Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM

THEFT DETERRENT SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)

C172609E07

  1. Disconnect the H1, H3, H4, DB, DC and DD ECU connectors.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Standard 
    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    DB-13 (BECU) - Body ground
    GR - Body ground
    +B power source
    Always
    11 to 14 V
    DA-1 (ALTB) - Body ground
    B - Body ground
    +B power source
    Always
    11 to 14 V
    DD-62 (GND1, GND2) - Body ground
    W-B - Body ground
    Power ground
    Always
    Below 1 Ω
    H4-24 (DCTY) - Body ground
    BR - Body ground
    Driver door courtesy switch
    Driver door closed → open
    10 kΩ or higher → Below 1 Ω
    H3-21 (PCTY) - Body ground
    BE - Body ground
    Front passenger door courtesy switch input
    Front passenger door closed → open
    10 kΩ or higher → Below 1 Ω
    DC-2 (LCTY) - Body ground
    G*1 - Body ground
    B*2 - Body ground
    Rear left door courtesy switch input
    Rear left door closed → open
    10 kΩ or higher → Below 1 Ω
    H3-25 (RRCY) - Body ground
    L - Body ground
    Rear right door courtesy switch input
    Rear right door closed → open
    10 kΩ or higher → Below 1 Ω
    H4-16 (HCTY) - Body ground
    V - Body ground
    Engine hood courtesy switch
    Engine hood closed → open
    10 kΩ or higher → Below 1 Ω
    H1-5 (KSW) - Body ground
    LG - Body ground
    Key unlock warning switch signal
    No key is in ignition key cylinder
    10 kΩ or higher
    Key is in ignition key cylinder
    Below 1 Ω
    *1: w/ Power Seat (Rear No. 2)
    *2: w/o Power Seat (Rear No. 2)
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the H1, H3, H4, DB, DC and DD ECU connectors.

  4. Measure the voltage according to the value(s) in the table below.

    Standard Voltage 
    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    H1-4 (IND) - Body ground
    P - Body ground
    Security indicator signal
    Security indicator illuminates
    (illuminates only for 60 sec. in alarm sounding state (it is blinking when system is in armed state))
    3 to 5 V
    H1-6 (SH) - Body ground
    W - Body ground
    Security horn signal
    Armed state
    Below 1 V
    Security horn is sounding
    (theft deterrent system is in alarm sounding state)
    Pulse generation
    H2-4 (HAZ) - Body ground
    BE - Body ground
    Hazard warning light signal
    Armed state
    Below 1 V
    Security horn is sounding
    (theft deterrent system is in alarm sounding state)
    Pulse generation
    DB-1 (HORN) - Body ground
    V - Body ground
    Horn signal
    (low pitched and high pitched)
    Armed state
    Below 1 V
    Horn is sounding
    11 to 14 V
    If the result is not as specified, the ECU may have a malfunction.


CHECK BACK DOOR ECU

B193574E01

  1. Disconnect the V2 and V3 connectors.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Standard 
    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    V2-1 (BDR) - Body ground
    SB - Body ground
    BDR power supply
    Always
    11 to 14 V
    V2-7 (BECU) - Body ground
    GR - Body ground
    BECU power supply
    Always
    11 to 14 V
    V3-10 (BDCY) - V3-20 (CTYE)
    P - R
    Back door courtesy switch circuit
    Back door is closed
    10 kΩ or higher
    V3-10 (BDCY) - V3-20 (CTYE)
    P - R
    Back door courtesy switch circuit
    Back door is open
    Below 1 Ω
    V3-15 (HSW+) - V3-24 (HSW-)
    B - W
    Back door opener switch signal circuit
    Back door opener switch OFF
    10 kΩ or higher
    V3-15 (HSW+) - V3-24 (HSW-)
    B - W
    Back door opener switch signal circuit
    Back door opener switch ON
    Below 1 Ω
    V2-6 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.