Home › Brake › PARKING BRAKE › PARKING BRAKE CABLE

PARKING BRAKE CABLE > INSTALLATION

for Preparation Click here



1. INSTALL PARKING BRAKE SHOE LEVER LH


C155125E02
  1. Apply high temperature grease to the parking brake shoe lever.



    C117760E03
  1. Install the parking brake shoe lever to the No. 3 parking brake cable.

    NOTICE:
    Carefully distinguish the parking brake shoe lever RH and LH.



2. INSTALL PARKING BRAKE SHOE LEVER RH

HINT:
Use the same procedure for both sides.



3. INSTALL NO. 2 PARKING BRAKE SHOE ASSEMBLY LH
  1. Apply high temperature grease to the areas of the backing plate that contact the shoe.



    C154249E01
  1. Using SST, install the No. 2 parking brake shoe with the shoe hold down spring pin, compression spring and shoe hold down spring cup.

    SST
    09718-00011  



4. INSTALL NO. 2 PARKING BRAKE SHOE ASSEMBLY RH

HINT:
Use the same procedure for both sides.



5. INSTALL NO. 1 PARKING BRAKE SHOE ASSEMBLY LH
  1. Apply high temperature grease to the areas of the backing plate that contact the shoe.



    C193371E01
  1. Apply high temperature grease to the areas of the shoe adjuster screw set shown in the illustration.

  1. Set the parking brake shoe and shoe adjuster screw set in place.

  1. Connect the tension spring.



    C155124E01
  1. Using SST, install the No. 1 parking brake shoe with the shoe hold down spring pin, compression spring and shoe hold down spring cup.

    SST
    09718-00011  



6. INSTALL NO. 1 PARKING BRAKE SHOE ASSEMBLY RH

HINT:
Use the same procedure for both sides.



7. INSTALL PARKING BRAKE SHOE RETURN SPRING LH


    C191839E01
  1. Using SST, install the shoe return spring.

    SST
    09703-30011  



8. INSTALL PARKING BRAKE SHOE RETURN SPRING RH

HINT:
Use the same procedure for both sides.



9. CHECK PARKING BRAKE INSTALLATION


  1. Check that each part is installed properly.


    C156989E02



10. INSTALL REAR DISC LH


    C178157E02
  1. Align the matchmarks and install the rear disc.



11. INSTALL REAR DISC RH

HINT:
Use the same procedure for both sides.



12. INSTALL NO. 3 PARKING BRAKE CABLE ASSEMBLY


C181308E01
  1. Attach the inner cable end to the carrier assembly and tighten the bolt to the specified torque. The inner cable end will be in position A.

  1. Push the inner cable from the opposite end. The inner cable end that is inside the brake assembly will move inbound as shown in B. From there, it will follow the lever shape and push open the guide spring, as shown in C. Finally, after the inner cable end moves in enough, the guide spring will force the cable end to seat in the final operation location, as shown in D.

  1. After connecting the inner cable end to the brake assembly, push and pull the opposite end of the inner cable 2 or 3 times to confirm that the inner cable end and brake assembly are securely connected.



    C154244
  1. Install the No. 3 parking brake cable to the rear axle carrier with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



  1. Install the No. 3 parking brake cable to the frame with the 4 bolts.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }

    NOTICE:
    Do not bend and twist the parking brake cable.



    C181281E01

  1. Apply MP grease to the areas where the cable contact the intermediate lever.



    C180582
  1. Connect the No. 3 parking brake cable to the intermediate lever.



13. INSTALL NO. 2 PARKING BRAKE CABLE ASSEMBLY



C180575E02

HINT:
The No. 2 parking brake cable bolt locations are symmetric to those of the No. 3 parking brake cable, with the exception of the locations indicated with *A.

  1. Install the No. 2 parking brake cable to the rear axle carrier with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Install the No. 2 parking brake cable to the frame with the 8 bolts.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }

  1. Connect the No. 2 parking brake cable to the intermediate lever.



14. INSTALL NO. 2 CABLE RETAINER


    C156991
  1. Install the retainer with the bolt.

    Torque:
    13 N*m{ 127 kgf*cm , 9 ft.*lbf }



15. INSTALL INTERMEDIATE LEVER TENSION SPRING


    C156990
  1. Install the tension spring.



16. ADJUST PARKING BRAKE SHOE CLEARANCE
  1. Temporarily install the hub nuts.

  1. Remove the hole plug.



    C158874E01
  1. Insert an adjustment tool into the adjustment hole of the disc. Rotate the adjustment wheel in the "X" direction until the shoes are locked. Then rotate the adjustment wheel in the "Y" direction 8 notches.

  1. Check that the disc can be rotated smoothly. If not, rotate the adjustment wheel in the "Y" direction and check again.

  1. Install the hole plug.

  1. Remove the hub nuts.



17. CONNECT REAR DISC BRAKE CYLINDER ASSEMBLY LH


    C158344
  1. Connect the rear disc brake cylinder with the 2 bolts.

    Torque:
    95 N*m{ 969 kgf*cm , 70 ft.*lbf }

    NOTICE:
    1. Do not twist the brake hose.
    2. Make sure that the bolts are free from damage and foreign matter.
    3. Do not overtighten the bolts.



18. CONNECT REAR DISC BRAKE CYLINDER ASSEMBLY RH

HINT:
Use the same procedure for both sides.



19. INSTALL REAR WHEEL LH

Torque:
131 N*m{ 1336 kgf*cm , 97 ft.*lbf }



20. INSTALL REAR WHEEL RH

HINT:
Use the same procedure for both sides.



21. CONNECT NO. 1 PARKING BRAKE CABLE ASSEMBLY


    C155437
  1. Connect the parking brake cable to the control pedal.

