL CARRIER OIL SEAL


    C159264E01
  1. Using SST, remove the oil seal.

    SST
    09308-10010  



8. REMOVE FRONT DIFFERENTIAL DRIVE PINION OIL SLINGER


9. REMOVE FRONT DIFFERENTIAL CROSS SHAFT BEARING RETAINER


    C160133E01
  1. Remove the bolts B and front differential front support assembly LH.

  1. Remove the bolts A.

  1. Using a plastic-faced hammer, tap out the bearing retainer.



10. REMOVE DIFFERENTIAL CASE ASSEMBLY
  1. Remove the differential case from the differential carrier.



11. REMOVE DIFFERENTIAL DRIVE PINION


    C159434E03
  1. Set the differential carrier to an overhaul stand as shown in the illustration.
    Text in Illustration 
    *a
    Block

  1. Using a press, press out the drive pinion.

    NOTICE:
    Do not drop the drive pinion.



12. REMOVE FRONT DRIVE PINION FRONT RADIAL BALL BEARING
  1. Remove the bearing (inner race) from the differential carrier.



13. REMOVE FRONT DIFFERENTIAL DRIVE PINION BEARING SPACER


14. REMOVE FRONT DIFFERENTIAL BREATHER PLUG OIL DEFLECTOR


    C159446
  1. Remove the 2 bolts and oil deflector.



15. REMOVE FRONT DIFFERENTIAL UNION


    C159447
  1. Remove the front differential union from the differential carrier.



16. REMOVE FRONT DRIVE PINION REAR TAPERED ROLLER BEARING


    C294202E02
  1. Using SST and a press, press out the bearing (inner race).

    SST
    09950-00020  
    If the drive gear or ring gear is damaged, replace them as a set.



17. REMOVE FRONT DRIVE PINION REAR TAPERED ROLLER BEARING


    C159337
  1. Using a brass bar and hammer, tap out the bearing (outer race) and washer.



18. REMOVE FRONT DRIVE PINION FRONT RADIAL BALL BEARING


    C159338E01
  1. Using SST and hammer, tap out the bearing (outer race).

    SST
    09950-70010   (09951-07100)
    09950-60010   (09951-00450)
    09950-60020   (09951-00710, 09952-06010)



19. REMOVE FRONT DIFFERENTIAL CASE BEARING

HINT:
  1. Measure the plate washer and note its thickness.
  2. Tag the bearing outer races to show the location for reassembly.



    C159266E04
  1. Using SST and a press, press out the bearing (outer race) and plate washer from the bearing retainer.

    SST
    09950-60020   (09951-00680)
    09950-70010   (09951-07150)
    Text in Illustration 
    *1
    Plate Washer



    C159267E04
  1. Using SST and a press, press out the outer race and plate washer from the differential carrier.

    SST
    09950-60020   (09951-00680)
    09950-70010   (09951-07150)
    Text in Illustration 
    *1
    Plate Washer



20. REMOVE DIFFERENTIAL RING GEAR


    C159243E03
  1. Place matchmarks on the ring gear and differential case.
    Text in Illustration 
    *a
    Matchmark

  1. Remove the 12 bolts.

  1. Using a plastic-faced hammer, tap on the ring gear to separate it from the differential case.



21. REMOVE FRONT DIFFERENTIAL CASE BEARING


    C159244E01
  1. Using SST, remove the 2 bearings (inner race).

    SST
    09950-60010   (09951-00550)
    09950-40011   (09951-04020, 09952-04010, 09953-04030, 09954-04010, 09955-04061, 09957-04010, 09958-04011)

    HINT:
    Fix the claws of SST into the notch in the differential case assembly.



22. DISASSEMBLE DIFFERENTIAL CASE


    C159245
  1. Using a pin punch and hammer, tap out the straight pin.

  1. Remove these parts from the differential case assembly.

    1. 2 differential side gears

    2. 2 differential side gear thrust washers

    3. Differential pinion shaft

    4. 2 differential pinion gears

    5. 2 differential pinion gear thrust washers



23. INSPECT DIFFERENTIAL GEAR KIT
  1. Check that there is no damage to the pinion gear and side gear.
    If the pinion gear and/or side gear is damaged, replace the differential gear kit.



24. INSPECT FRONT DIFFERENTIAL CASE
  1. Check that the differential case is not damaged.
    If the differential case is damaged, replace it.



25. REMOVE FRONT DIFFERENTIAL SIDE GEAR NEEDLE ROLLER BEARING


    C160136
  1. Using a brass bar and hammer, tap out the 2 bearings.



26. REMOVE DIFFERENTIAL CLUTCH HUB


    C159246
  1. Using a snap ring expander, remove the snap ring.

  1. Remove the differential clutch hub.



27. REMOVE DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL


    R013199E02
  1. Using SST, tap out the oil seal.

    SST
    09308-00010  



28. REMOVE DIFFERENTIAL SIDE GEAR SHAFT SUB-ASSEMBLY RH


    C159248
  1. Using a snap ring expander, remove the snap ring.



    C159247
  1. Using a plastic-faced hammer, tap out the side gear shaft.



29. REMOVE FRONT DIFFERENTIAL SIDE GEAR SHAFT RH BEARING


    C159249
  1. Using a snap ring expander, remove the snap ring.



    C159250E01
  1. Using SST, a brass bar and press, press out the bearing.

    SST
    09950-00020  
    09950-70010   (09951-07100)
    09950-60010   (09951-00450)

    NOTICE:
    Do not damage the bearing.



30. INSPECT DIFFERENTIAL CLUTCH SLEEVE AND DIFFERENTIAL CLUTCH HUB


    G023141
  1. Check for wear and damage to the clutch hub and clutch sleeve.
    If necessary, replace them.

  1. Check that the clutch sleeve slides smoothly on the clutch hub.



31. INSPECT DIFFERENTIAL CLUTCH SLEEVE AND DIFFERENTIAL SIDE GEAR INTER SHAFT


    G023144
  1. Check for wear and damage to the clutch hub and side gear inter shaft.

  1. Check that the clutch sleeve slides smoothly on the side gear inter shaft.



32. INSPECT DIFFERENTIAL CLUTCH SLEEVE AND CLUTCH SLEEVE FORK CLEARANCE


    C159251
  1. Using a feeler gauge, measure the clearance between the sleeve fork and clutch sleeve.

    Maximum clearance:
    0.35 mm (0.0138 in.)

    If the clearance more than the maximum, replace the fork or clutch sleeve.