Home › Drivetrain ยท AXLE AND DIFFERENTIAL › REAR DIFFERENTIAL CARRIER ASSEMBLY

REAR DIFFERENTIAL CARRIER ASSEMBLY > REASSEMBLY

for Preparation Click here



1. INSTALL STRAIGHT PIN


    C180992E02
  1. Using a plastic-faced hammer, tap in the straight pins until their protrusion amounts are at the specified values shown in the illustration below.

    Protrusion height:
    9.5 to 10 mm (0.374 to 0.394 in.)



2. INSTALL DIFFERENTIAL RING GEAR


    SA02160E03
  1. Clean the contact surfaces of the differential case and ring gear.

  1. Heat the ring gear to about 100°C (212°F) in boiling water.

  1. Carefully take the ring gear out of the boiling water.

  1. After the moisture on the ring gear has completely evaporated, quickly set the ring gear onto the differential case.

    HINT:
    1. Align the matchmarks on the ring gear and differential case.
    2. Temporarily install the 12 bolts so that the bolt holes in the ring gear and differential case are aligned.

  1. After the ring gear cools down sufficiently, apply adhesive to the bolts and install them.

    Torque:
    196 N*m{ 2000 kgf*cm , 145 ft.*lbf }

    Adhesive:
    Toyota Genuine Adhesive 1360K, Three Bond 1360K or equivalent



3. INSTALL REAR DIFFERENTIAL CASE BEARING


    C181022E01
  1. Using SST and a press, press in the 2 bearings (inner race).

    SST
    09950-70010   (09951-07100)



4. INSTALL REAR DIFFERENTIAL CASE BEARING

HINT:
When replacing the 2 differential case bearings, fit the thinnest washer to each bearing. When reusing the bearings, fit a washer of the same thickness as the one removed to each bearing.

  1. Install a new plate washer to the side bearing retainer.



    C180997E01
  1. Using SST and a press, press in the bearing (outer race) onto the differential case bearing retainer.

    SST
    09950-70010   (09951-07200)
    09951-01000  

  1. Install a new plate washer onto the differential carrier.



    C180999E01
  1. Using SST and a press, press in the bearing (outer race) onto the differential carrier assembly.

    SST
    09950-70010   (09951-07200)
    09951-01000  



5. INSTALL REAR DRIVE PINION FRONT RADIAL BALL BEARING


    C181037E01
  1. Using SST, install the bearing (outer race).

    SST
    09950-60020   (09951-00890)
    09218-56030  



6. INSTALL REAR DRIVE PINION REAR TAPERED ROLLER BEARING


    C181036E01
  1. Using SST, install the washer and bearing (outer race).

    SST
    09218-56030  
    09951-01100  

    HINT:
    First, fit a washer of the same thickness as the removed washer, and then after checking the tooth contact pattern, replace the washer with one of a different thickness if necessary.



7. INSTALL REAR DIFFERENTIAL CARRIER COVER BREATHER PLUG


    C180994
  1. Install the rear differential carrier cover breather plug with the 2 bolts.

    Torque:
    17 N*m{ 71 kgf*cm , 62 in.*lbf }



8. INSTALL REAR DRIVE PINION REAR TAPERED ROLLER BEARING


    C183213E01
  1. Using SST and a press, press in the bearing (inner race).

    SST
    09502-24010  
    09308-14010  



9. TEMPORARILY INSTALL DIFFERENTIAL DRIVE PINION
  1. Install the differential drive pinion.



10. INSTALL REAR DIFFERENTIAL CASE SUB-ASSEMBLY


    C180993
  1. Install the rear differential case sub-assembly.



11. INSTALL REAR DIFFERENTIAL SIDE BEARING RETAINER


    C180991
  1. Install the rear differential side bearing retainer with the 12 bolts.

    HINT:
    Tighten the bolts gradually, skipping to the bolt on the opposite side.

    Torque:
    70 N*m{ 714 kgf*cm , 52 ft.*lbf }



12. INSTALL REAR DIFFERENTIAL CARRIER COVER BREATHER PLUG


    C181031
  1. Install the rear differential carrier cover breather plug.

    Torque:
    21 N*m{ 210 kgf*cm , 15 ft.*lbf }



13. INSTALL REAR DRIVE PINION FRONT RADIAL BALL BEARING


    C181021E01
  1. Using SST and a hammer, lightly tap in the bearing (inner race) to install it.

    SST
    09316-60011   (09316-00011)
    09506-30012  



14. INSTALL REAR DIFFERENTIAL DRIVE PINION OIL SLINGER


    C181009
  1. Install the rear differential drive pinion oil slinger.



15. INSPECT DIFFERENTIAL DRIVE PINION PRELOAD


    C181018E01
  1. Using SST, install the companion flange.

