Home › Brake › PARKING BRAKE › PARKING BRAKE PEDAL

PARKING BRAKE PEDAL > INSTALLATION

for Preparation Click here



1. INSTALL PARKING BRAKE CONTROL PEDAL ASSEMBLY


    C154234
  1. Install the control pedal to the body with the 3 nuts.

    Torque:
    13 N*m{ 127 kgf*cm , 9 ft.*lbf }



    C181290
  1. Attach the wire harness clamp to the parking brake control pedal assembly.

  1. Connect the parking brake switch connector.



2. CONNECT NO. 1 PARKING BRAKE CABLE ASSEMBLY


    C155437
  1. Connect the parking brake cable to the control pedal.

  1. Using needle-nose pliers, slowly bend down the claw.

    NOTICE:
    Be careful not to damage the parking brake cable or claw.



    C156829
  1. Install a new clip to the control pedal.



    C154230
  1. Temporarily install the adjustment nut and lock nut.

    HINT:
    The nuts will be tightened to a torque specification in the "Adjust Parking Brake Pedal Travel" procedure.



3. CHECK PARKING BRAKE PEDAL TRAVEL
  1. Firmly depress the parking brake pedal.

  1. Release the parking brake.

  1. Slowly depress the parking brake pedal with a force of approximately 300 N (31 kgf, 67.4 lbf) and count the number of clicks.

    OK:
    6 to 9 clicks



4. ADJUST PARKING BRAKE PEDAL TRAVEL
  1. Depress the parking brake pedal.

  1. Release the parking brake pedal to the original position.



    C154230
  1. Loosen the pedal side No. 1 parking brake cable lock nut.

  1. Turn the pedal side No. 1 parking brake cable adjustment nut until the parking brake pedal travel is correct.

    Standard Parking Brake Pedal Travel:
    Pedal Load
    Click Number
    300 N (31 kgf, 67.4 lbf)
    6 to 9

  1. Using a wrench or equivalent to hold the adjustment nut, tighten the lock nut.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

    NOTICE:
    Pay attention that the adjustment nut does not rotate with the lock nut during tightening.



  1. Additionally, excessive pedal travel can be adjusted on the No. 1 parking brake cable underbody side as follows.

    1. Release the parking brake pedal to the original position.



    2. C159467E02
    3. Loosen the underbody side No. 1 parking brake cable lock nut.

    4. Turn the underbody side No. 1 parking brake cable adjustment nut until the parking brake pedal travel is correct.

      Standard Parking Brake Pedal Travel:
      Pedal Load
      Click Number
      300 N (31 kgf, 67.4 lbf)
      6 to 9

    5. Tighten the underbody side No. 1 parking brake cable lock nut.

      Torque:
      13 N*m{ 127 kgf*cm , 9 ft.*lbf }

      NOTICE:
      Pay attention that the adjustment nut does not rotate with the lock nut during tightening.

  1. Depress to full stroke and release the parking brake pedal 3 or 4 times. Then check the number of clicks when depressing the pedal.

    OK:
    6 to 9 clicks

    If the result is not as specified, adjust the parking brake pedal travel again.

  1. Check whether the parking brake drags or not.
    If the parking brake drags, adjust the shoe clearance.

  1. When operating the parking brake pedal, check that the parking brake pedal indicator light comes on at the first notch.
    If not, adjust the parking brake switch installation position.



5. INSTALL NO. 1 SIDE DEFROSTER NOZZLE DUCT


6. INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY


    B225998
  1. Connect the connector.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. Attach the 2 claws to install the DLC3.

  1. Install the 4 bolts to install the instrument panel airbag.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



7. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LH


    B163883
  1. Attach the 2 claws to install the sensor.



    B229064
  1. Connect the connectors.

  1. Attach the 9 clips and claw to install the finish panel.

  1. Install the 2 <A> bolts.



8. INSTALL HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


    B192511
  1. Connect the hood lock control cable assembly to the hood lock control lever sub-assembly.

  1. Attach the 3 claws to install the hood lock lever



9. INSTALL INSTRUMENT SIDE PANEL LH


    B229058
  1. Attach the 7 claws to install the side panel.



10. INSTALL COWL SIDE TRIM BOARD LH

HINT:
Use the same procedure for both sides.



11. INSTALL FRONT DOOR SCUFF PLATE LH

HINT:
Use the same procedure for both sides.