Home › Suspension › SUSPENSION CONTROL › AIR SUSPENSION SYSTEM (w/ AVS)

DTC    C1782    Power Source Voltage Malfunction

for Preparation Click here


DESCRIPTION

  1. This circuit provides power to operate the suspension control ECU.
  2. The suspension control ECU, controlling the air suspension system, is activated when the ignition switch is turned ON. The main relay inside the ECU is activated after 2 seconds and the system is operated by +B power source.

DTC Code
Detection Condition
Trouble Area
C1782
Terminal IG or B voltage is 10 V or less, or 16 V or more for 0.5 seconds
  1. Battery
  2. Wire harness or connector
  3. Suspension control ECU

WIRING DIAGRAM


C179535E05


INSPECTION PROCEDURE

NOTICE:
  1. After replacing the suspension control ECU, perform registration (Click here).
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.READ VALUE USING INTELLIGENT TESTER (POWER SOURCE VOLTAGE)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON, and turn the intelligent tester on.

  1. Enter the following menus: Chassis / Air suspension / Data List.

    Air Suspension 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    +B Power Source Voltage
    ECU power supply voltage / min.: 0 V, max.: 25.5 V
    Actual battery power supply voltage: 11 to 14 V
    -
    IG Power Source Voltage
    ECU power supply voltage / min.: 0 V, max.: 25.5 V
    Actual ECU power supply voltage: 11 to 14 V
    -

    Standard voltage:
    11 to 14 V

    Result 
    Result
    Proceed to
    NG
    A
    OK (When troubleshooting according to the Problem Symptoms Table)
    B
    OK (When troubleshooting according to the DTC Chart)
    C



B
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

C
USE SIMULATION METHOD TO CHECK (Click here)
A


2.INSPECT FUSE (AIR SUS, AIR SUS NO. 2, AIR SUS IG)


    E160630E17
  1. Remove the AIR SUS and AIR SUS No. 2 fuses from the engine room relay block.

  1. Remove the AIR SUS IG fuse from the cowl side junction block LH.

  1. Measure the resistance of the AIR SUS, AIR SUS No. 2 and AIR SUS IG fuses.

    Standard Resistance:
    Fuse
    Condition
    Specified Condition
    AIR SUS
    Always
    Below 1 Ω
    AIR SUS No. 2
    Always
    Below 1 Ω
    AIR SUS IG
    Always
    Below 1 Ω

  1. Reinstall the AIR SUS, AIR SUS No. 2 and AIR SUS IG fuses.



NG
REPLACE FUSE
OK


3.CHECK BATTERY VOLTAGE


    C241570E02
  1. Disconnect the O16 ECU connectors.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    O16-3 (B) - Body ground
    Always
    11 to 14 V
    O16-1 (IG) - Body ground
    Ignition switch ON
    11 to 14 V



NG
BATTERY VOLTAGE IS LOW OR CHARGING SYSTEM HAS MALFUNCTION
OK


4.CHECK FOR DTC
  1. Clear the DTC (Click here).

  1. Check for DTC (Click here).
    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
REPLACE SUSPENSION CONTROL ECU (Click here)
A

END