NAME PLATE > INSTALLATION |
| 1. INSTALL NO. 3 BACK DOOR NAME PLATE |
Clean the attachment surface.
Using an infrared light, heat the double-sided adhesive tape remaining on the back door panel.
Using a piece of cloth, rub the double-sided adhesive tape off the back door panel while it is hot from the infrared light.
Using a non-residue solvent, clean the attachment surface.
![]() |
Install a new No. 3 back door name plate as shown in the illustration.
| Mark | Measurement (Along Surface) |
| a | 99.2 mm (3.91 in.) |
| b | 104.5 mm (4.11 in.) |
| c | 98.6 mm (3.88 in.) |
| 2. INSTALL NO. 4 BACK DOOR NAME PLATE |
Clean the attachment surface.
Using an infrared light, heat the double-sided adhesive tape remaining on the back door panel.
Using a piece of cloth, rub the double-sided adhesive tape off the back door panel while it is hot from the infrared light.
Using a non-residue solvent, clean the attachment surface.
![]() |
Install a new No. 4 back door name plate as shown in the illustration.
| Mark | Measurement (Along Surface) |
| a | 112.8 mm (4.44 in.) |
| b | 87.8 mm (3.46 in.) |
| c | 113.9 mm (4.48 in.) |
| 3. INSTALL SYMBOL EMBLEM |
![]() |
Clean the attachment surface.
Using an infrared light, heat the double-sided adhesive tape remaining on the back door panel.
Using a piece of cloth, rub the remaining double-sided adhesive tape off the back door panel while it is hot from the infrared light.
Using a non-residue solvent, clean the attachment surface.
Insert the 2 pins into the back door panel and install the symbol emblem.
| 4. INSTALL NO. 1 ROOF SIDE MARK (PLATINUM) |
Clean the attachment surface.
Using an infrared light, heat the double-sided adhesive tape remaining on the rear door panel.
Using a piece of cloth, rub the double-sided adhesive tape off the rear door panel while it is hot from the infrared light.
Using a non-residue solvent, clean the attachment surface.
![]() |
Install a new No. 1 roof side mark as shown in the illustration.
| Mark | Measurement (Along Surface) |
| a | 4.6 mm (0.181 in.) |
| b | 19.5 mm (0.768 in.) |
| c | 4.6 mm (0.181 in.) |
| d | 4.6 mm (0.181 in.) |
| e | 16.3 mm (0.642 in.) |
| f | 4.6 mm (0.181 in.) |
| 5. INSTALL NO. 1 ROOF SIDE MARK (LIMITED) |
Clean the attachment surface.
Using an infrared light, heat the double-sided adhesive tape remaining on the rear door panel.
Using a piece of cloth, rub the double-sided adhesive tape off the rear door panel while it is hot from the infrared light.
Using a non-residue solvent, clean the attachment surface.
![]() |
Install a new No. 1 roof side mark as shown in the illustration.
| Mark | Measurement (Along Surface) |
| a | 4.6 mm (0.181 in.) |
| b | 26.6 mm (1.05 in.) |
| c | 4.6 mm (0.181 in.) |
| d | 4.6 mm (0.181 in.) |
| e | 16 mm (0.630 in.) |
| f | 4.6 mm (0.181 in.) |
| 6. INSTALL NO. 1 ROOF SIDE MARK (SRS) |
Clean the attachment surface.
Using an infrared light, heat the double-sided adhesive tape remaining on the rear door panel.
Using a piece of cloth, rub the double-sided adhesive tape off the rear door panel while it is hot from the infrared light.
Using a non-residue solvent, clean the attachment surface.
![]() |
Install a new No. 1 roof side mark as shown in the illustration.
| Mark | Measurement (Along Surface) |
| a | 4.7 mm (0.185 in.) |
| b | 33.6 mm (1.32 in.) |
| c | 4.5 mm (0.177 in.) |
| d | 4.4 mm (0.173 in.) |
| e | 34.1 mm (1.34 in.) |
| f | 4.5 mm (0.177 in.) |