Home › Suspension › SUSPENSION CONTROL › AIR SUSPENSION SYSTEM (w/ AVS)

AIR SUSPENSION SYSTEM (w/ AVS) > TERMINALS OF ECU

for Preparation Click here



CHECK SUSPENSION CONTROL ECU

E158723E02

  1. Measure the voltage and resistance according to the value(s) in the table below.

    Standard 
    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    O16-7 (SLRL) - O17-5 (GND)
    BE - W-B
    Height control valve (Gate solenoid valve)
    Ignition switch ON
    Below 1.0 V
    Engine idling, button of height control switch is pushed from "DOWN" to "UP"
    9 V or more
    O16-8 (SLEX) - O17-5 (GND)
    V - W-B
    Exhaust valve
    Ignition switch ON
    Below 1.0 V
    Engine idling, button of height control switch is pushed from "UP" to "DOWN"
    9 V or more
    O16-9 (SLRR) - O17-5 (GND)
    B - W-B
    Height control valve (Leveling solenoid valve)
    Ignition switch ON
    Below 1.0 V
    Engine idling, button of height control switch is pushed from "DOWN" to "UP"
    9 V or more
    O16-18 (RC) - O17-5 (GND)
    LG - W-B
    Suspension control relay
    Ignition switch ON
    Below 1.0 V
    Engine idling, button of height control switch is pushed from "DOWN" to "UP"
    9 V or more
    O16-19 (SGR2) - O17-5 (GND)
    BR - W-B
    Rear height control sensor RH ground
    Always
    Below 1.0 Ω
    O16-20 (SBR2) - O16-19 (SGR2)
    L - BR
    Height control sensor RH power source
    Ignition switch ON
    4.5 to 5.5 V
    O16-21 (SGL2) - O17-5 (GND)
    V - W-B
    Height control sensor LH ground
    Always
    Below 1.0 Ω
    O16-22 (SBL2) - O16-21 (SGL2)
    LG - V
    Height control sensor LH power source
    Ignition switch ON
    4.5 to 5.5 V
    O16-23 (SHRL) - O16-21 (SGL2)
    Y - V
    Height control sensor LH
    Ignition switch ON
    0.5 to 4.5 V
    Engine idling, vehicle height is changed from "HIGH" to "NORMAL" by pressing the height control switch
    2.4 to 2.7 V
    O16-24 (SHRR) - O16-19 (SGR2)
    R - BR
    Height control sensor RH
    Ignition switch ON
    0.5 to 4.5 V
    Engine idling, vehicle height is changed from "HIGH" to "NORMAL" by pressing the height control switch
    2.4 to 2.7 V
    O16-25 (RM+) - O17-5 (GND)
    G - W-B
    Motor lock (+)
    Engine idling, vehicle height changes from "NORMAL" to "HIGH" by pressing the height control switch (While height control compressor assembly is working).
    Below 1.0 Ω
    O16-26 (RM-) - O17-5 (GND)
    P - W-B
    Motor lock (-)
    Always
    Below 1.0 Ω
    O17-5 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1.0 Ω
    O17-6 (B) - O17-5 (GND)
    SB - W-B
    +B power supply
    Ignition switch ON
    10 to 14 V
    O17-15 (DNSW) - O17-5 (GND)
    GR - W-B
    Height control switch (DOWN)
    Ignition switch ON, "DOWN" button of height control switch pushed in
    Below 1.5 V
    Ignition switch ON, "DOWN" button of height control switch released
    10 to 14 V
    O17-16 (UPSW) - O17-5 (GND)
    Y - W-B
    Height control switch (UP)
    Ignition switch ON, "UP" button of height control switch pushed in
    Below 1.5 V
    Ignition switch ON, "UP" button of height control switch released
    10 to 14 V
    O17-18 (SBR) - O17-22 (SGR)
    G - V
    Front acceleration sensor RH power source
    Ignition switch ON
    4.5 to 5.5 V
    O17-21 (SBR3) - O18-25 (SGR3)
    P - B
    Front acceleration sensor LH power source
    Ignition switch ON
    4.5 to 5.5 V
    O17-22 (SGR) - Body ground
    V - Body ground
    Front acceleration sensor RH ground
    Always
    Below 1.0 Ω
    O17-24 (TD) - O17-5 (GND)
    L - W-B
    Height control mode select switch
    Ignition switch ON, Height control select switch ON
    Below 1.5 V
    Ignition switch ON, Height control select switch OFF
    10 to 14 V
    O18-1 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1.0 Ω
    O18-2 (TSW2) - O17-5 (GND)
    V - W-B
    Absorber control switch (SPORT)
    Ignition switch ON, Absorber control switch select "NORMAL"
    10 to 14 V
    Ignition switch ON, Absorber control switch select "SPORT"
    Below 1.5 V
    O18-3 (TSW1) - O17-5 (GND)
    R - W-B
    Absorber control switch (COMFORT)
    Ignition switch ON, Absorber control switch select "NORMAL"
    10 to 14 V
    Ignition switch ON, Absorber control switch select "COMFORT"
    Below 1.5 V
    O18-10 (IG) - O18-1 (GND)
    R - W-B
    IG power supply
    Ignition switch ON
    10 to 14 V
    O18-25 (SGR3) - O17-5 (GND)
    B - W-B
    Front acceleration sensor LH ground
    Always
    Below 1.0 Ω
    O18-27 (SGFR) - O17-22 (SGR)
    Y - V
    Front acceleration sensor RH
    Always
    0.5 to 4.5 V
    O18-28 (SGRR) - O18-25 (SGR3)
    BE - B
    Front acceleration sensor LH
    Always
    0.5 to 4.5 V
    O18-29 (CANL) - O18-1 (GND)
    W - W-B
    CAN communication line
    Ignition switch ON
    Pulse generation
    (See waveform 1)
    O18-30 (CANH) - O18-1 (GND)
    B - W-B
    CAN communication line
    Ignition switch ON
    Pulse generation
    (See waveform 2)
    If the result is not as specified, the ECU may have a malfunction.



  2. C123996E01
  3. Using an oscilloscope, check the waveform 1.
    Reference 
    Terminal No. (Symbol)
    O18-29 (CANL) - O18-1 (GND)
    Tool Setting
    1 V/DIV, 10 μs/DIV
    Vehicle Condition
    Ignition switch ON, Engine stopped



  4. C123997E01
  5. Using an oscilloscope, check the waveform 2.
    Reference 
    Terminal No. (Symbol)
    O18-30 (CANH) - O18-1 (GND)
    Tool Setting
    1 V/DIV, 10 μs/DIV
    Vehicle Condition
    Ignition switch ON, Engine stopped