Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM

VEHICLE STABILITY CONTROL SYSTEM > TERMINALS OF ECU

for Preparation Click here



SKID CONTROL ECU

C240418E02


Terminal No. (Symbol)
Terminal Description
16 (GND1)
Skid control ECU ground
15 (STPO)
Stop light control relay (BRK NO. 1) signal input
14 (PKB2)
Parking brake switch signal input
13 (CANL)
Vehicle CAN communication line
12 (CANH)
Vehicle CAN communication line
11 (EXI2)*
Center differential lock detection switch signal input
10 (D/G)
Diagnosis tester communication line
9
No pin
8 (IG1)
IG1 power supply
7 (TS)
Sensor check input
6 (STP2)
Stop light switch and stop light control relay (BRK NO. 1) signal input
5
No pin
4
No pin
3 (SP1)
Vehicle speed pulse signal output
2
No pin
1 (+BM)
Motor relay power supply
31 (BST)
Brake booster solenoid ground
30 (PIM)
Pedal stroke sensor (Delta S sensor) input line
29 (GYAW)
Yaw rate sensor ground
28
No pin
27 (E3)
Pedal stroke sensor (Delta S sensor) ground
26 (VCP)
Pedal stroke sensor (Delta S sensor) power source
25
No pin
24 (PSNO)
Brake booster micro switch (Normal Open) signal input
23 (PSNC)
Brake booster micro switch (Normal Close) signal input
22 (VYS)
Yaw rate sensor power source
21 (STS)
Brake booster micro switch power source
20
No pin
19 (SS2)
Yaw rate sensor signal line
18 (SS1)
Yaw rate sensor signal line
17 (BSTP)
Brake booster solenoid power source
47
No pin
46 (FL-)
Front wheel LH speed signal line
45 (FL+)
Front wheel LH speed signal line
44 (BSW)
Stop light control relay (BRK NO. 2) drive input
43 (RR+)
Rear wheel RH speed signal line
42 (RR-)
Rear wheel RH speed signal line
41
No pin
40 (PSOO)
Brake booster micro switch signal output
39
No pin
38 (STP)
Stop light switch signal input
37 (RL-)
Rear wheel LH speed signal line
36 (RL+)
Rear wheel LH speed signal line
35
No pin
34 (FR+)
Front wheel RH speed signal line
33 (FR-)
Front wheel RH speed signal line
32 (+BS)
Solenoid relay power supply
  1. *: for 4WD

CHECK SKID CONTROL ECU

C240419E01

  1. Disconnect the A19 ECU connector.

  2. Measure the voltage or resistance according to the value(s) in the table below.

    HINT:
    1. Voltage cannot be measured with the connector connected to the skid control ECU as the connector is watertight.
    2. *1: for 4WD
    3. *2: for 2WD


