Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM

ENGINE IMMOBILISER SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



READ DATA LIST

HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body / Immobiliser / Data List.

  5. According to the display on the intelligent tester, read the "Data List".

    Immobiliser 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Key SW
    Unlock warning switch signal / ON or OFF
    ON: Key is in ignition key cylinder
    OFF: No key is in ignition key cylinder
    -
    IG SW
    Ignition switch signal / ON or OFF
    ON: Ignition switch ON
    OFF: Ignition switch ACC or OFF
    -
    Immobiliser
    Immobiliser system status / Set or Unset
    Set: No key is in ignition key cylinder
    Unset: Key is in ignition key cylinder
    -
    Permit (Start)
    Permit (start) signal / OK or NG
    OK: Engine start is permitted
    NG: Engine start is not permitted
    -
    Response
    Transponder chip data / OK or NG
    OK: Data OK
    NG: Data error
    -
    Frame Error
    Transponder chip data / OK or NG
    OK: Data OK
    NG: Data error
    -
    Different Serial Number
    Transponder chip data / OK or NG
    OK: Data OK
    NG: Data error
    -
    Different Encrypt Code
    Transponder chip data / OK or NG
    OK: Data OK
    NG: Data error
    -
    Abnormal Status
    Transponder chip data / OK or NG
    OK: Data OK
    NG: Data error
    -
    BCC Malfunction
    Transponder chip signal / OK or NG
    OK: Correct data sent
    NG: Incorrect data sent
    -
    Sub Key
    Sub-key code signal / Reg or Unreg
    Reg: Registered sub-key code is sent
    Unreg: Unmatched sub-key code is sent
    -
    Master Key
    Master key code signal / Reg or Unreg
    Reg: Registered master key code is sent
    Unreg: Unmatched master key code is sent
    -
    Transponder S-code
    Number of registered sub-keys / min.: 0, max.: 15
    Number of registered sub-keys
    -
    Transponder M-code
    Number of registered master keys / min.: 0, max.: 15
    Number of registered master keys
    -
    Reg Code Space Full
    Key registration code memory space full / YES or NO
    NO: Possible to register more key codes
    YES: Cannot register any more key codes
    -
    +B
    +B judgment / Normal or Break
    Normal: Battery supply is normal
    Break: Battery supply is malfunctioning
    -
    Antenna Coil Status
    Antenna coil condition / Normal or Fail
    Normal: Antenna coil is normal
    Fail: Antenna coil is malfunctioning
    -


PERFORM ACTIVE TEST

HINT:
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body / Immobiliser / Active Test.

  5. Perform the Active Test according to the display on the intelligent tester.

    Immobiliser 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Security Indicator
    Security indicator light
    ON or OFF
    -