Home › Suspension › ALIGNMENT / HANDLING DIAGNOSIS › FRONT WHEEL ALIGNMENT

FRONT WHEEL ALIGNMENT > ADJUSTMENT

for Preparation Click here


NOTICE:
For vehicles equipped with VSC, if the wheel alignment has been adjusted, or if suspension or underbody components have been removed/installed or replaced, be sure to perform the following initialization procedure in order for the system to function normally:
  1. Disconnect the cable from the negative (-) battery terminal for more than 2 seconds.
  2. Reconnect the cable to the negative (-) battery terminal.
  3. Perform zero point calibration of the yaw rate and deceleration sensor, and test mode inspection (Click here).



1. INSPECT TIRE
  1. Check the tires for wear and proper inflation pressure.

    Standard Cold Tire Inflation Pressure:
    Tire Size
    Front
    kPa (kgf/cm2, psi)
    Rear
    kPa (kgf/cm2, psi)
    Spare
    kPa (kgf/cm2, psi)
    P275/65R18
    230 (2.3, 33)
    230 (2.3, 33)
    230 (2.3, 33)
    P275/55R20
    210 (2.1, 30)
    240 (2.4, 35)
    240 (2.4, 35)



    R003031
  1. Using a dial indicator, check the tire runout.

    Tire runout:
    3.0 mm (0.118 in.) or less



2. MEASURE VEHICLE HEIGHT

NOTICE:
Before inspecting the wheel alignment, adjust the vehicle height to the specification.



    C180789E01
  1. Press down on the vehicle several times to stabilize the suspension, and then measure the vehicle height.

    Standard Vehicle Height (Unloaded Vehicle):

    Vehicle Model
    Rear Suspension Type
    Tire Size
    Front A - B
    Rear C - D
    USK60L-GKTSKV
    Coil
    P275/65R18 8JJ
    107.3 mm (4.22 in.)
    28.4 mm (1.12 in.)
    P275/55R20 8JJ
    107.5 mm (4.23 in.)
    28.6 mm (1.13 in.)
    Air
    P275/65R18 8JJ
    106.1 mm (4.18 in.)
    39.1 mm (1.54 in.)
    P275/55R20 8JJ
    106.2 mm (4.18 in.)
    39.3 mm (1.55 in.)
    USK60L-GKTLKV
    Coil
    P275/65R18 8JJ
    108.7 mm (4.28 in.)
    31.6 mm (1.24 in.)
    P275/55R20 8JJ
    108.8 mm (4.28 in.)
    31.8 mm (1.25 in.)
    Air
    P275/65R18 8JJ
    107.7 mm (4.24 in.)
    39.2 mm (1.54 in.)
    P275/55R20 8JJ
    107.9 mm (4.25 in.)
    39.5 mm (1.56 in.)
    USK60L-GKTZKV
    Air + AVS
    P275/55R20 8JJ
    108.6 mm (4.28 in.)
    39.5 mm (1.56 in.)
    USK65L-GKTSKV
    Coil
    P275/65R18 8JJ
    102.9 mm (4.05 in.)
    24.4 mm (0.96 in.)
    P275/55R20 8JJ
    102.9 mm (4.05 in.)
    24.4 mm (0.96 in.)
    Air
    P275/65R18 8JJ
    101.7 mm (4.00 in.)
    34.1 mm (1.34 in.)
    P275/55R20 8JJ
    101.8 mm (4.01 in.)
    34.1 mm (1.34 in.)
    USK65L-GKTLKV
    Coil
    P275/65R18 8JJ
    104.0 mm (4.09 in.)
    26.8 mm (1.06 in.)
    P275/55R20 8JJ
    104.0 mm (4.09 in.)
    26.8 mm (1.06 in.)
    Air
    P275/65R18 8JJ
    103.1 mm (4.06 in.)
    34.2 mm (1.35 in.)
    P275/55R20 8JJ
    103.1 mm (4.06 in.)
    34.3 mm (1.35 in.)
    USK65L-GKTZKV
    Air + AVS
    P275/55R20 8JJ
    104.2 mm (4.10 in.)
    34.4 mm (1.35 in.)