    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A19-16 (GND1) - Body ground
    W-B - Body ground
    Skid control ECU ground
    Always
    Below 1 Ω
    A19-15 (STPO) - Body ground
    BR - Body ground
    Stop light control relay (BRK NO. 1) signal input
    Ignition switch ON
    11 to 14 V
    A19-14 (PKB2) - Body ground
    LG - Body ground
    Parking brake switch signal input
    Parking brake switch ON
    Below 1 Ω
    A19-13 (CANL) - A19-12 (CANH)
    W - B
    CAN BUS
    Always
    54 to 69 Ω
    A19-11 (EXI2) - Body ground*1
    GR - Body ground
    Center differential lock detection switch signal input (4WD)
    Center differential lock detection switch ON
    Below 1 Ω
    A19-10 (D/G) - H19-7 (SIL)
    P - BE
    Diagnosis tester communication line
    Always
    Below 1 Ω
    A19-8 (IG1) - Body ground
    V - Body ground
    IG1 power supply
    Ignition switch ON
    11 to 14 V
    A19-7 (TS) - H19-12 (TS)
    W - G
    Sensor check input
    Always
    Below 1 Ω
    A19-6 (STP2) - Body ground
    GR - Body ground
    Stop light switch and stop light control relay (BRK NO. 1) signal input
    Brake pedal depressed
    8 to 14 V
    Brake pedal released
    Below 1.5 V
    A19-1 (+BM) - Body ground
    L - Body ground
    Motor relay power supply
    Always
    11 to 14 V
    A19-31 (BST) - A19-17 (BSTP)
    B - V
    Brake booster solenoid ground
    Always
    1 to 2 Ω
    A19-30 (PIM) - A19-27 (E3)
    R - BE
    Pedal stroke sensor (Delta S sensor) input line
    Always
    4 to 8 kΩ
    A19-29 (GYAW) - O12-5 (GYAW)*1
    P - G
    Yaw rate sensor ground
    Always
    Below 1 Ω
    A19-29 (GYAW) - O11-5 (GYAW)*2
    A19-27 (E3) - Body ground
    BE - Body ground
    Pedal stroke sensor (Delta S sensor) ground
    Always
    10 kΩ or higher
    A19-26 (VCP) - A19-27 (E3)
    G - BE
    Pedal stroke sensor (Delta S sensor) power source
    Always
    150 to 200 Ω
    A19-24 (PSNO) - A19-21 (STS)
    LG - SB
    Brake booster micro switch (Normal Open) signal input
    Brake pedal depressed
    Below 1 Ω
    A19-23 (PSNC) - A19-21 (STS)
    L - SB
    Brake booster micro switch (Normal Close) signal input
    Always
    Below 1 Ω
    A19-22 (VYS) - O12-3 (VYS)*1
    R - R
    Yaw rate sensor power source
    Always
    Below 1 Ω
    A19-22 (VYS) - O11-3 (VYS)*2
    A19-21 (STS) - A19-23 (PSNC)
    SB - L
    Brake booster micro switch power source
    Always
    Below 1 Ω
    A19-19 (SS2) - O12-1 (YAW2)*1
    W - W
    Yaw rate sensor signal line
    Always
    Below 1 Ω
    A19-19 (SS2) - O11-1 (YAW2)*2
    A19-18 (SS1) - O12-2 (YAW1)*1
    B - B
    Yaw rate sensor signal line
    Always
    Below 1 Ω
    A19-18 (SS1) - O11-2 (YAW1)*2
    A19-17 (BSTP) - A19-31 (BST)
    V - B
    Brake booster solenoid power source
    Always
    1 to 2 Ω
    A19-46 (FL-) - z4-1
    LG - B
    Front wheel LH speed signal line
    Always
    Below 1 Ω
    A19-45 (FL+) - z4-2
    V - W
    Front wheel LH speed signal line
    Always
    Below 1 Ω
    A19-44 (BSW) - Body ground
    L - Body ground
    Stop light control relay (BRK NO. 2) drive input
    Ignition switch ON
    11 to 14 V
    A19-43 (RR+) - z5-2
    B - W
    Rear wheel RH speed signal line
    Always
    Below 1 Ω
    A19-42 (RR-) - z5-1
    W - B
    Rear wheel RH speed signal line
    Always
    Below 1 Ω
    A19-40 (PSOO) - A27-36 (STV)
    SB - SB
    Brake booster micro switch signal line
    Always
    Below 1 Ω
    A19-38 (STP) - Body ground
    Y - Body ground
    Stop light switch signal input
    Brake pedal depressed
    8 to 14 V
    Brake pedal released
    Below 1.5 V
    A19-37 (RL-) - z6-1
    P - B
    Rear wheel LH speed signal line
    Always
    Below 1 Ω
    A19-36 (RL+) - z6-2
    L - W
    Rear wheel LH speed signal line
    Always
    Below 1 Ω
    A19-34 (FR+) - z3-2
    BE - W
    Front wheel RH speed signal line
    Always
    Below 1 Ω
    A19-33 (FR-) - z3-1
    G - B
    Front wheel RH speed signal line
    Always
    Below 1 Ω
    A19-32 (+BS) - Body ground
    R - Body ground
    Solenoid relay power supply
    Always
    11 to 14 V