SUSPENSION CONTROL SYSTEM > ADJUSTMENT |
| 1. ADJUST STANDARD VEHICLE HEIGHT |
Release the parking brake and stabilize the suspensions by pushing up and down on the corners of the vehicle.
Move the shift lever to N and settle the tires by moving the vehicle back and forth.
Start the engine.
On the height control switch, first press "HIGH" to raise the vehicle height, and then change the switch to "LOW" to lower it. Perform this operation one more time.
| 2. INSPECT TIRE |
Check the tires for wear and proper inflation pressure.
| Tire Size | Front kPa (kgf/cm2, psi) | Rear kPa (kgf/cm2, psi) | Spare kPa (kgf/cm2, psi) |
| P275/65R18 | 230 (2.3, 33) | 230 (2.3, 33) | 230 (2.3, 33) |
| P275/55R20 | 210 (2.1, 30) | 240 (2.4, 35) | 240 (2.4, 35) |
![]() |
Using a dial indicator, check the tire runout.
| 3. MEASURE VEHICLE HEIGHT |
![]() |
Press down on the vehicle several times to stabilize the suspension, and then measure the vehicle height.
| Vehicle Model | Rear Suspension Type | Tire Size | Front A - B | Rear C - D |
| USK60L-GKTSKV | Coil | P275/65R18 8JJ | 107.3 mm (4.22 in.) | 28.4 mm (1.12 in.) |
| P275/55R20 8JJ | 107.5 mm (4.23 in.) | 28.6 mm (1.13 in.) | ||
| USK60L-GKTLKV | Coil | P275/65R18 8JJ | 108.7 mm (4.28 in.) | 31.6 mm (1.24 in.) |
| P275/55R20 8JJ | 108.8 mm (4.28 in.) | 31.8 mm (1.25 in.) | ||
| USK60L-GKTZKV | Air + AVS | P275/55R20 8JJ | 108.6 mm (4.28 in.) | 39.5 mm (1.56 in.) |
| USK65L-GKTSKV | Coil | P275/65R18 8JJ | 102.9 mm (4.05 in.) | 24.4 mm (0.96 in.) |
| P275/55R20 8JJ | 102.9 mm (4.05 in.) | 24.4 mm (0.96 in.) | ||
| USK65L-GKTLKV | Coil | P275/65R18 8JJ | 104.0 mm (4.09 in.) | 26.8 mm (1.06 in.) |
| P275/55R20 8JJ | 104.0 mm (4.09 in.) | 26.8 mm (1.06 in.) | ||
| USK65L-GKTZKV | Air + AVS | P275/55R20 8JJ | 104.2 mm (4.10 in.) | 34.4 mm (1.35 in.) |
| 4. OPERATE HEIGHT CONTROL SWITCH AND CHECK VEHICLE HEIGHT CHANGE |
![]() |
Start the engine and change the height control switch from the NORMAL position to the HIGH and LOW positions.
Check the time until the height adjustment is completed and the amount of change in vehicle height.
| From operation of height control switch to start of compressor. | Approx. 2 sec. |
| From start of compressor to completion of height adjustment. (NORMAL→HIGH) | Approx. 25 sec. |
| From start of compressor to completion of height adjustment. (NORMAL→LOW) | Approx. 35 sec. |
| HIGH position | 30 mm (1.18 in.) |
| LOW position | 30 mm (1.18 in.) |
![]() |
While adjusting vehicle height in the HIGH position, start the engine and change the height control switch from the HIGH position to the NORM position.
While adjusting vehicle height in the LOW position, start the engine and change the height control switch from the LOW position to the NORM position.
Check the time until the height adjustment is completed and the amount of change in vehicle height.
| From operation of height control switch to open of exhaust valve. | Approx. 2 sec. |
| From open of exhaust valve to completion of height adjustment. (HIGH→NORMAL) | Approx. 35 sec. |
| From start of compressor to completion of height adjustment. (LOW→NORMAL) | Approx. 25 sec. |
| HIGH position | 30 mm (1.18 in.) |
| LOW position | 30 mm (1.18 in.) |
| 5. CHECK CONNECTIONS OF TUBES FOR AIR LEAK |
Set the height control switch in the HIGH position and raise the vehicle height.
Stop the engine.
Apply soapy water to the connections of the tubes and check if there is any air leakage.

| 6. ADJUST VEHICLE HEIGHT |
Disable the vehicle height control by pressing the height control mode select switch.
Put the vehicle on a level surface.
![]() |
Measure the vehicle height (C - D measurement) on the right side and left side.
If the actual vehicle height (C - D measurement) differs from the standard vehicle height, adjust it by jacking up the frame, etc.
Using the intelligent tester.
Turn the ignition switch to ON or ACC.
Using the intelligent tester measure the vehicle height values for the right side and the left side sensors.
![]() |
Not using the intelligent tester.
Disconnect the connector of the height control sensor.
Connect three 1.5 V dry cell batteries in series.
Connect the battery positive (+) and negative (-) ends to the terminals as shown in the illustration.
| Position | Voltage |
| High | 2.72 V |
| Normal | 2.29 V |
| Low | 1.86 V |
![]() |
If the values measured in steps (e) and (f) are not as specified, adjust the vehicle height using the following procedure.
Loosen the nut.
Move the height control sensor link back and forth along the slotted hole of the bracket.
Tighten the nut.
Change the vehicle height (from the normal position to the high position, and from the high position to the normal position).
Measure the vehicle height (C - D measurement) on the right side and left side.
Check if the vehicle height (C - D measurement) is within the specified range.