    1. Measuring points

    A:
    Ground clearance of the front drive shaft center

    B:
    Ground clearance of the front adjusting cam bolt center

    C:
    Ground clearance of the rear drive shaft center

    D:
    Ground clearance of the rear lower arm No. 1 adjusting cam bolt center

    If the vehicle height is not as specified, adjust the height by pressing down on the vehicle several times to stabilize the suspension.



3. INSPECT WHEEL ANGLE
  1. Turn the steering wheel to the left and right to the full lock positions and measure the turning angle.

    Standard Wheel Angle (Unloaded Vehicle):

    Vehicle Model
    Rear Suspension Type
    Tire Size
    Inside Wheel Angle
    Outside Wheel Angle (Reference)
    USK60L-GKTSKV
    Coil
    P275/65R18 8JJ
    -41°01' (-41.01°)
    36°23' (36.39°)
    P275/55R20 8JJ
    -41°01' (-41.01°)
    36°23' (36.39°)
    Air
    P275/65R18 8JJ
    -41°01' (-41.01°)
    36°24' (36.40°)
    P275/55R20 8JJ
    -41°01' (-41.01°)
    36°24' (36.40°)
    USK60L-GKTLKV
    Coil
    P275/65R18 8JJ
    -40°59' (-40.98°)
    36°21' (36.35°)
    P275/55R20 8JJ
    -40°59' (-40.98°)
    36°21' (36.35°)
    Air
    P275/65R18 8JJ
    -40°59' (-40.99°)
    36°22' (36.36°)
    P275/55R20 8JJ
    -40°59' (-40.99°)
    36°22' (36.36°)
    USK60L-GKTZKV
    Air + AVS
    P275/55R20 8JJ
    -40°59' (-40.98°)
    36°20' (36.33°)
    USK65L-GKTSKV
    Coil
    P275/65R18 8JJ
    -41°16' (-41.27°)
    36°23' (36.38°)
    P275/55R20 8JJ
    -41°16' (-41.27°)
    36°23' (36.38°)
    Air
    P275/65R18 8JJ
    -41°16' (-41.27°)
    36°23' (36.39°)
    P275/55R20 8JJ
    -41°16' (-41.27°)
    36°23' (36.39°)
    USK65L-GKTLKV
    Coil
    P275/65R18 8JJ
    -41°15' (-41.25°)
    36°20' (36.34°)
    P275/55R20 8JJ
    -41°15' (-41.25°)
    36°20' (36.34°)
    Air
    P275/65R18 8JJ
    -41°15' (-41.25°)
    36°21' (36.35°)
    P275/55R20 8JJ
    -41°15' (-41.25°)
    36°21' (36.35°)
    USK65L-GKTZKV
    Air + AVS
    P275/55R20 8JJ
    -41°14' (-41.24°)
    36°19' (36.32°)



4. INSPECT CAMBER, CASTER AND STEERING AXIS INCLINATION


Z003382E06
  1. Install a camber-caster-kingpin gauge or place the front wheels on the center of a wheel alignment tester.

  1. Inspect the camber, caster and steering axis inclination.

    Standard Camber, Caster, Steering Axis Inclination (Unloaded Vehicle):