    HINT:
    Use the propeller shaft installation nuts when mounting SST on the flange

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09956-03020)
    09955-03050  

  1. Coat the threads of the nut with hypoid gear oil.



    C181027E02
  1. Using SST to hold the companion flange.

    SST
    09330-00021  

  1. Using a 30 mm socket wrench, tighten the nut until the standard preload is reached.

    Torque:
    441 N*m{ 4497 kgf*cm , 325 ft.*lbf } or less

    NOTICE:
    1. As there is no spacer, tighten the nut a little at a time, being careful not to overtighten it.
    2. Install nuts on the bolts to protect them, as shown in the illustration.



    C181029
  1. Using a torque wrench, measure the preload of the backlash between the drive pinion and ring gear.

    Standard Preload (at Starting):
    Bearing
    Specified Condition
    New
    2.04 to 3.24 N*m (21 to 33 kgf*cm, 18 to 29 in.*lbf)
    Reused
    1.52 to 2.23 N*m (15 to 23 kgf*cm, 13 to 20 in.*lbf)

    If necessary, disassemble and inspect the differential assembly.



16. ADJUST BACKLASH BETWEEN DIFFERENTIAL RING GEAR AND DIFFERENTIAL DRIVE PINION


    C181024E01
  1. Using SST and a dial indicator, measure the ring gear backlash.

    SST
    09564-34010  

    Standard backlash:
    0.1 to 0.2 mm (0.00394 to 0.00787 in.)

    If the backlash is not within the specification, adjust it by either increasing or decreasing the thickness of the washers on both sides by an equal amount.

    HINT:
    1. There should be no clearance between the plate washer and differential case.
    2. Make sure that there is ring gear backlash.


    Standard Washer Thickness:

    Thickness
    Thickness
    1.55 to 1.57 mm (0.0610 to 0.0618 in.)
    1.91 to 1.93 mm (0.0752 to 0.0760 in.)
    1.57 to 1.59 mm (0.0618 to 0.0626 in.)
    1.93 to 1.95 mm (0.0760 to 0.0768 in.)
    1.59 to 1.61 mm (0.0626 to 0.0634 in.)
    1.95 to 1.97 mm (0.0768 to 0.0776 in.)
    1.61 to 1.63 mm (0.0634 to 0.0642 in.)
    1.97 to 1.99 mm (0.0776 to 0.0783 in.)
    1.63 to 1.65 mm (0.0642 to 0.0650 in.)
    1.99 to 2.01 mm (0.0783 to 0.0791 in.)
    1.65 to 1.67 mm (0.0650 to 0.0657 in.)
    2.01 to 2.03 mm (0.0791 to 0.0799 in.)
    1.67 to 1.69 mm (0.0657 to 0.0665 in.)
    2.03 to 2.05 mm (0.0799 to 0.0807 in.)
    1.69 to 1.71 mm (0.0665 to 0.0673 in.)
    2.05 to 2.07 mm (0.0807 to 0.0815 in.)
    1.71 to 1.73 mm (0.0673 to 0.0681 in.)
    2.07 to 2.09 mm (0.0815 to 0.0823 in.)
    1.73 to 1.75 mm (0.0681 to 0.0689 in.)
    2.09 to 2.11 mm (0.0823 to 0.0831 in.)
    1.75 to 1.77 mm (0.0689 to 0.0697 in.)
    2.11 to 2.13 mm (0.0831 to 0.0839 in.)
    1.77 to 1.79 mm (0.0697 to 0.0705 in.)
    2.13 to 2.15 mm (0.0839 to 0.0846 in.)
    1.79 to 1.81 mm (0.0705 to 0.0713 in.)
    2.15 to 2.17 mm (0.0846 to 0.0854 in.)
    1.81 to 1.83 mm (0.0713 to 0.0720 in.)
    2.17 to 2.19 mm (0.0854 to 0.0862 in.)
    1.83 to 1.85 mm (0.0720 to 0.0728 in.)
    2.19 to 2.21 mm (0.0862 to 0.0870 in.)
    1.85 to 1.87 mm (0.0728 to 0.0736 in.)
    2.21 to 2.23 mm (0.0870 to 0.0878 in.)
    1.87 to 1.89 mm (0.0736 to 0.0744 in.)
    2.23 to 2.25 mm (0.0878 to 0.0886 in.)
    1.89 to 1.91 mm (0.0744 to 0.0752 in.)
    2.25 to 2.27 mm (0.0886 to 0.0894 in.)



17. INSPECT TOTAL PRELOAD


    C181029
  1. Using a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.

    Standard Preload (at Starting):
    Bearing
    Specified Condition
    New
    2.33 to 4.47 N*m (24 to 46 kgf*cm, 21 to 40 in.*lbf)
    Reused
    1.79 to 3.34 N*m (18 to 34 kgf*cm, 16 to 30 in.*lbf)

    If necessary, disassemble and inspect the differential.



