Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM

DTC    C1249/49    Open in Stop Light Switch Circuit

for Preparation Click here


DESCRIPTION

The skid control ECU detects the brake operating conditions through a signal transmitted by the stop light switch. The skid control ECU incorporates an open circuit detection circuit.

DTC Code
DTC Detection Condition
Trouble Area
C1249/49
When one of following conditions is met:
  1. When voltage of STP2 pin is detected to be outside range of 1.4 to 2.2 V for 1 second.
  2. When stop light switch signal and stop light control relay drive signal do not match for 1.2 seconds.
  3. When pressure sensor signal indicates pressure increase, but stop light switch signal does not change.
  4. While driving at speed of 20 km/h (12 mph) or more, stop light switch is ON for more than 6 minutes.
  5. While vehicle is accelerated to higher than 40 km/h (24.9 mph) and then decelerated to less than 3 km/h (1.9 mph), stop light switch signal change from OFF to ON is not detected (4 trip detection logic).
  1. ECU-IG1 fuse
  2. STOP fuse
  3. Stop light control relay
  4. Stop light switch
  5. Stop light switch circuit
  6. VSC actuator (skid control ECU)

WIRING DIAGRAM


C162016E08


INSPECTION PROCEDURE

NOTICE:
When replacing the VSC actuator assembly, perform zero point calibration (Click here).

1.INSPECT FUSE (STOP)


    C160102E01
  1. Remove the STOP fuse from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    STOP fuse
    Always
    Below 1 Ω



NG
CHECK FOR SHORTS IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE
OK


2.INSPECT STOP LIGHT CONTROL RELAY (BRK NO. 1, BRK NO. 2)


    C160102E03
  1. Remove the stop light control relays (BRK NO. 1 and BRK NO. 2) from the engine room relay block.



    A087121E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for BRK NO. 1 
    Tester Connection
    Condition
    Specified Condition
    3 - 4
    When battery voltage is not applied to terminals 1 and 2
    Below 1 Ω
    3 - 5
    When battery voltage is not applied to terminals 1 and 2
    10 kΩ or higher
    3 - 4
    When battery voltage is applied to terminals 1 and 2
    10 kΩ or higher
    3 - 5
    When battery voltage is applied to terminals 1 and 2
    Below 1 Ω
    for BRK NO. 2 
    Tester Connection
    Condition
    Specified Condition
    3 - 4
    When battery voltage is not applied to terminals 1 and 2
    Below 1 Ω
    When battery voltage is applied to terminals 1 and 2
    10 kΩ or higher



NG
REPLACE STOP LIGHT CONTROL RELAY
OK


3.INSPECT STOP LIGHT SWITCH ASSEMBLY


    C108891E12
  1. Disconnect the A4 switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    Pin not pushed
    Below 1 Ω
    Pin pushed
    10 kΩ or higher



NG
REPLACE STOP LIGHT SWITCH ASSEMBLY (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (BATTERY - SKID CONTROL ECU)


    C240470E03
  1. Disconnect the A19 ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A19-6 (STP2) - Body ground
    Brake pedal depressed
    8 to 14 V
    A19-6 (STP2) - Body ground
    Brake pedal released
    Below 4.0 V
    A19-38 (STP) - Body ground
    Brake pedal depressed
    8 to 14 V
    A19-38 (STP) - Body ground
    Brake pedal released
    Below 4.0 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE VSC ACTUATOR ASSEMBLY (Click here)