Home › Vehicle Exterior › WIPER / WASHER › WIPER SWITCH

WIPER SWITCH > INSPECTION

for Preparation Click here



1. INSPECT WIPER SWITCH


E149220E05
  1. Check the resistance.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Front Wiper Switch 
      Tester Connection
      Switch Condition
      Specified Condition
      B-2 (+B) - B-3 (+1)
      MIST
      Below 1 Ω
      B-1 (+S) - B-3 (+1)
      OFF
      Below 1 Ω
      B-1 (+S) - B-3 (+1)
      INT
      Below 1 Ω
      B-2 (+B) - B-3 (+1)
      LO
      Below 1 Ω
      B-2 (+B) - B-4 (+2)
      HI
      Below 1 Ω

      If the result is not as specified, replace the wiper switch.

      Standard Resistance:
      Front Washer Switch 
      Tester Connection
      Switch Condition
      Specified Condition
      A-2 (EW) - A-3 (WF)
      OFF
      10 kΩ or higher
      A-2 (EW) - A-3 (WF)
      ON
      Below 1 Ω

      If the result is not as specified, replace the wiper switch.

      Standard Resistance:
      Rear Wiper and Washer Switch 
      Tester Connection
      Switch Condition
      Specified Condition
      A-2 (EW) - B-5 (WR)
      WASH (Rear wiper switch OFF)
      Below 1 Ω
      A-2 (EW) - B-5 (WR)
      A-2 (EW) - A-7 (+1R)
      OFF
      10 kΩ or higher
      A-2 (EW) - A-6 (C1R)
      INT-LO
      Below 1 Ω
      A-2 (EW) - A-7 (+1R)
      ON-HI
      Below 1 Ω
      A-2 (EW) - B-5 (WR)
      A-2 (EW) - A-7 (+1R)
      A-7 (+1R) - B-5 (WR)
      WASH (Rear wiper switch ON)
      Below 1 Ω

      If the result is not as specified, replace the wiper switch.



  1. Check the intermittent operation.

    1. Connect the positive (+) voltmeter terminal to terminal 3 (+1) of the B connector and the negative (-) voltmeter terminal to terminal 2 (EW) of the A connector.

    2. Connect the positive (+) battery lead to terminal 2 (+B) of the B connector and the negative (-) battery lead to terminals 2 (EW) of the A connector and 1 (+S) of the B connector.

    3. Turn the wiper switch to the INT position.

    4. Connect the positive (+) battery lead to terminal 1 (+S) of the B connector for 5 seconds.



    5. Connect the negative (-) battery lead to terminal 1 (+S) of the B connector. Operate the intermittent wiper relay and check the voltage between terminals 3 (+1) of the B connector and 2 (EW) of the A connector.

      Standard:
      Refer to the illustration below.



      E146261E04

      If the result is not as specified, replace the windshield wiper switch.



  1. Check the operation (front washer).

    1. Turn the wiper switch off.

    2. Connect the positive (+) battery lead to terminal 2 (+B) of the B connector and the negative (-) battery lead to terminals 1 (+S) of the B connector and 2 (EW) of the A connector.



    3. Connect the positive (+) voltmeter terminal to terminal 3 (+1) of the B connector and the negative (-) voltmeter terminal to terminal 2 (EW) of the A connector. Turn the washer switch on and off, and check the voltage between terminals 3 (+1) of the B connector and 2 (EW) of the A connector.

      Standard:
      Refer to the illustration below.



      E106382E12

      If the result is not as specified, replace the windshield wiper switch.