OUTER MIRROR SWITCH > INSPECTION |
| 1. INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/o Retract Mirror) |
![]() |
Inspect the outer mirror switch assembly.
Select "L" on the left/right adjustment switch.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition | |
| 4 (MLV) - 8 (B) 6 (M+) - 7 (E) | UP | Pressed | Below 1 Ω |
| Not pressed | 10 kΩ or higher | ||
| 4 (MLV) - 7 (E) 6 (M+) - 8 (B) | DOWN | Pressed | Below 1 Ω |
| Not pressed | 10 kΩ or higher | ||
| 5 (MLH) - 8 (B) 6 (M+) - 7 (E) | LEFT | Pressed | Below 1 Ω |
| Not pressed | 10 kΩ or higher | ||
| 5 (MLH) - 7 (E) 6 (M+) - 8 (B) | RIGHT | Pressed | Below 1 Ω |
| Not pressed | 10 kΩ or higher | ||
Select "R" on the left/right adjustment switch.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition | |
| 3 (MRV) - 8 (B) 6 (M+) - 7 (E) | UP | Pressed | Below 1 Ω |
| Not pressed | 10 kΩ or higher | ||
| 3 (MRV) - 7 (E) 6 (M+) - 8 (B) | DOWN | Pressed | Below 1 Ω |
| Not pressed | 10 kΩ or higher | ||
| 2 (MRH) - 8 (B) 6 (M+) - 7 (E) | LEFT | Pressed | Below 1 Ω |
| Not pressed | 10 kΩ or higher | ||
| 2 (MRH) - 7 (E) 6 (M+) - 8 (B) | RIGHT | Pressed | Below 1 Ω |
| Not pressed | 10 kΩ or higher | ||
| 2. INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/ Retract Mirror) |
![]() |
Inspect the outer mirror switch assembly.
Select "L" on the left/right adjustment switch.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition | |
| 4 (MLV) - 8 (B) 6 (M+) - 7 (E) | UP | Pressed | Below 1 Ω |
| Not pressed | 10 kΩ or higher | ||
| 4 (MLV) - 7 (E) 6 (M+) - 8 (B) | DOWN | Pressed | Below 1 Ω |
| Not pressed | 10 kΩ or higher | ||
| 5 (MLH) - 8 (B) 6 (M+) - 7 (E) | LEFT | Pressed | Below 1 Ω |
| Not pressed | 10 kΩ or higher | ||
| 5 (MLH) - 7 (E) 6 (M+) - 8 (B) | RIGHT | Pressed | Below 1 Ω |
| Not pressed | 10 kΩ or higher | ||
Select "R" on the left/right adjustment switch.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition | |
| 3 (MRV) - 8 (B) 6 (M+) - 7 (E) | UP | Pressed | Below 1 Ω |
| Not pressed | 10 kΩ or higher | ||
| 3 (MRV) - 7 (E) 6 (M+) - 8 (B) | DOWN | Pressed | Below 1 Ω |
| Not pressed | 10 kΩ or higher | ||
| 2 (MRH) - 8 (B) 6 (M+) - 7 (E) | LEFT | Pressed | Below 1 Ω |
| Not pressed | 10 kΩ or higher | ||
| 2 (MRH) - 7 (E) 6 (M+) - 8 (B) | RIGHT | Pressed | Below 1 Ω |
| Not pressed | 10 kΩ or higher | ||
Inspect the retract switch.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 8 (B) - 9 (MR) 10 (MF) - 7 (E) | Pressed | Below 1 Ω |
| Not pressed | 10 kΩ or higher | |
| 8 (B) - 10 (MF) 7 (E) - 9 (MR) | Pressed | Below 1 Ω |
| Not pressed | 10 kΩ or higher |
| 3. INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/ Memory) |
![]() |
Inspect the outer mirror switch assembly.
Select "L" on the left/right adjustment switch.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition | |
| 3 (M+) - 2 (E) | UP | Pressed | 100 Ω |
| Not pressed | 10 kΩ or higher | ||
| DOWN | Pressed | 470 Ω | |
| Not pressed | 10 kΩ or higher | ||
| LEFT | Pressed | 800 Ω | |
| Not pressed | 10 kΩ or higher | ||
| RIGHT | Pressed | 250 Ω | |
| Not pressed | 10 kΩ or higher | ||
| 1 (MSW) - 2 (E) | L switch | Pressed | 100 Ω |
| Not pressed | 10 kΩ or higher | ||
Select "R" on the left/right adjustment switch.
Using an ohmmeter, measure the resistance and check the results in accordance with the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition | |
| 3 (M+) - 2 (E) | UP | Pressed | 100 Ω |
| Not pressed | 10 kΩ or higher | ||
| DOWN | Pressed | 470 Ω | |
| Not pressed | 10 kΩ or higher | ||
| LEFT | Pressed | 800 Ω | |
| Not pressed | 10 kΩ or higher | ||
| RIGHT | Pressed | 250 Ω | |
| Not pressed | 10 kΩ or higher | ||
| 1 (MSW) - 2 (E) | R switch | Pressed | Below 1 Ω |
| Not pressed | 10 kΩ or higher | ||
Inspect the retract switch.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 8 (MF) - 4 (E2) | Pressed | Below 1 Ω |
| Not pressed | 10 kΩ or higher |