Home › Suspension › SUSPENSION CONTROL › SUSPENSION CONTROL SYSTEM

SUSPENSION CONTROL SYSTEM > ADJUSTMENT

for Preparation Click here



1. ADJUST STANDARD VEHICLE HEIGHT
  1. Release the parking brake and stabilize the suspensions by pushing up and down on the corners of the vehicle.

  1. Move the shift lever to N and settle the tires by moving the vehicle back and forth.

  1. Start the engine.

  1. On the height control switch, first press "HIGH" to raise the vehicle height, and then change the switch to "LOW" to lower it. Perform this operation one more time.

    NOTICE:
    Release the parking brake and move the shift lever to N.



2. INSPECT TIRE
  1. Check the tires for wear and proper inflation pressure.

    Standard Cold Tire Inflation Pressure:
    Tire Size
    Front
    kPa (kgf/cm2, psi)
    Rear
    kPa (kgf/cm2, psi)
    Spare
    kPa (kgf/cm2, psi)
    P275/65R18
    230 (2.3, 33)
    230 (2.3, 33)
    230 (2.3, 33)
    P275/55R20
    210 (2.1, 30)
    240 (2.4, 35)
    240 (2.4, 35)



    R003031
  1. Using a dial indicator, check the tire runout.

    Tire runout:
    3.0 mm (0.118 in.) or less



3. MEASURE VEHICLE HEIGHT

NOTICE:
Before inspecting the wheel alignment, adjust the vehicle height to the specification.



    C180789E01
  1. Press down on the vehicle several times to stabilize the suspension, and then measure the vehicle height.

    Standard Vehicle Height (Unloaded Vehicle):

    Vehicle Model
    Rear Suspension Type
    Tire Size
    Front A - B
    Rear C - D
    USK60L-GKTSKV
    Coil
    P275/65R18 8JJ
    107.3 mm (4.22 in.)
    28.4 mm (1.12 in.)
    P275/55R20 8JJ
    107.5 mm (4.23 in.)
    28.6 mm (1.13 in.)
    Air
    P275/65R18 8JJ
    106.1 mm (4.18 in.)
    39.1 mm (1.54 in.)
    P275/55R20 8JJ
    106.2 mm (4.18 in.)
    39.3 mm (1.55 in.)
    USK60L-GKTLKV
    Coil
    P275/65R18 8JJ
    108.7 mm (4.28 in.)
    31.6 mm (1.24 in.)
    P275/55R20 8JJ
    108.8 mm (4.28 in.)
    31.8 mm (1.25 in.)
    Air
    P275/65R18 8JJ
    107.7 mm (4.24 in.)
    39.2 mm (1.54 in.)
    P275/55R20 8JJ
    107.9 mm (4.25 in.)
    39.5 mm (1.56 in.)
    USK60L-GKTZKV
    Air + AVS
    P275/55R20 8JJ
    108.6 mm (4.28 in.)
    39.5 mm (1.56 in.)
    USK65L-GKTSKV
    Coil
    P275/65R18 8JJ
    102.9 mm (4.05 in.)
    24.4 mm (0.96 in.)
    P275/55R20 8JJ
    102.9 mm (4.05 in.)
    24.4 mm (0.96 in.)
    Air
    P275/65R18 8JJ
    101.7 mm (4.00 in.)
    34.1 mm (1.34 in.)
    P275/55R20 8JJ
    101.8 mm (4.01 in.)
    34.1 mm (1.34 in.)
    USK65L-GKTLKV
    Coil
    P275/65R18 8JJ
    104.0 mm (4.09 in.)
    26.8 mm (1.06 in.)
    P275/55R20 8JJ
    104.0 mm (4.09 in.)
    26.8 mm (1.06 in.)
    Air
    P275/65R18 8JJ
    103.1 mm (4.06 in.)
    34.2 mm (1.35 in.)
    P275/55R20 8JJ
    103.1 mm (4.06 in.)
    34.3 mm (1.35 in.)
    USK65L-GKTZKV
    Air + AVS
    P275/55R20 8JJ
    104.2 mm (4.10 in.)
    34.4 mm (1.35 in.)

