Home › Suspension › SUSPENSION CONTROL › AIR SUSPENSION SYSTEM (w/ AVS)

DTC    C1792    Height Control Switch Circuit (Test Mode DTC)

for Preparation Click here


DESCRIPTION

Vehicle height can be chosen by pressing the height control switch.
By pressing the "UP" side, vehicle height goes up.
By pressing the "DOWN" side, vehicle height goes down.

DTC Code
Detection Condition
Trouble Area
C1792
Height control switch signal does not change.
  1. Height control switch (No. 1 absorber control switch)
  2. Wire harness or connector
  3. Suspension control ECU

HINT:
This DTC is output only when the sensor signal check is done.


WIRING DIAGRAM


C180262E05


INSPECTION PROCEDURE

NOTICE:
After replacing the suspension control ECU, perform registration (Click here).

1.READ VALUE USING INTELLIGENT TESTER (HEIGHT CONTROL SWITCH)
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON, and turn the intelligent tester on.

  1. Enter the following menus: Chassis / Air suspension / Data List.

    Air Suspension 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Height Control Switch(Up)
    Height control switch (Up) / ON or OFF
    ON: Height control switch "UP" button pressed
    OFF: -
    -
    Height Control Switch(Down)
    Height control switch (Down) / ON or OFF
    ON: Height control switch "DOWN" button pressed
    OFF: -
    -

  1. Check that the value displayed on the intelligent tester changes by pressing the height control switch "UP" or "DOWN".

    OK:
    Height control switch value changes.

    Result 
    Result
    Proceed to
    NG
    A
    OK (When troubleshooting according to the Problem Symptoms Table)
    B
    OK (When troubleshooting according to the DTC Chart)
    C



B
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

C
USE SIMULATION METHOD TO CHECK (Click here)
A


2.INSPECT HEIGHT CONTROL SWITCH
  1. Turn the ignition switch off.



    C179509E01
  1. Remove the height control switch.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    4 (LSW) - 6 (E)
    Down operation
    Below 1 Ω
    4 (LSW) - 6 (E)
    Up operation
    10 kΩ or higher
    5 (HSW) - 6 (E)
    Down operation
    10 kΩ or higher
    5 (HSW) - 6 (E)
    Up operation
    Below 1 Ω



NG
REPLACE NO. 1 ABSORBER CONTROL SWITCH
OK


3.CHECK HARNESS AND CONNECTOR (HEIGHT CONTROL SWITCH - ECU AND BODY GROUND)


    C241572E02
  1. Disconnect the O16 ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H72-5 (HSW) - O16-15 (UPSW)
    Always
    Below 1 Ω
    H72-4 (LSW) - O16-14 (DNSW)
    Always
    Below 1 Ω
    H72-6 (E) - Body ground
    Always
    Below 1 Ω
    H72-5 (HSW) or O16-15 (UPSW) - Body ground
    Always
    10 kΩ or higher
    H72-4 (LSW) or O16-14 (DNSW) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE SUSPENSION CONTROL ECU (Click here)