Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM

DTC    B1660/43    Passenger Airbag ON/OFF Indicator Circuit Malfunction

for Preparation Click here


DESCRIPTION

The passenger airbag ON/OFF indicator circuit consists of the center airbag sensor and the passenger airbag ON/OFF indicator.
The passenger airbag ON/OFF indicator indicates the operation condition of the front passenger airbag, front seat side airbag RH and front seat outer belt RH.
DTC B1660/43 is stored when a malfunction is detected in the passenger airbag ON/OFF indicator circuit.

DTC Code
Detection Condition
Trouble Area
B1660/43
When one of following conditions is met:
  1. The center airbag sensor receives an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the passenger airbag ON/OFF indicator circuit for 2 seconds.
  2. Passenger airbag ON/OFF indicator malfunction
  3. Center airbag sensor malfunction
  1. Instrument panel wire
  2. Integration control and panel (Passenger airbag ON/OFF indicator)
  3. Center airbag sensor assembly

WIRING DIAGRAM


C181203E01


INSPECTION PROCEDURE

1.CHECK PASSENGER AIRBAG ON/OFF INDICATOR CONDITION

C123768E60

  1. Turn the ignition switch to ON.

  1. Check the passenger airbag ON/OFF indicator operation.

    HINT:
    Refer to the normal condition of the passenger airbag ON/OFF indicator (Click here).

    Result 
    ON/OFF Indicator Illumination
    Proceed to
    Always on
    A
    Off
    B



B
Go to step 7
A


2.CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor and the integration control and panel.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


3.CHECK CONNECTORS
  1. Disconnect the connectors from the center airbag sensor and the telltale light.

  1. Check that the connectors (on the center airbag sensor side and integration control and panel side) are not damaged (Click here).

    OK:
    The connectors are not deformed or damaged.



NG
REPLACE INSTRUMENT PANEL WIRE
OK


4.CHECK PASSENGER AIRBAG ON/OFF INDICATOR
C157844
  1. Connect the connector to the integration control and panel.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON.

  1. Check the passenger airbag ON/OFF indicator operation.

    OK:
    The passenger airbag ON/OFF indicator does not come on.



NG
Go to step 6
OK


5.CHECK CENTER AIRBAG SENSOR
C146229E26
  1. Connect the connector to the center airbag sensor.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1660/43 is not output.

    HINT:
    Codes other than DTC B1660/43 may be output at this time, but they are not related to this check.

    Result 
    Result
    Proceed to
    OK
    A
    NG (w/ Cool Box)
    B
    NG (w/o Cool Box)
    C



B
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)

C
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)  

6.CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - INTEGRATION CONTROL AND PANEL)

C159195E02

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect the connector from the integration control and panel.

  1. Using a service wire, connect terminals 23 (PAON) and 17 (P-AB) of connector B.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H45-5 (PAON) - H45-13 (P-AB)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H45-5 (PAON) - H45-13 (P-AB)
    Always
    1 MΩ or higher
    H45-5 (PAON) - Body ground
    Always
    1 MΩ or higher
    H45-13 (P-AB) - Body ground
    Always
    1 MΩ or higher

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    H45-5 (PAON) - Body ground
    Ignition switch ON
    Below 1 V
    H45-13 (P-AB) - Body ground
    Ignition switch ON
    Below 1 V



NG
REPLACE INSTRUMENT PANEL WIRE
OK

REPLACE INTEGRATION CONTROL AND PANEL (Click here)  

7.CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor and the integration control and panel.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


8.CHECK CONNECTORS
  1. Disconnect the connectors from the center airbag sensor and the telltale light.

  1. Check that the connectors (on the center airbag sensor side and integration control and panel side) are not damaged (Click here).

    OK:
    The connectors are not deformed or damaged.



NG
REPLACE INSTRUMENT PANEL WIRE
OK


9.CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - INTEGRATION CONTROL AND PANEL)

C159195E02

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect the connector from the integration control and panel.

  1. Using a service wire, connect terminals 23 (PAON) and 17 (P-AB) of connector B.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H45-5 (PAON) - H45-13 (P-AB)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H45-5 (PAON) - H45-13 (P-AB)
    Always
    1 MΩ or higher
    H45-5 (PAON) - Body ground
    Always
    1 MΩ or higher
    H45-13 (P-AB) - Body ground
    Always
    1 MΩ or higher

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    H45-5 (PAON) - Body ground
    Ignition switch ON
    Below 1 V
    H45-13 (P-AB) - Body ground
    Ignition switch ON
    Below 1 V



NG
REPLACE INSTRUMENT PANEL WIRE
OK


10.CHECK PASSENGER AIRBAG ON/OFF INDICATOR (SOURCE VOLTAGE)
C159496E02
  1. Connect the connectors to the center airbag sensor.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    H45-16 (IG+) - Body ground
    Ignition switch ON
    11 to 14 V



NG
REPLACE HARNESS AND CONNECTOR (INTEGRATION CONTROL AND PANEL - BATTERY)
OK


11.CHECK PASSENGER AIRBAG ON/OFF INDICATOR
C159497E04
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Connect the connector to the integration control and panel.

  1. Disconnect the connectors from the center airbag sensor.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON.

  1. Check the indicator according to the value(s) in the table below.

    OK:
    Connection
    Switch Condition
    Passenger airbag ON/OFF indicator
    H56-23 (PAON) - Body ground
    Ignition switch ON
    "ON" comes on
    H56-17 (P-AB) - Body ground
    Ignition switch ON
    "OFF" comes on



NG
REPLACE INTEGRATION CONTROL AND PANEL (Click here)
OK


12.CHECK CENTER AIRBAG SENSOR
C146229E11
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Connect the connectors to the center airbag sensor.

  1. Connect the cable to the negative (-) battery terminal and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1660/43 is not output.

    HINT:
    Codes other than DTC B1660/43 may be output at this time, but they are not related to this check.

    Result 
    Result
    Proceed to
    OK
    A
    NG (w/ Cool Box)
    B
    NG (w/o Cool Box)
    C



B
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)

C
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)