    Vehicle Model
    Rear Suspension Type
    Tire Size
    Camber Inclination
    Caster Inclination
    Steering Axis Inclination
    USK60L-GKTSKV
    Coil
    P275/65R18 8JJ
    -0°09' +/-45'
    (-0.15° +/-0.75°)
    3°43' +/-45'
    (3.71° +/-0.75°)
    13°10' +/-45'
    (13.17° +/-0.75°)
    P275/55R20 8JJ
    -0°09' +/-45'
    (-0.15° +/-0.75°)
    3°43' +/-45'
    (3.71° +/-0.75°)
    13°10' +/-45'
    (13.17° +/-0.75°)
    Air
    P275/65R18 8JJ
    -0°08' +/-45'
    (-0.14° +/-0.75°)
    3°56' +/-45'
    (3.93° +/-0.75°)
    13°10' +/-45'
    (13.16° +/-0.75°)
    P275/55R20 8JJ
    -0°08' +/-45'
    (-0.14° +/-0.75°)
    3°55' +/-45'
    (3.92° +/-0.75°)
    13°10' +/-45'
    (13.16° +/-0.75°)
    USK60L-GKTLKV
    Coil
    P275/65R18 8JJ
    -0°11' +/-45'
    (-0.18° +/-0.75°)
    3°48' +/-45'
    (3.80° +/-0.75°)
    13°12' +/-45'
    (13.20° +/-0.75°)
    P275/55R20 8JJ
    -0°11' +/-45'
    (-0.18° +/-0.75°)
    3°47' +/-45'
    (3.79° +/-0.75°)
    13°12' +/-45'
    (13.20° +/-0.75°)
    Air
    P275/65R18 8JJ
    -0°10' +/-45'
    (-0.17° +/-0.75°)
    3°57' +/-45'
    (3.95° +/-0.75°)
    13°11' +/-45'
    (13.19° +/-0.75°)
    P275/55R20 8JJ
    -0°10' +/-45'
    (-0.17° +/-0.75°)
    3°56' +/-45'
    (3.94° +/-0.75°)
    13°11' +/-45'
    (13.19° +/-0.75°)
    USK60L-GKTZKV
    Air + AVS
    P275/55R20 8JJ
    -0°11' +/-45'
    (-0.19° +/-0.75°)
    3°57' +/-45'
    (3.95° +/-0.75°)
    13°13' +/-45'
    (13.21° +/-0.75°)
    USK65L-GKTSKV
    Coil
    P275/65R18 8JJ
    -0°02' +/-45'
    (-0.03° +/-0.75°)
    3°37' +/-45'
    (3.62° +/-0.75°)
    13°04' +/-45'
    (13.07° +/-0.75°)
    P275/55R20 8JJ
    -0°02' +/-45'
    (-0.03° +/-0.75°)
    3°35' +/-45'
    (3.58° +/-0.75°)
    13°04' +/-45'
    (13.07° +/-0.75°)
    Air
    P275/65R18 8JJ
    -0°01' +/-45'
    (-0.02° +/-0.75°)
    3°49' +/-45'
    (3.82° +/-0.75°)
    13°04' +/-45'
    (13.06° +/-0.75°)
    P275/55R20 8JJ
    -0°01' +/-45'
    (-0.02° +/-0.75°)
    3°46' +/-45'
    (3.77° +/-0.75°)
    13°04' +/-45'
    (13.06° +/-0.75°)
    USK65L-GKTLKV
    Coil
    P275/65R18 8JJ
    -0°04' +/-45'
    (-0.06° +/-0.75°)
    3°41' +/-45'
    (3.68° +/-0.75°)
    13°06' +/-45'
    (13.10° +/-0.75°)
    P275/55R20 8JJ
    -0°04' +/-45'
    (-0.06° +/-0.75°)
    3°38' +/-45'
    (3.63° +/-0.75°)
    13°06' +/-45'
    (13.10° +/-0.75°)
    Air
    P275/65R18 8JJ
    -0°03' +/-45'
    (-0.05° +/-0.75°)
    3°50' +/-45'
    (3.83° +/-0.75°)
    13°05' +/-45'
    (13.09° +/-0.75°)
    P275/55R20 8JJ
    -0°03' +/-45'
    (-0.05° +/-0.75°)
    3°47' +/-45'
    (3.78° +/-0.75°)
    13°05' +/-45'
    (13.09° +/-0.75°)
    USK65L-GKTZKV
    Air + AVS
    P275/55R20 8JJ
    -0°04' +/-45'
    (-0.07° +/-0.75°)
    3°47' +/-45'
    (3.79° +/-0.75°)
    13°07' +/-45'
    (13.11° +/-0.75°)

    NOTICE:
    The maximum tolerance of right and left difference for the camber and caster is 30' or less.



5. ADJUST CAMBER AND CASTER

HINT:
After the camber has been adjusted, inspect the toe-in.

