DTC B1660/43 Passenger Airbag ON/OFF Indicator Circuit Malfunction |
| DTC Code | Detection Condition | Trouble Area |
| B1660/43 | When one of following conditions is met:
|
|

| 1.CHECK PASSENGER AIRBAG ON/OFF INDICATOR CONDITION |

Turn the ignition switch to ON.
Check the passenger airbag ON/OFF indicator operation.
| ON/OFF Indicator Illumination | Proceed to |
| Always on | A |
| Off | B |
|
| ||||
| A | |
| 2.CHECK CONNECTION OF CONNECTORS |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor and the integration control and panel.
|
| ||||
| OK | |
| 3.CHECK CONNECTORS |
Disconnect the connectors from the center airbag sensor and the telltale light.
Check that the connectors (on the center airbag sensor side and integration control and panel side) are not damaged (Click here).
|
| ||||
| OK | |
| 4.CHECK PASSENGER AIRBAG ON/OFF INDICATOR |
![]() |
Connect the connector to the integration control and panel.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Check the passenger airbag ON/OFF indicator operation.
|
| ||||
| OK | |
| 5.CHECK CENTER AIRBAG SENSOR |
![]() |
Connect the connector to the center airbag sensor.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| OK | ||
| ||
| 6.CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - INTEGRATION CONTROL AND PANEL) |

Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect the connector from the integration control and panel.
Using a service wire, connect terminals 23 (PAON) and 17 (P-AB) of connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| H45-5 (PAON) - H45-13 (P-AB) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| H45-5 (PAON) - H45-13 (P-AB) | Always | 1 MΩ or higher |
| H45-5 (PAON) - Body ground | Always | 1 MΩ or higher |
| H45-13 (P-AB) - Body ground | Always | 1 MΩ or higher |
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| H45-5 (PAON) - Body ground | Ignition switch ON | Below 1 V |
| H45-13 (P-AB) - Body ground | Ignition switch ON | Below 1 V |
|
| ||||
| OK | ||
| ||
| 7.CHECK CONNECTION OF CONNECTORS |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor and the integration control and panel.
|
| ||||
| OK | |
| 8.CHECK CONNECTORS |
Disconnect the connectors from the center airbag sensor and the telltale light.
Check that the connectors (on the center airbag sensor side and integration control and panel side) are not damaged (Click here).
|
| ||||
| OK | |
| 9.CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - INTEGRATION CONTROL AND PANEL) |

Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect the connector from the integration control and panel.
Using a service wire, connect terminals 23 (PAON) and 17 (P-AB) of connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| H45-5 (PAON) - H45-13 (P-AB) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| H45-5 (PAON) - H45-13 (P-AB) | Always | 1 MΩ or higher |
| H45-5 (PAON) - Body ground | Always | 1 MΩ or higher |
| H45-13 (P-AB) - Body ground | Always | 1 MΩ or higher |
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| H45-5 (PAON) - Body ground | Ignition switch ON | Below 1 V |
| H45-13 (P-AB) - Body ground | Ignition switch ON | Below 1 V |
|
| ||||
| OK | |
| 10.CHECK PASSENGER AIRBAG ON/OFF INDICATOR (SOURCE VOLTAGE) |
![]() |
Connect the connectors to the center airbag sensor.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| H45-16 (IG+) - Body ground | Ignition switch ON | 11 to 14 V |
|
| ||||
| OK | |
| 11.CHECK PASSENGER AIRBAG ON/OFF INDICATOR |
![]() |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Connect the connector to the integration control and panel.
Disconnect the connectors from the center airbag sensor.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Check the indicator according to the value(s) in the table below.
| Connection | Switch Condition | Passenger airbag ON/OFF indicator |
| H56-23 (PAON) - Body ground | Ignition switch ON | "ON" comes on |
| H56-17 (P-AB) - Body ground | Ignition switch ON | "OFF" comes on |
|
| ||||
| OK | |
| 12.CHECK CENTER AIRBAG SENSOR |
![]() |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Connect the connectors to the center airbag sensor.
Connect the cable to the negative (-) battery terminal and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| OK | ||
| ||