18. INSPECT TOOTH CONTACT BETWEEN RING GEAR AND DRIVE PINION
  1. Remove the bearing retainer and differential case.



    R013220
  1. Coat 3 or 4 teeth at 3 different positions on the ring gear with Prussian blue.

  1. Install the differential case to the differential carrier.



    C180991
  1. Install the rear differential side bearing retainer with the 12 bolts.

    HINT:
    Tighten the bolts gradually, skipping to the bolt on the opposite side.

    Torque:
    70 N*m{ 714 kgf*cm , 52 ft.*lbf }

  1. Hold the companion flange firmly and rotate the ring gear in both directions.

  1. Remove the differential case, side bearing retainer and differential case.



  1. Inspect the tooth contact pattern.


    C116070E02

    If the teeth are not engaged properly, use the following chart to select the appropriate washer for correction.

    Standard Washer Thickness:

    Thickness
    Thickness
    1.73 to 1.75 mm (0.0681 to 0.0689 in.)
    2.05 to 2.07 mm (0.0807 to 0.0815 in.)
    1.75 to 1.77 mm (0.0689 to 0.0697 in.)
    2.07 to 2.09 mm (0.0815 to 0.0823 in.)
    1.77 to 1.79 mm (0.0697 to 0.0705 in.)
    2.09 to 2.11 mm (0.0823 to 0.0831 in.)
    1.79 to 1.81 mm (0.0705 to 0.0713 in.)
    2.11 to 2.13 mm (0.0831 to 0.0839 in.)
    1.81 to 1.83 mm (0.0713 to 0.0720 in.)
    2.13 to 2.15 mm (0.0839 to 0.0846 in.)
    1.83 to 1.85 mm (0.0720 to 0.0728 in.)
    2.15 to 2.17 mm (0.0846 to 0.0854 in.)
    1.85 to 1.87 mm (0.0728 to 0.0736 in.)
    2.17 to 2.19 mm (0.0854 to 0.0862 in.)
    1.87 to 1.89 mm (0.0736 to 0.0744 in.)
    2.19 to 2.21 mm (0.0862 to 0.0870 in.)
    1.89 to 1.91 mm (0.0744 to 0.0752 in.)
    2.21 to 2.23 mm (0.0870 to 0.0878 in.)
    1.91 to 1.93 mm (0.0752 to 0.0760 in.)
    2.23 to 2.25 mm (0.0878 to 0.0886 in.)
    1.93 to 1.95 mm (0.0760 to 0.0768 in.)
    2.25 to 2.27 mm (0.0886 to 0.0894 in.)
    1.95 to 1.97 mm (0.0768 to 0.0776 in.)
    2.27 to 2.29 mm (0.0894 to 0.0902 in.)
    1.97 to 1.99 mm (0.0776 to 0.0783 in.)
    2.29 to 2.31 mm (0.0902 to 0.0910 in.)
    1.99 to 2.01 mm (0.0783 to 0.0791 in.)
    2.31 to 2.33 mm (0.0910 to 0.0917 in.)
    2.01 to 2.03 mm (0.0791 to 0.0799 in.)
    2.33 to 2.35 mm (0.0917 to 0.0925 in.)
    2.03 to 2.05 mm (0.0799 to 0.0807 in.)
    -



19. REMOVE REAR DRIVE PINION FRONT COMPANION FLANGE SUB-ASSEMBLY


    C181017E01
  1. Using SST, remove the rear drive pinion companion flange sub-assembly from the rear differential carrier assembly.

    HINT:
    Use the propeller shaft installation nuts when mounting SST on the flange.

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010)
    09955-03050  



20. REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER


21. REMOVE REAR DIFFERENTIAL SIDE BEARING RETAINER


    C180991
  1. Remove the 12 bolts and 2 straight pin.

  1. Using a plastic-faced hammer, tap out the rear differential side bearing retainer.



22. REMOVE REAR DIFFERENTIAL CASE SUB-ASSEMBLY


    C180993
  1. Remove the differential case from the differential carrier.



23. REMOVE DIFFERENTIAL DRIVE PINION
  1. Remove the differential case from the differential drive pinion.



24. REMOVE REAR DRIVE PINION FRONT RADIAL BALL BEARING


25. INSTALL REAR DIFFERENTIAL DRIVE PINION BEARING SPACER
  1. Install a new bearing spacer.



26. TEMPORARILY INSTALL DIFFERENTIAL DRIVE PINION


27. INSTALL REAR DIFFERENTIAL CASE SUB-ASSEMBLY


28. INSTALL REAR DIFFERENTIAL SIDE BEARING RETAINER
  1. Remove any old FIPG material and be careful not to drop oil on the contact surfaces of the differential carrier and side bearing retainer.

