Home › Vehicle Exterior › DOOR / HATCH › BACK DOOR

BACK DOOR > DISASSEMBLY

for Preparation Click here


CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (Click here).



1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
When disconnecting the cable some systems need to be initialized after the cable is reconnected (Click here).



3. REMOVE POWER BACK DOOR ROD (w/ Power Back Door)


    B194506E01
  1. Using a screwdriver with its tip wrapped in protective tape, remove the 2 stop rings and power back door rod.



4. REMOVE BACK DOOR CENTER GARNISH


    B190514
  1. Detach the 4 clips and the claw and remove the back door center garnish.



5. REMOVE BACK DOOR SIDE GARNISH RH


    B190515
  1. Detach the 2 clips and remove the back door side garnish RH.



6. REMOVE BACK DOOR SIDE GARNISH LH


    B190516
  1. Detach the 3 clips and remove the back door side garnish LH



7. REMOVE BACK DOOR STAY LOWER BRACKET (w/ Power Back Door)


    B194233
  1. Remove the 2 bolts and remove the back door stay lower bracket.



8. REMOVE BACK DOOR STRAP COVER


    B190517
  1. Slide the back door strap cover and detach the claw and remove the back door strap cover.



9. REMOVE BACK DOOR PULL STRAP


    B190519
  1. Remove the bolt and remove the back door pull strap.



10. REMOVE BACK DOOR TRIM BOARD ASSEMBLY


    B190520
  1. Detach the 11 clips and remove the back door trim board assembly.



11. REMOVE BACK DOOR GLASS WEATHERSTRIP


    B190511
  1. Raise the 9 claws of the rear back door glass weatherstrip and then remove the back door glass weatherstrip from the back door trim board assembly, as shown in the illustration.



12. REMOVE BACK DOOR SERVICE HOLE COVER


    B190521
  1. Remove the back door service hole cover.

    NOTICE:
    Remove any tape remaining on the door.



13. REMOVE POWER BACK DOOR WARNING BUZZER (w/ Power Back Door)


    B190524
  1. Disconnect the connector.

  1. Detach the clamp and remove the power back door warning buzzer.



14. REMOVE MULTIPLEX NETWORK BODY ECU (w/ Power Back Door)


    B194490
  1. Disconnect the 2 connectors and detach the 2 clamps.

  1. Remove the 2 screws and remove the multiplex network body ECU.



15. REMOVE BACK DOOR NO. 2 SERVICE HOLE COVER


    B190525
  1. Remove the 3 screws and detach the 2 clips and remove the back door No. 2 service hole cover.



16. REMOVE POWER BACK DOOR SENSOR RH
  1. Disconnect the connector.



    B192122
  1. Remove the 6 screws.

  1. Detach the 2 clips and remove the power back door sensor.



17. REMOVE POWER BACK DOOR SENSOR LH


    B192121
  1. Disconnect the connector.

  1. Remove the 6 screws.

  1. Detach the 2 clips and remove the power back door sensor assembly.



18. REMOVE REAR WIPER ARM HEAD CAP


    E161700
  1. Detach the claw and remove the rear wiper arm head cap.



19. REMOVE REAR WIPER BLADE ASSEMBLY


    E161701
  1. Remove the nut and remove the rear wiper blade assembly.



20. REMOVE REAR WIPER MOTOR ASSEMBLY


    E161698
  1. Detach the clamp and disconnect the connector.

  1. Loosen the 3 bolts and remove the rear wiper motor.

    NOTICE:
    Do not try to remove the bolts since they are integrated with the motor.



21. REMOVE REAR WIPER MOTOR GROMMET


    E161696
  1. Remove the rear wiper motor grommet.



22. REMOVE REAR WIPER STOPPER


    B190526
  1. Detach the claw and guide, and remove the linear wiper step RH.



23. REMOVE BACK DOOR OUTSIDE MOULDING LH


    B191708
  1. Detach the 5 clips and remove the back door outside moulding.



24. REMOVE BACK DOOR OUTSIDE MOULDING RH

HINT:
Use the same procedure as for the LH side.



25. REMOVE BACK DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY


    B195691E01
  1. Apply protective tape to the door panel in the area around the back door glass outer weatherstrip.



    B195692E01
  1. Using a moulding remover, detach the 9 claws and remove the back door glass outer weatherstrip.



26. REMOVE BACK DOOR GLASS RUN


    B190527
  1. Remove the back door glass run.



27. REMOVE BACK DOOR GLASS


    B190513
  1. Remove the hole plug.

  1. Provisionally install the multiplex network body ECU.



    B190528
  1. Move the back door glass until the 4 bolts can be seen through the service holes.

  1. Disconnect the 2 connectors.

  1. Remove the 4 bolts and remove the back door glass.

    NOTICE:
    Do not drop or damage the back door glass.

  1. Remove the multiplex network body ECU.



28. REMOVE BACK DOOR POWER WINDOW REGULATOR ASSEMBLY


    B190529E01
  1. Disconnect the connector.

  1. Loosen nut A.

  1. Remove the 5 nuts, then remove the back door power window regulator assembly.

    NOTICE:
    Do not drop or damage the back door power window regulator assembly when removing the nuts.



29. REMOVE BACK DOOR LOCK CYLINDER


    B190530
  1. Disconnect the connector

  1. Remove the 2 nuts and remove the back door lock cylinder.



30. REMOVE BACK DOOR OUTSIDE GARNISH


B191712
  1. Remove the 4 nuts.

  1. Disconnect the connector.



    B191713
  1. Detach the 2 clips and remove the back door outside garnish.



31. REMOVE REAR TELEVISION CAMERA ASSEMBLY (w/Television Camera:)


    E260238
  1. Disconnect the connector.



    E192392
  1. Detach the 2 claws and remove the rear television camera.



32. REMOVE LICENSE PLATE LIGHT ASSEMBLY


    E161800
  1. Remove the 4 screws.

  1. Disconnect the 4 harness clamps and remove the license plate light.



33. REMOVE BACK DOOR OUTSIDE HANDLE
  1. Disconnect the connector.



    B190531
  1. Detach the clamp.

  1. Remove the 2 bolts and remove the back door outside handle.



34. REMOVE BACK DOOR LOCK PROTECTOR


    B223976
  1. Detach the 3 claws and back door lock protector sub-assembly.



35. REMOVE BACK DOOR LOCK (w/o Power Back Door)


B190532
  1. Disconnect the connector.

  1. Detach the clamp.

  1. Remove the 3 bolts and back door lock.



36. REMOVE BACK DOOR LOCK (w/ Power Back Door)


B194235
  1. Disconnect the connector.

  1. Detach the clamp.

  1. Remove the 4 bolts and back door lock.



37. REMOVE REAR LIGHT ASSEMBLY RH


    E161831
  1. Disconnect the connector.

  1. Remove the 2 nuts.

  1. Disengage the clip and remove the rear light.



38. REMOVE REAR LIGHT ASSEMBLY LH


    E161831
  1. Disconnect the connector.

  1. Remove the 2 nuts.

  1. Disengage the clip and remove the rear light.



39. REMOVE REAR SPOILER COVER
  1. Disconnect the connector.



    B191670
  1. Remove the 2 hole plugs.



    B191671
  1. Remove the 2 nuts.



    B219634E01
  1. Detach the 5 pins and remove the rear spoiler.