Home › Engine / Hybrid System › 3UR-FE ENGINE CONTROL › SFI SYSTEM

DTC    P0550    Power Steering Pressure Sensor Circuit Malfunction

DTC    P0552    Power Steering Pressure Sensor Circuit Low Input

DTC    P0553    Power Steering Pressure Sensor Circuit High Input

for Preparation Click here


DESCRIPTION

The power steering oil pressure sensor is turned ON when a power steering wheel load occurs by turning the steering wheel. The ECM regulates the engine idling RPM according to the voltage output of the sensor.

DTC No.
DTC Detection Condition
Trouble Area
P0550
Power steering oil pressure sensor voltage less than 0.28 V, or more than 4.9 V for 0.5 seconds while engine running.
(1 trip detection logic)
  1. Open or short in power steering oil pressure sensor circuit
  2. Power steering oil pressure sensor
  3. ECM
P0552
Power steering oil pressure sensor voltage less than 0.28 V for 0.5 seconds while engine running.
(1 trip detection logic)
  1. Open or short in power steering oil pressure sensor circuit
  2. Power steering oil pressure sensor
  3. ECM
P0553
Power steering oil pressure sensor voltage more than 4.9 V for 0.5 seconds while engine running.
(1 trip detection logic)
  1. Open or short in power steering oil pressure sensor circuit
  2. Power steering oil pressure sensor
  3. ECM

MONITOR DESCRIPTION

The ECM monitors the sensor voltage and uses this value to regulate the engine idling speed. When the sensor output voltage deviates from the normal operating range, the ECM determines that there is a malfunction in the power steering oil pressure sensor and stores a DTC.

WIRING DIAGRAM


A185019E02


INSPECTION PROCEDURE

HINT:
  1. If other DTCs relating to different systems that have terminal ETHW as the ground terminal are output simultaneously, terminal ETHW may have an open circuit.
  2. Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK HARNESS AND CONNECTOR (ECM - POWER STEERING OIL PRESSURE SENSOR)
A160562E09
  1. Disconnect the ECM connector.

  1. Disconnect the power steering oil pressure sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D30-2 (PSP) - D56-72 (PSP)
    Always
    Below 1 Ω
    D30-1 (VC) - D56-67 (VCV1)
    Always
    Below 1 Ω
    D30-3 (E2) - D56-97 (ETHW)
    Always
    Below 1 Ω
    D30-2 (PSP) or D56-72 (PSP) - Body ground
    Always
    10 kΩ or higher
    D30-1 (VC) or D56-67 (VCV1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.REPLACE POWER STEERING OIL PRESSURE SWITCH
  1. Replace the power steering oil pressure sensor.


NEXT


3.CONFIRM WHETHER DTC OUTPUT RECURS
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.
    Result 
    Result
    Proceed to
    P0550, P0552 and/or P0553 are output
    A
    No DTC is output
    B



B
END
A

REPLACE ECM (Click here)