  1. Loosen the toe adjusting cam bolt and camber adjusting cam nut.



  1. Turn the toe adjusting cam and camber adjusting cam in both directions, and adjust the camber and caster to the center value.

    HINT:
    The camber and caster should be as close as possible to the center value.

    C183664E01



    C183666E02
  1. Read the adjustment chart (example).

    1. Find the wheel alignment standard value applicable for the particular model.

    2. Mark the standard value on the adjustment chart.

      Standard Value (Reference):
      Camber
      Caster
      0°03' (0.05°)
      4°07' (4.12°)

    3. Mark the alignment value measured when the vehicle is unloaded on the adjustment chart.

      Measured Value (Reference):
      Camber
      Caster
      0°20' (0.33°)
      4°00' (4.00°)



    4. As shown in the chart, read the distance from the marked point to 0, and adjust the front and/ or rear adjusting cams accordingly.

      Amount to Turn Adjusting Cams (by Gradation):
      Front Adjusting Cam
      Rear Adjusting Cam
      +1.5
      +2.0



      C183665E02



6. INSPECT TOE-IN


A166181E01
  1. Bounce the vehicle up and down at the corners to stabilize the suspension, and then inspect the toe-in.

    Standard Toe-in (Unloaded Vehicle):

    Vehicle Model
    Rear Suspension Type
    Tire Size
    B - A
    USK60L-GKTSKV
    Coil
    P275/65R18 8JJ
    2.37 mm (0.0933 in.)
    P275/55R20 8JJ
    2.37 mm (0.0933 in.)
    Air
    P275/65R18 8JJ
    2.49 mm (0.0980 in.)
    P275/55R20 8JJ
    2.49 mm (0.0980 in.)
    USK60L-GKTLKV
    Coil
    P275/65R18 8JJ
    1.97 mm (0.0776 in.)
    P275/55R20 8JJ
    1.97 mm (0.0776 in.)
    Air
    P275/65R18 8JJ
    2.06 mm (0.0811 in.)
    P275/55R20 8JJ
    2.06 mm (0.0811 in.)
    USK60L-GKTZKV
    Air + AVS
    P275/55R20 8JJ
    1.88 mm (0.0740 in.)
    USK65L-GKTSKV
    Coil
    P275/65R18 8JJ
    2.09 mm (0.0823 in.)
    P275/55R20 8JJ
    2.09 mm (0.0823 in.)
    Air
    P275/65R18 8JJ
    2.19 mm (0.0862 in.)
    P275/55R20 8JJ
    2.19 mm (0.0862 in.)
    USK65L-GKTLKV
    Coil
    P275/65R18 8JJ
    1.78 mm (0.0701 in.)
    P275/55R20 8JJ
    1.78 mm (0.0701 in.)
    Air
    P275/65R18 8JJ
    1.86 mm (0.0732 in.)
    P275/55R20 8JJ
    1.86 mm (0.0732 in.)
    USK65L-GKTZKV
    Air + AVS
    P275/55R20 8JJ
    1.60 mm (0.0630 in.)

    1. If the toe-in is not as specified, adjust it at the rack ends.



7. ADJUST TOE-IN
  1. Release the rack boot set clips.

  1. Loosen the tie rod end lock nuts.

  1. Turn the right and left rack ends by an equal amount to adjust the toe-in to the center value.



    C159783E01
  1. Check that the lengths of the right and left rack ends are approximately the same.

    Standard difference:
    0 +/-1 mm (0 +/-0.0394 in.)

  1. Tighten the tie rod end lock nuts.

    Torque:
    82 N*m{ 836 kgf*cm , 61 ft.*lbf }

  1. Attach the clips to the boots.

    HINT:
    Make sure that the boots are not twisted.



8. PLACE FRONT WHEELS FACING STRAIGHT AHEAD


9. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
Disconnect the cable from the negative (-) battery terminal for more than 2 seconds.



10. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



11. PERFORM YAW RATE SENSOR ZERO POINT CALIBRATION
(Click here)


12. CHECK STEERING ANGLE SENSOR ZERO POINT CALIBRATION
(Click here )