Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM

ENGINE IMMOBILISER SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK TRANSPONDER KEY ECU ASSEMBLY

B271269E11

  1. Disconnect the H32 transponder key ECU assembly connector.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connector disconnected.


    Tester Connection
    Input/Output
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    Related Data List Item
    H32-1 (+B) - H32-5 (GND)
    Input
    G - W-B
    Battery
    Always
    11 to 14 V
    +B
    H32-2 (IG) - H32-5 (GND)
    Input
    GR - W-B
    Ignition switch signal
    Ignition switch off
    Below 1 V
    IG SW
    Ignition switch ON
    11 to 14 V
    H32-3 (KSW) - H32-5 (GND)
    Input
    LG - W-B
    Unlock warning switch signal
    No key in ignition key cylinder
    10 kΩ or higher
    Key SW/B2780
    Key in ignition key cylinder
    Below 1 Ω
    H32-5 (GND) - Body ground
    -
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    -
    H32-7 (CTY) - Body ground
    Input
    Y - Body ground
    Door courtesy switch (for driver side) signal
    Driver side door closed
    10 kΩ or higher
    -
    Driver side door open
    Below 1 Ω

  3. Reconnect the H32 transponder key ECU assembly connector.

  4. Measure the voltage and check for pulses according to the value(s) in the table below.

    Tester Connection
    Input/Output
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    Related Data List Item
    H32-8 (IND) - H32-5 (GND)
    Output
    V - W-B
    Security indicator signal
    No key in ignition key cylinder, or 20 seconds elapsed after turning ignition switch to ACC or off (immobiliser system set)
    Pulse generation
    Immobiliser
    Key in ignition key cylinder (immobiliser system unset)
    Below 1 V
    H32-9 (D) - H32-5 (GND)
    Input/Output
    B - W-B
    DLC3 communication
    Without communication
    Below 1 V
    -
    During communication
    Pulse generation
    H32-4 (ANT1) - H32-5 (GND)
    Input/Output
    L - W-B
    Transponder key amplifier power source
    No key in ignition key cylinder
    4 to 6 V
    -
    Within 3 seconds of inserting key into ignition key cylinder
    Pulse generation
    (See waveform 1)
    H32-15 (ANT2) - H32-5 (GND)
    Input/Output
    W - W-B
    Transponder key amplifier communication signal
    No key in ignition key cylinder
    4 to 6 V
    -
    Within 3 seconds of inserting key into ignition key cylinder
    Pulse generation
    (See waveform 2)
    H32-12 (EFII) - H32-5 (GND)
    Output
    SB - W-B
    ECM input signal
    Ignition switch off
    11 to 14 V
    -
    Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal
    Pulse generation
    (See waveform 3)
    H32-13 (EFIO) - H32-5 (GND)
    Input
    Y - W-B
    ECM output signal
    Ignition switch off
    Below 1 V
    -
    Ignition switch ON
    Pulse generation
    (See waveform 4)



  5. Using an oscilloscope, check the waveform.



    1. Waveform 1 (Reference)


      B329909E01

      Tester Connection
      H32-4 (ANT1) - H32-5 (GND)
      Tool Setting
      2 V/DIV., 500 ms./DIV.
      Condition
      Within 3 seconds of inserting key into ignition key cylinder



    2. Waveform 2 (Reference)


      B329910E01

      Tester Connection
      H32-15 (ANT2) - H32-5 (GND)
      Tool Setting
      2 V/DIV., 500 ms./DIV.
      Condition
      Within 3 seconds of inserting key into ignition key cylinder



    3. Waveform 3 (Reference)


      B325134E02


      Text in Illustration 
      *a
      Approximately 160 ms
      *b
      Approximately 270 ms
      Tester Connection
      H32-12 (EFII) - H32-5 (GND)
      Tool Setting
      2 V/DIV., 500 ms./DIV.
      Condition
      Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal



    4. Waveform 4 (Reference)


      B333259E02


      Text in Illustration 
      *a
      Approximately 160 ms
      *b
      Approximately 270 ms
      Tester Connection
      H32-13 (EFIO) - H32-5 (GND)
      Tool Setting
      2 V/DIV., 500 ms./DIV.
      Condition
      Ignition switch ON


CHECK ECM

A186167E01


Tester Connection
Input/Output
Wiring Color
Terminal Description
Condition
Specified Condition
Related Data List Item
D56-81 (E1) - Body ground
-
BR - Body ground
Ground
Always
Below 1 Ω
-
D56-43 (E01) - Body ground
-
W-B - Body ground
Ground
Always
Below 1 Ω
-
D56-42 (E02) - Body ground
-
BR - Body ground
Ground
Always
Below 1 Ω
-
A27-1 (BATT) - D56-81 (E1)
Input
L - BR
+B power supply
Always
11 to 14 V
-
A27-2 (+B2) - D56-81 (E1)
Input
GR - BR
+B power supply
Ignition switch ON
11 to 14 V
-
A27-3 (+B) - D56-81 (E1)
Input
GR - BR
+B power supply
Ignition switch ON
11 to 14 V
-
A27-29 (IMO) - D56-81 (E1)
Input
P - BR
Transponder key ECU assembly communication input
Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal
Pulse generation
(See waveform 1)
-
A27-40 (IMI) - D56-81 (E1)
Output
B - BR
Transponder key ECU assembly communication output
Ignition switch off
Below 1 V
-
Ignition switch ON
Pulse generation
(See waveform 2)
-


  1. Using an oscilloscope, check the waveform.



    1. Waveform 1 (Reference)


      B333258E02


      Text in Illustration 
      *a
      Approximately 160 ms
      *b
      Approximately 270 ms
      Tester Connection
      A27-29 (IMO) - D56-81 (E1)
      Tool Setting
      2 V/DIV., 500 ms./DIV.
      Condition
      Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal



    2. Waveform 2 (Reference)


      B333259E02


      Text in Illustration 
      *a
      Approximately 160 ms
      *b
      Approximately 270 ms
      Tester Connection
      A27-40 (IMI) - D56-81 (E1)
      Tool Setting
      2 V/DIV., 500 ms./DIV.
      Condition
      Ignition switch ON