    1. Measuring points

    A:
    Ground clearance of the front drive shaft center

    B:
    Ground clearance of the front adjusting cam bolt center

    C:
    Ground clearance of the rear drive shaft center

    D:
    Ground clearance of the rear lower arm No. 1 adjusting cam bolt center

    If the vehicle height is not as specified, adjust the height by pressing down on the vehicle several times to stabilize the suspension.



4. OPERATE HEIGHT CONTROL SWITCH AND CHECK VEHICLE HEIGHT CHANGE


    C125301E01
  1. Start the engine and change the height control switch from the NORMAL position to the HIGH and LOW positions.
    Check the time until the height adjustment is completed and the amount of change in vehicle height.
    Adjustment Time 
    From operation of height control switch to start of compressor.
    Approx. 2 sec.
    From start of compressor to completion of height adjustment. (NORMAL→HIGH)
    Approx. 25 sec.
    From start of compressor to completion of height adjustment. (NORMAL→LOW)
    Approx. 35 sec.
    Amount of Change in Vehicle Height 
    HIGH position
    30 mm (1.18 in.)
    LOW position
    30 mm (1.18 in.)



    C125411E01
  1. While adjusting vehicle height in the HIGH position, start the engine and change the height control switch from the HIGH position to the NORM position.
    While adjusting vehicle height in the LOW position, start the engine and change the height control switch from the LOW position to the NORM position.
    Check the time until the height adjustment is completed and the amount of change in vehicle height.
    Adjustment Time 
    From operation of height control switch to open of exhaust valve.
    Approx. 2 sec.
    From open of exhaust valve to completion of height adjustment. (HIGH→NORMAL)
    Approx. 35 sec.
    From start of compressor to completion of height adjustment. (LOW→NORMAL)
    Approx. 25 sec.
    Amount of Change in Vehicle Height 
    HIGH position
    30 mm (1.18 in.)
    LOW position
    30 mm (1.18 in.)



5. CHECK CONNECTIONS OF TUBES FOR AIR LEAK
  1. Set the height control switch in the HIGH position and raise the vehicle height.

  1. Stop the engine.



  1. Apply soapy water to the connections of the tubes and check if there is any air leakage.


    C180799E01



6. ADJUST VEHICLE HEIGHT

NOTICE:
While adjusting vehicle height, do not put anyone or anything on or in the vehicle because doing so will affect vehicle height.

  1. Disable the vehicle height control by pressing the height control mode select switch.

  1. Put the vehicle on a level surface.



    C181284E01
  1. Measure the vehicle height (C - D measurement) on the right side and left side.

    Standard vehicle height value:

  1. If the actual vehicle height (C - D measurement) differs from the standard vehicle height, adjust it by jacking up the frame, etc.

  1. Using the intelligent tester.

    1. Turn the ignition switch to ON or ACC.

    2. Using the intelligent tester measure the vehicle height values for the right side and the left side sensors.

      Difference between the intelligent tester value and vehicle height (C - D measurement):
      5 mm (0.196 in.) or less

      Difference between the right side and the left side:
      10 mm (0.393 in.) or less



    C179494E04
  1. Not using the intelligent tester.

    1. Disconnect the connector of the height control sensor.

    2. Connect three 1.5 V dry cell batteries in series.

    3. Connect the battery positive (+) and negative (-) ends to the terminals as shown in the illustration.

      Standard Voltage:
      Position
      Voltage
      High
      2.72 V
      Normal
      2.29 V
      Low
      1.86 V

      Difference between the right side and the left side:
      0.14 V or less



    C180797
  1. If the values measured in steps (e) and (f) are not as specified, adjust the vehicle height using the following procedure.

    1. Loosen the nut.

    2. Move the height control sensor link back and forth along the slotted hole of the bracket.

      HINT:
      Move the link toward the top of the vehicle to raise vehicle height. Move the link toward the bottom of the vehicle to lower vehicle height. Every 1 mm (0.0393 in.) change in the installation position of the link causes vehicle height to change by approximately 1 mm (0.0393 in.).

    3. Tighten the nut.

      Torque:
      5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

  1. Change the vehicle height (from the normal position to the high position, and from the high position to the normal position).

  1. Measure the vehicle height (C - D measurement) on the right side and left side.

  1. Check if the vehicle height (C - D measurement) is within the specified range.

    HINT:
    If the values are outside the standard, perform the procedures from (d) to (j) again.