  1. Clean the contact surfaces with any residual FIPG material using gasoline or alcohol.

  1. Apply seal packing to the side bearing retainer as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent

    HINT:
    Install the side bearing retainer within 10 minutes of applying seal packing.



    C180991
  1. Install the rear differential side bearing retainer with the 12 bolts.

    HINT:
    Tighten the bolts gradually, skipping to the bolt on the opposite side.

    Torque:
    70 N*m{ 714 kgf*cm , 52 ft.*lbf }



29. INSTALL REAR DRIVE PINION FRONT RADIAL BALL BEARING


    C181021E01
  1. Using SST and a hammer, lightly tap in the bearing (inner race) to install it.

    SST
    09316-60011   (09316-00011)
    09506-30012  



30. INSTALL REAR DIFFERENTIAL DRIVE PINION OIL SLINGER


    C181009
  1. Install the rear differential drive pinion oil slinger.



31. INSTALL REAR DIFFERENTIAL CARRIER OIL SEAL


    C181145E01
  1. Using SST and a hammer, tap in a new oil seal.

    SST
    09223-56010  
    09527-17011  

    Standard depth:
    0 to 0.1 mm (0 to 0.0394 in.)

  1. Coat the lip of the oil seal with MP grease.



32. INSTALL REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY FRONT


    C181018E01
  1. Using SST, install the companion flange.

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010)
    09955-03050  

    HINT:
    Use the propeller shaft installation nuts when mounting SST on the flange.



33. INSPECT DIFFERENTIAL DRIVE PINION PRELOAD


    C181027E02
  1. Using SST to hold the companion flange.

    SST
    09330-00021   (09330-00030)

  1. Coat the threads of a new nut with hypoid gear oil.

  1. Using a socket wrench (30mm). install the nut by tightening it until the standard preload is reached.

    NOTICE:
    Install nuts on the bolts to protect them, as shown in the illustration.

    Torque:
    441 N*m{ 4497 kgf*cm , 325 ft.*lbf } or less



    C181029
  1. Using a torque wrench, measure the preload of the backlash between the drive pinion and ring gear.

    Standard Preload (at Starting):
    Bearing
    Specified Condition
    New
    2.04 to 3.24 N*m (21 to 33 kgf*cm, 18 to 29 in.*lbf)
    Reused
    1.52 to 2.23 N*m (15 to 23 kgf*cm, 13 to 20 in.*lbf)

    If the preload is greater than the specification, replace the bearing spacer.
    If the preload is less than the specification, retighten the nut with until the specified preload is reached.

    Torque:
    441 N*m{ 4497 kgf*cm , 325 ft.*lbf } or less

    If the maximum torque is exceeded while retightening the nut, replace the bearing spacer and repeat the preload procedure.

    HINT:
    Do not loosen the nut to reduce the preload.



34. INSPECT TOTAL PRELOAD


    C181029
  1. With the drive pinion contacting the tooth side of the ring gear, use a torque wrench to measure the total preload.

    Standard Preload (at Starting):
    Bearing
    Specified Condition
    New
    2.33 to 4.47 N*m (24 to 46 kgf*cm, 21 to 40 in.*lbf)
    Reused
    1.79 to 3.34 N*m (18 to 34 kgf*cm, 16 to 30 in.*lbf)



35. INSPECT BACKLASH BETWEEN DIFFERENTIAL RING GEAR AND DIFFERENTIAL DRIVE PINION


    C181024E01
  1. Using SST and a dial indicator, measure the ring gear backlash.

    SST
    09564-34010  

    Standard backlash:
    0.1 to 0.2 mm (0.00394 to 0.00787 in.)



36. INSPECT RUNOUT OF REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY


    C181030E02
  1. Using a dial indicator, measure the runout of the companion flange vertically and laterally.

    Maximum Runout:
    Runout
    Specified Condition
    Vertical runout
    0.1 mm (0.00394 in.)
    Lateral runout
    0.1 mm (0.00394 in.)

    If the runout is greater than the maximum, replace the companion flange.



37. STAKE REAR DRIVE PINION NUT


    C181003E01
  1. Using a chisel and hammer, stake the nut.

    SST
    09930-00010  



38. INSTALL REAR DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL
  1. Apply MP grease to 2 new oil seals.



    C181006E02
  1. Using SST and a hammer, tap in the 2 oil seals.

    SST
    09223-15020  
    09950-70010   (09951-07150)

    NOTICE:
    Make sure that the oil seal are installed in the proper locations.

    Standard depth:
    -0.50 to 0.50 mm (-0.0197 to 0.0197 in.)