Home › Suspension › SUSPENSION CONTROL › AIR SUSPENSION SYSTEM (w/o AVS)

AIR SUSPENSION SYSTEM (w/o AVS) > TERMINALS OF ECU

for Preparation Click here



CHECK SUSPENSION CONTROL ECU

E158724E02

  1. Measure the voltage and resistance according to the value(s) in the table below.

    Standard 
    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    O19-1 (SLEX) - O19-22 (GND)
    V - W-B
    Exhaust solenoid valve
    Ignition switch ON
    Below 1.0 V
    Engine idling, button of height control switch is pushed from "UP" to "DOWN"
    9 V or more
    O19-3 (SLRR) - O19-22 (GND)
    B - W-B
    Height control valve (Leveling solenoid valve)
    Ignition switch ON
    Below 1.0 V
    Engine idling, button of height control switch is pushed from "DOWN" to "UP"
    9 V or more
    O19-4 (SLRL) - O19-22 (GND)
    BE - W-B
    Height Control Valve (Gate solenoid valve)
    Ignition switch ON
    Below 1.0 V
    Engine idling, button of height control switch is pushed from "DOWN" to "UP"
    9 V or more
    O19-5 (RC) - O19-22 (GND)
    LG - W-B
    Suspension control relay
    Ignition switch ON
    Below 1.0 V
    Engine idling, button of height control switch is pushed from "DOWN" to "UP"
    9 V or more
    O19-10 (IG) - O19-22 (GND)
    GR - W-B
    IG power supply
    Ignition switch ON
    10 to 14 V
    O19-12 (TD) - O19-22 (GND)
    L - W-B
    Height control mode select switch
    Ignition switch ON, Height control select switch pushed (ON)
    Below 1.5 V
    Ignition switch ON, Height control select switch released (OFF)
    10 to 14 V
    O19-13 (UPSW) - O19-22 (GND)
    Y - W-B
    Height control switch (UP)
    Ignition switch ON, "UP" button of height control switch pushed in
    Below 1.5 V
    Ignition switch ON, "UP" button of height control switch released
    10 to 14 V
    O19-14 (SBR2) - O19-22 (GND)
    L - W-B
    Height control sensor RH power source
    Ignition switch ON
    4.5 to 5.5 V
    O19-15 (SBL2) - O19-22 (GND)
    LG - W-B
    Height control sensor LH power source
    Ignition switch ON
    4.5 to 5.5 V
    O19-16 (SHRR) - O19-18 (SGR2)
    R - BR
    Height control sensor RH
    Ignition switch ON
    0.5 to 4.5 V
    Engine idling, vehicle height is changed from "HIGH" to "NORMAL" by pressing the height control switch
    2.4 to 2.7 V
    O19-17 (SHRL) - O19-19 (SGL2)
    Y - V
    Height control sensor LH
    Ignition switch ON
    0.5 to 4.5 V
    Engine idling, vehicle height is changed from "HIGH" to "NORMAL" by pressing the height control switch
    2.4 to 2.7 V
    O19-18 (SGR2) - O19-22 (GND)
    BR - W-B
    Height control sensor RH ground
    Always
    Below 1.0 Ω
    O19-19 (SGL2) - O19-22 (GND)
    V - W-B
    Height control sensor LH ground
    Always
    Below 1.0 Ω
    O19-20 (RM+) - O19-22 (GND)
    G - W-B
    Motor lock (+)
    Engine idling, vehicle height changes from "NORMAL" to "HIGH" by pressing the height control switch (While height control compressor assembly is working).
    Below 1.0 Ω
    O19-21 (RM-) - Body ground
    P - Body ground
    Motor lock (-)
    Always
    Below 1.0 Ω
    O19-22 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1.0 Ω
    O19-24 (B) - O19-22 (GND)
    SB - W-B
    +B power supply
    Always
    10 to 14 V
    O19-25 (BAT) - O19-22 (GND)
    SB - W-B
    +B power supply
    Always
    10 to 14 V
    O19-28 (CANL) - O19-22 (GND)
    W - W-B
    CAN communication line
    Ignition switch ON
    Pulse generation
    (See waveform 1)
    O19-29 (CANH) - O19-22 (GND)
    B - W-B
    CAN communication line
    Ignition switch ON
    Pulse generation
    (See waveform 2)
    O19-32 (DNSW) - O19-22 (GND)
    GR - W-B
    Height control switch (DOWN)
    Ignition switch ON, "DOWN" button of height control switch pushed in
    Below 1.5 V
    Ignition switch ON, "DOWN" button of height control switch released
    10 to 14 V
    If the result is not as specified, the ECU may have a malfunction.



  2. C123996E01
  3. Using an oscilloscope, check the waveform 1.
    Reference 
    Terminal No. (Symbol)
    O19-28 (CANL) - O19-22 (GND)
    Tool Setting
    1 V/DIV, 10 μs/DIV
    Vehicle Condition
    Ignition switch ON, Engine stopped



  4. C123997E01
  5. Using an oscilloscope, check the waveform 2.
    Reference 
    Terminal No. (Symbol)
    O19-29 (CANH) - O19-22 (GND)
    Tool Setting
    1 V/DIV, 10 μs/DIV
    Vehicle Condition
    Ignition switch ON, Engine stopped