Home › Suspension › SUSPENSION CONTROL › AIR SUSPENSION SYSTEM (w/o AVS)

AIR SUSPENSION SYSTEM (w/o AVS) > DATA LIST / ACTIVE TEST

for Preparation Click here



READ DATA LIST

HINT:
Using a intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may by discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the intelligent tester on.

  4. Enter the following menus: Chassis / Air suspension / Data List.

    Air Suspension 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Stop Light Switch
    Stop light switch / ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    -
    Manual Mode Switch
    Height control mode select switch (Manual) / ON or OFF
    ON: Height control mode select switch ON condition
    OFF: Height control mode select switch OFF condition
    -
    Door Switch
    Door courtesy light switch signal / ON or OFF
    ON: Open each door
    OFF: Close all doors
    -
    Height Control Switch (Up)
    Height control switch (Up) / ON or OFF
    ON: Height control switch "UP" button pressed
    OFF: -
    -
    Height Control Switch (Down)
    Height control switch (Down) / ON or OFF
    ON: Height control switch "DOWN" button pressed
    OFF: -
    -
    Height Position
    Vehicle height condition reading / NORMAL or NOT NOR
    NORMAL: Vehicle height normal
    NOT NOR: Vehicle height not normal
    -
    Height Control
    Vehicle height control condition reading / ON or OFF
    ON: Vehicle height control operating
    OFF: Vehicle height control not operating
    -
    TC Terminal
    TC terminal / ON or OFF
    ON: DTC recorded
    OFF: No DTC recorded
    -
    TS Terminal
    TS terminal / ON or OFF
    ON: During test mode
    OFF: Normal mode
    -
    FR Wheel Speed
    Wheel speed (Front right) reading / min.: 0 km/h (0 mph), max.: 255 km/h (159 mph)
    Actual vehicle speed
    Speed indicated on the speedometer
    FL Wheel Speed
    Wheel speed (Front left) reading / min.: 0 km/h (0 mph), max.: 255 km/h (159 mph)
    Actual vehicle speed
    Speed indicated on the speedometer
    RR Wheel Speed
    Wheel speed (Rear right) reading / min.: 0 km/h (0 mph), max.: 255 km/h (159 mph)
    Actual vehicle speed
    Speed indicated on the speedometer
    RL Wheel Speed
    Wheel speed (Rear left) reading / min.: 0 km/h (0 mph), max.: 255 km/h (159 mph)
    Actual vehicle speed
    Speed indicated on the speedometer
    IG Power Source Voltage
    ECU power supply voltage / min.: 0 V, max.: 25.5 V
    Actual ECU power supply voltage: 11 to 14 V
    -
    +B Power Source Voltage
    +B power source voltage / min.: 0 V, max.: 25.5 V
    Actual battery power supply voltage: 11 to 14 V
    -
    Engine Speed
    Crankshaft position sensor reading / min.: 0 rpm, max.: 25500 rpm
    Actual engine speed
    Engine speed indicated on the tachometer
    Rear Gate Solenoid
    Height control valve solenoid (Gate solenoid valve) / ON or OFF
    ON: Gate solenoid operated
    OFF: Gate solenoid not operated
    -
    Rear Leveling Solenoid
    Height control valve solenoid (Leveling solenoid valve) / ON or OFF
    ON: Leveling solenoid operated
    OFF: Leveling solenoid not operated
    -
    Exhaust Solenoid
    Exhaust solenoid valve / ON or OFF
    ON: Exhaust solenoid valve operated
    OFF: Exhaust solenoid valve not operated
    -
    Motor Relay
    AIR SUS relay / ON or OFF
    ON: Compressor operated
    OFF: Compressor not operated
    -
    Main Relay
    MAIN relay / ON or OFF
    ON: MAIN relay operated
    OFF: MAIN relay not operated
    -
    Number of Trouble Codes
    Number of DTC recorded / min.: 0, max.: 255
    Min.: 0, Max.: 255
    -


PERFORM ACTIVE TEST

HINT:
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the intelligent tester on.

  4. Enter the following menus: Chassis / Air suspension / Active Test.

    Air Suspension 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Rear Wheel Up/Down
    Rear vehicle height/
    UP or DOWN
    -
    Rear Gate Solenoid
    Gate solenoid valve/
    ON or OFF
    Operation sound of solenoid (clicking sound) can be heard
    Rear Leveling Solenoid
    Leveling solenoid valve/
    ON or OFF
    Operation sound of solenoid (clicking sound) can be heard
    Exhaust Solenoid
    Exhaust solenoid valve/
    ON or OFF
    Operation sound of solenoid (clicking sound) can be heard
    Compressor Motor Relay
    AIR SUS relay/
    ON or OFF
    Operation sound of solenoid (clicking sound) can be heard