Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM

VEHICLE STABILITY CONTROL SYSTEM > Brake Warning Light Remains ON

for Preparation Click here


DESCRIPTION

If any of the following conditions are detected, the brake warning light remains on:
  1. The ECU connector is disconnected from the skid control ECU.
  2. The brake fluid level is insufficient.
  3. The parking brake is applied.
  4. The EBD system is malfunctioning.
  5. The booster vacuum pressure is abnormal.
  6. The pedal stroke sensor is malfunctioning.

WIRING DIAGRAM


C244862E02


INSPECTION PROCEDURE

NOTICE:
When replacing the VSC actuator assembly, perform zero point calibration (Click here).

1.PREPARE FOR INSPECTION
  1. Check that both of the following conditions are satisfied.

    1. The brake fluid level in the brake master cylinder reservoir is correct.
    2. The parking brake is released.

    HINT:
    1. When the ABS warning light remains illuminated, repair the malfunction in the ABS system first.
    2. When the slip indicator light remains illuminated, repair the malfunction in the VSC system first.


NEXT


2.CHECK DTC
  1. Check if any ABS DTCs are output (Click here).
    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
REPAIR CIRCUITS INDICATED BY OUTPUT DTCS
A


3.CHECK CAN COMMUNICATION SYSTEM
  1. Check if the CAN communication system DTC is output (Click here).
    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
GO TO CAN COMMUNICATION SYSTEM (Click here)
A


4.CHECK CONNECTOR CONNECTION CONDITION
  1. Check if the skid control ECU connector is connected securely.

    OK:
    The connector is connected securely.



NG
CONNECT CONNECTOR CORRECTLY
OK


5.CHECK PARKING BRAKE SWITCH ASSEMBLY
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester ON.

  1. Select Data List mode and check the parking brake switch using the intelligent tester.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Parking Brake SW
    Parking brake switch / ON or OFF
    ON: Parking brake applied
    OFF: Parking brake released
    -

  1. Check that "ON" and "OFF" are properly indicated on the intelligent tester display when the parking brake lever is operated.

    OK:
    Intelligent tester display changes in accordance with the parking brake lever operation.



NG
Go to step 9
OK


6.CHECK BRAKE FLUID LEVEL WARNING SWITCH

C160042E03

  1. Remove the reservoir tank cap and strainer.

  1. Disconnect the A3 switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    HINT:
    A float is placed inside the reservoir. Its position can be changed by increasing or decreasing the brake fluid level.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 (+) - 2 (E)
    Float up (Switch OFF)
    10 kΩ or higher
    1 (+) - 2 (E)
    Float down (Switch ON)
    Below 1 Ω

    HINT:
    If the result is as specified, adjust the brake fluid level to the MAX level after measuring the resistance.



NG
REPLACE BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY
OK


7.CHECK HARNESS AND CONNECTOR (COMBINATION METER - BRAKE FLUID LEVEL WARNING SWITCH)


    C160043E02
  1. Disconnect the H37 meter connector.

  1. Disconnect the A3 switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H37-14 (SW) - A3-1 (+)
    Always
    Below 1 Ω
    H37-14 (SW) - Body ground
    Always
    10 kΩ or higher
    A3-2 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (BRAKE WARNING LIGHT)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester ON.

  1. Select Active Test mode and operate the brake warning light using the intelligent tester.

    ABS/VSC/TRC 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Brake Warning Light
    Brake warning light
    Warning light ON/OFF
    Observe combination meter

  1. Check that the brake warning light turns on and off in the combination meter using the intelligent tester.

    OK:
    The brake warning light turns ON and OFF in accordance with the intelligent tester operation.



NG
GO TO METER / GAUGE SYSTEM (Click here)
OK

REPLACE COMBINATION METER (Click here)  

9.INSPECT PARKING BRAKE SWITCH ASSEMBLY


    C160219E03
  1. Disconnect the A5 switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - Body ground
    Parking brake switch ON
    (Switch pin released)
    Below 1 Ω
    1 - Body ground
    Parking brake switch OFF
    (Switch pin pushed in)
    10 kΩ or higher



NG
REPLACE PARKING BRAKE SWITCH ASSEMBLY (Click here)
OK


10.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - PARKING BRAKE SWITCH)


    C240528E02
  1. Disconnect the A19 ECU connector.

  1. Disconnect the A5 switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A19-14 (PKB2) - A5-1
    Always
    Below 1 Ω
    A19-14 (PKB2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE VSC ACTUATOR ASSEMBLY (Click here)