Home › Brake › BRAKE (REAR) › REAR BRAKE

REAR BRAKE > INSTALLATION

for Preparation Click here



1. INSTALL REAR DISC


    C178157E02
  1. Align the matchmarks and install the rear disc.



2. ADJUST PARKING BRAKE SHOE CLEARANCE
  1. Temporarily install the hub nuts.

  1. Remove the hole plug.



    C158874E01
  1. Insert an adjustment tool into the adjustment hole of the disc. Rotate the adjustment wheel in the "X" direction until the shoes are locked. Then rotate the adjustment wheel in the "Y" direction 8 notches.

  1. Check that the disc can be rotated smoothly. If not, rotate the adjustment wheel in the "Y" direction and check again.

  1. Install the hole plug.

  1. Remove the hub nuts.



3. INSTALL REAR DISC BRAKE CYLINDER MOUNTING LH

NOTICE:
  1. The pad support plates are attached to the rear disc brake cylinder mounting with double-sided tape. When removing the brake pads, make sure the pad support plates are not detached. If the pad support plates are not detached, they can be reused. If they are detached, replace the pad support plates with new ones.
  2. If the pad support plates are removed during maintenance of parts, replace them with new ones.



    C193370E01
  1. Apply a light layer of lithium soap base glycol grease to the entire circumference of a new rear disc brake bush dust boot where it contacts the rear disc brake mounting cylinder, and the entire inner circumference of both ends.

    NOTICE:
    Apply a sufficient amount of lithium soap base glycol grease to the entire circumference of the rear disc brake bush dust boot and rear disc brake cylinder mounting contact surfaces.

    HINT:
    Apply at least 0.3 g (0.01 oz.) of lithium soap base glycol grease to each rear disc brake bush dust boot.



    C180571
  1. Install the 2 boots to the rear disc brake cylinder mounting.

    NOTICE:
    Install the boot securely into the grooves of the rear disc brake cylinder mounting.

  1. Install the rear disc brake cylinder mounting with the 2 bolts.

    Torque:
    95 N*m{ 969 kgf*cm , 70 ft.*lbf }



4. INSTALL REAR DISC BRAKE PAD SUPPORT PLATE

NOTICE:
  1. The pad support plates are attached to the rear disc brake cylinder mounting with double-sided tape. When removing the brake pads, make sure the pad support plates are not detached. If the pad support plates are not detached, they can be reused. If they are detached, replace the pad support plates with new ones.
  2. If the pad support plates are removed during maintenance of parts, replace them with new ones.

  1. Install 4 new pad support plates to the rear disc brake cylinder mounting.

    NOTICE:
    1. Before installing the pad support plates, clean the installation area on the mounting.
    2. New pad support plates have double-sided tape attached to them. Remove the peeling paper from the double-sided tape, and attach the pad support plates to the mounting by pressing them with your finger for more than 10 seconds.



5. INSTALL PAD WEAR INDICATOR PLATE
  1. Install the pad wear indicator plate to the inner disc brake pad.



6. INSTALL REAR DISC BRAKE ANTI-SQUEAL SHIM
  1. Install the anti-squeal shims to the brake pads.

    NOTICE:
    There should be no oil or grease on the friction surfaces of the brake pads and rear disc.



7. INSTALL REAR DISC BRAKE PAD
  1. Install the 2 disc brake pads to the disc brake cylinder mounting.



8. INSTALL REAR DISC BRAKE CYLINDER ASSEMBLY LH


    C193405E01
  1. Apply lithium soap base glycol grease to the sliding part and seal surface of the 2 slide pins.



    C180572
  1. Install the 2 slide pins.

    Torque:
    88 N*m{ 897 kgf*cm , 65 ft.*lbf }



9. CONNECT REAR FLEXIBLE HOSE LH


    C180573
  1. Install a new gasket and connect the flexible hose with a new union bolt.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }



10. FILL RESERVOIR WITH BRAKE FLUID

Fluid:
SAE J1703 or FMVSS No. 116 DOT3

NOTICE:
  1. Make sure there is sufficient brake fluid in the can.
  2. After adding brake fluid, make sure the reservoir is sufficiently full.



11. BLEED AIR FROM BRAKE MASTER CYLINDER

HINT:
If the master cylinder has been disassembled or if the reservoir becomes empty, bleed air from the master cylinder.



    C155473E04
  1. Using a union nut wrench, disconnect the 2 brake lines from the master cylinder.