  1. Using needle-nose pliers, slowly bend down the claw.

    NOTICE:
    Be careful not to damage the parking brake cable or claw.



    C156829
  1. Install a new clip to the control pedal.



    C154230
  1. Temporarily install the adjustment nut and lock nut.

    HINT:
    The nuts will be tightened to a torque specification in the "Adjust Parking Brake Pedal Travel" procedure.



22. INSTALL NO. 1 PARKING BRAKE CABLE ASSEMBLY



C183663E02

  1. Install the No. 1 parking brake cable to the inside of the vehicle with the 2 bolts (labeled A).

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

  1. Connect the clamp (labeled B) to the No. 1 parking brake cable.

  1. Install the clamp with the nut (labeled C).

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

  1. Install the No. 1 parking brake cable and cable retainer with the bolt (labeled D).

    Torque:
    13 N*m{ 127 kgf*cm , 9 ft.*lbf }

  1. Temporarily install the adjustment nut and lock nut (labeled E).

    NOTICE:
    Do not bend and twist the parking brake cable.

    HINT:
    The nuts will be tightened to a torque specification in the "Adjust Parking Brake Pedal Travel" procedure.



23. INSTALL FRONT NO. 2 EXHAUST PIPE ASSEMBLY


A184928
  1. Install a new gasket and the front No. 2 exhaust pipe sub-assembly to the exhaust manifold LH with 3 new nuts.

    Torque:
    54 N*m{ 554 kgf*cm , 40 ft.*lbf }

  1. Connect the air fuel ratio sensor connector.



    A184927
  1. Connect the front No. 3 exhaust pipe sub-assembly to the exhaust pipe support.

  1. Install a new gasket and the front No. 3 exhaust pipe sub-assembly to the No. 2 exhaust pipe sub-assembly with the 2 bolts and 2 new nuts.

    Torque:
    48 N*m{ 489 kgf*cm , 35 ft.*lbf }



24. SETTLE PARKING BRAKE SHOE AND DISC
  1. Drive the vehicle for approximately 400 m (0.25 miles) under the following conditions.

    1. The vehicle speed is approximately 50 km/h (31 mph) and the vehicle is on a safe, level and dry road.

    2. The parking brake pedal is being depressed with a force of 150 N (15 kgf, 33.7 lbf).

  1. Repeat the procedures above 2 or 3 times.



25. CHECK PARKING BRAKE PEDAL TRAVEL
  1. Firmly depress the parking brake pedal.

  1. Release the parking brake.

  1. Slowly depress the parking brake pedal with a force of approximately 300 N (31 kgf, 67.4 lbf) and count the number of clicks.

    OK:
    6 to 9 clicks



26. ADJUST PARKING BRAKE PEDAL TRAVEL
  1. Depress the parking brake pedal.

  1. Release the parking brake pedal to the original position.



    C154230
  1. Loosen the pedal side No. 1 parking brake cable lock nut.

  1. Turn the pedal side No. 1 parking brake cable adjustment nut until the parking brake pedal travel is correct.

    Standard Parking Brake Pedal Travel:
    Pedal Load
    Click Number
    300 N (31 kgf, 67.4 lbf)
    6 to 9

  1. Using a wrench or equivalent to hold the adjustment nut, tighten the lock nut.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

    NOTICE:
    Pay attention that the adjustment nut does not rotate with the lock nut during tightening.



  1. Additionally, excessive pedal travel can be adjusted on the No. 1 parking brake cable underbody side as follows.

    1. Release the parking brake pedal to the original position.



    2. C159467E02
    3. Loosen the underbody side No. 1 parking brake cable lock nut.

    4. Turn the underbody side No. 1 parking brake cable adjustment nut until the parking brake pedal travel is correct.

      Standard Parking Brake Pedal Travel:
      Pedal Load
      Click Number
      300 N (31 kgf, 67.4 lbf)
      6 to 9

    5. Tighten the underbody side No. 1 parking brake cable lock nut.

      Torque:
      13 N*m{ 127 kgf*cm , 9 ft.*lbf }

      NOTICE:
      Pay attention that the adjustment nut does not rotate with the lock nut during tightening.

  1. Depress to full stroke and release the parking brake pedal 3 or 4 times. Then check the number of clicks when depressing the pedal.

    OK:
    6 to 9 clicks

    If the result is not as specified, adjust the parking brake pedal travel again.

  1. Check whether the parking brake drags or not.
    If the parking brake drags, adjust the shoe clearance.

  1. When operating the parking brake pedal, check that the parking brake pedal indicator light comes on at the first notch.
    If not, adjust the parking brake switch installation position.



27. INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY


    B225998
  1. Connect the connector.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. Attach the 2 claws to install the DLC3.

  1. Install the 4 bolts to install the instrument panel airbag.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



28. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LH


    B163883
  1. Attach the 2 claws to install the sensor.



    B229064
  1. Connect the connectors.

  1. Attach the 9 clips and claw to install the finish panel.

  1. Install the 2 <A> bolts.



29. INSTALL HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


    B192511
  1. Connect the hood lock control cable assembly to the hood lock control lever sub-assembly.

  1. Attach the 3 claws to install the hood lock lever



30. INSTALL INSTRUMENT SIDE PANEL LH


    B229058
  1. Attach the 7 claws to install the side panel.



31. INSTALL COWL SIDE TRIM BOARD LH

HINT:
Use the same procedure for both sides.



32. INSTALL FRONT DOOR SCUFF PLATE LH

HINT:
Use the same procedure for both sides.



33. INSPECT FOR EXHAUST GAS LEAK