AUTOMATIC TRANSMISSION ASSEMBLY > REMOVAL |
| 1. DRAIN AUTOMATIC TRANSMISSION FLUID |
Remove the drain plug and gasket, and drain ATF.
Install a new gasket and the drain plug.
| 2. DRAIN ENGINE COOLANT |
Loosen the radiator drain cock plug.
Remove the radiator cap. Then drain the coolant from the radiator.
Loosen the 2 cylinder block drain cock plugs. Then drain the coolant from the engine.
Tighten the 2 cylinder block drain cock plugs.
Tighten the radiator drain cock plug by hand.

| 3. REMOVE PROPELLER SHAFT ASSEMBLY |
Remove the propeller shaft assembly (Click here).
| 4. REMOVE FRONT EXHAUST PIPE ASSEMBLY |
Disconnect the air fuel ratio sensor connector.
![]() |
Remove the 3 nuts, front exhaust pipe and gasket from the exhaust manifold RH.
| 5. REMOVE FRONT NO. 3 EXHAUST PIPE ASSEMBLY |
![]() |
Remove the 2 bolts and 2 nuts.
Disconnect the front No. 3 exhaust pipe sub-assembly from the exhaust pipe support.
Remove the front No. 3 exhaust pipe sub-assembly from the front No. 2 exhaust pipe sub-assembly.
Disconnect the air fuel ratio sensor connector.
![]() |
Remove the 3 nuts, front No. 2 exhaust pipe sub-assembly and 2 gaskets from the exhaust manifold LH.
| 6. DISCONNECT WATER BY-PASS PIPE ASSEMBLY |
![]() |
Remove the bolt and disconnect the 2 water by-pass hoses from the transmission oil cooler. Then separate the by-pass pipe from the automatic transmission.
| 7. DISCONNECT NO. 2 OIL COOLER HOSE |
![]() |
Loosen the 2 clips and disconnect the inlet No. 2 oil cooler hose and outlet No. 2 oil cooler hose.
| 8. DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY |
![]() |
Remove the nut and clip, and disconnect the transmission control cable.
| 9. REMOVE STARTER ASSEMBLY |
Remove the starter assembly (Click here).
| 10. REMOVE DRIVE PLATE AND TORQUE CONVERTER SETTING BOLT |
![]() |
Turn the crankshaft to gain access to the 6 bolts and remove the bolts while holding the crankshaft pulley setting bolt with a wrench.
| 11. SUPPORT AUTOMATIC TRANSMISSION ASSEMBLY |
![]() |
Support the automatic transmission with a transmission jack. Lift the automatic transmission slightly from the crossmember.
| 12. REMOVE NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY |
![]() |
Remove the 4 bolts of the rear No. 1 engine mounting insulator.
![]() |
Remove the 4 nuts, 4 washers, 4 bolts and No. 3 frame crossmember.
| 13. REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR |
![]() |
Remove the 4 bolts and rear No. 1 engine mounting insulator from the automatic transmission.
| 14. DISCONNECT WIRE HARNESS AND CONNECTOR |
![]() |
Remove the bolt and disconnect the ground cable.
![]() |
Tilt the automatic transmission downward.
![]() |
Disconnect the park/neutral position switch connector, 2 transmission wire connectors and 2 speed sensor connectors.
Disconnect the 3 connector clamps and 4 harness clamps.
Remove the 2 bolts and disconnect the harness clamps and wire harness.
| 15. DISCONNECT BREATHER PLUG HOSE |
![]() |
Disconnect the breather plug hose from the harness clamp bracket.
| 16. REMOVE AUTOMATIC TRANSMISSION ASSEMBLY |
![]() |
Remove the 10 bolts and automatic transmission.
| 17. REMOVE CONNECTOR CLAMP BRACKET |
Remove the 3 bolts and 3 oxygen sensor connector clamp brackets from the automatic transmission.
| 18. REMOVE TRANSMISSION CONTROL CABLE BRACKET |
![]() |
Remove the 2 bolts and transmission control cable bracket.
| 19. REMOVE TORQUE CONVERTER ASSEMBLY |
![]() |
Put matchmarks on the transmission case and torque converter.
Remove the torque converter from the automatic transmission.
| 20. INSPECT TORQUE CONVERTER AND DRIVE PLATE |
Inspect the torque converter and drive plate (Click here).