  1. Slowly depress and hold the brake pedal.



    C155474
  1. Block the outer holes with your fingers, and release the pedal.

  1. Repeat the 2 previous steps 3 or 4 times.

  1. Using a union nut wrench, connect the 2 brake lines to the master cylinder.

    Torque:
    without union nut wrench:
    20 N*m{ 199 kgf*cm , 14 ft.*lbf }
    with union nut wrench:
    18 N*m{ 187 kgf*cm , 13 ft.*lbf }

    HINT:
    1. Use a torque wrench with a fulcrum length of 300 mm (11.8 in.).
    2. This torque value is effective when union nut wrench is parallel to the torque wrench.



12. BLEED AIR FROM BRAKE LINE



C155475E01

  1. Remove the bleeder plug cap.

  1. Connect the vinyl tube to the bleeder plug.

  1. Depress the brake pedal several times, and then loosen the bleeder plug with the pedal depressed.

  1. When fluid stops coming out, immediately tighten the bleeder plug. Then release the pedal.

  1. Repeat the 2 previous steps until all the air in the brake fluid is gone.

  1. Tighten the bleeder plug.

    Torque:
    11 N*m{ 110 kgf*cm , 8 ft.*lbf }

  1. Install the cap.

  1. Bleed air from the brake line for each wheel by repeating the above procedures.



13. BLEED AIR FROM VSC ACTUATOR ASSEMBLY

NOTICE:
After bleeding the air from the brake system, if the height or feel of the brake pedal cannot be obtained, perform air bleeding of the brake actuator with the intelligent tester by following the procedure below.

  1. Depress the brake pedal more than 20 times with the engine off.

  1. Connect the intelligent tester to the DLC3, and turn the ignition switch on.

    NOTICE:
    Do not start the engine.

  1. Select AIR BLEEDING on the intelligent tester.

    HINT:
    Refer to the intelligent tester operator's manual for further details.

  1. Bleed the air out of the suction line.

    NOTICE:
    1. Perform the bleeding at the right front wheel and right rear wheel.
    2. Bleed the air by following the steps displayed on the intelligent tester.


    1. Connect a vinyl tube to the bleeder plug at the right front wheel or the right rear wheel.

    2. Loosen the bleeder plug.

    3. Operate the brake actuator to bleed the air using the intelligent tester.

      NOTICE:
      Release the brake pedal at this time.

      HINT:
      This operation stops automatically after 4 seconds.

    4. Check if the operation has stopped by referring to the intelligent tester display.

    5. Temporarily tighten the bleeder plug.

    6. Repeat the 4 previous steps until all air in the fluid is completely bled out.

    7. Tighten the bleeder plug.

      Torque:
      11 N*m{ 110 kgf*cm , 8 ft.*lbf }

    8. Repeat all of the above procedures for the other wheel to bleed the air out of the suction line.

  1. Bleed the air out of the pressure reduction line.

    NOTICE:
    1. Perform the bleeding at the 4 wheels.
    2. Bleed the air by following the steps displayed on the intelligent tester.


    1. Connect a vinyl tube to one of the bleeder plugs.

    2. Loosen the bleeder plug.

    3. Using the intelligent tester, operate the brake actuator, completely depress the brake pedal and hold it there.

      NOTICE:
      1. During this procedure, the pedal will feel heavy, but completely depress it so that the brake fluid comes out of the bleeder plug.
      2. Depress and hold the brake pedal. Do not depress and release the pedal repeatedly.

      HINT:
      The operation stops automatically after 4 seconds. When performing this procedure continuously, set an interval of at least 20 seconds.

    4. Tighten the bleeder plug, and then release the brake pedal.

    5. Repeat the 3 previous steps until all air in the fluid is completely bled out.

    6. Tighten the bleeder plug.

      Torque:
      11 N*m{ 110 kgf*cm , 8 ft.*lbf }

    7. Repeat all of the above procedures for the other wheels to bleed the air out of the pressure reduction line.



14. CHECK BRAKE FLUID LEVEL IN RESERVOIR


    C155477
  1. Check the fluid level and add fluid if necessary.

    Fluid:
    SAE J1703 or FMVSS No. 116 DOT3

    HINT:
    Add fluid to a level between the reservoir's MIN and MAX lines.



15. INSPECT FOR BRAKE FLUID LEAK


16. INSTALL REAR WHEEL

Torque:
131 N*m{ 1336 kgf*cm , 97 ft.*lbf }