Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM

NAVIGATION SYSTEM > Speaker Circuit

for Preparation Click here


DESCRIPTION

The navigation receiver assembly sends sound signals to the speakers.

WIRING DIAGRAM


E283170E02


E283171E02


INSPECTION PROCEDURE

1.CHECK HARNESS AND CONNECTOR (FRONT SPEAKER RH CIRCUIT)
  1. Disconnect the I41 navigation receiver assembly connectors.

  1. Disconnect the L1 front No. 3 speaker assembly RH connector.

  1. Disconnect the I11 front No. 2 speaker assembly RH connector.

  1. Disconnect the L8 front No. 1 speaker assembly RH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L1-3 - I11-1 (+)
    Always
    Below 1 Ω
    L1-1 - I11-2 (-)
    Always
    Below 1 Ω
    I11-3 (TWR+) - I41-1 (FR+)
    Always
    Below 1 Ω
    I11-4 (TWR-) - I41-5 (FR-)
    Always
    Below 1 Ω
    L8-1 - I41-1 (FR+)
    Always
    Below 1 Ω
    L8-2 - I41-5 (FR-)
    Always
    Below 1 Ω
    L1-3 - Body ground
    Always
    10 kΩ or higher
    L1-1 - Body ground
    Always
    10 kΩ or higher
    I11-3 (TWR+) - Body ground
    Always
    10 kΩ or higher
    I11-4 (TWR-) - Body ground
    Always
    10 kΩ or higher
    L8-1 - Body ground
    Always
    10 kΩ or higher
    L8-2 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.CHECK HARNESS AND CONNECTOR (FRONT SPEAKER LH CIRCUIT)
  1. Disconnect the I41 navigation receiver assembly connectors.

  1. Disconnect the M1 front No. 3 speaker assembly LH connector.

  1. Disconnect the I13 front No. 2 speaker assembly LH connector.

  1. Disconnect the M10 front No. 1 speaker assembly LH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    M1-3 - I13-1 (+)
    Always
    Below 1 Ω
    M1-1 - I13-2 (-)
    Always
    Below 1 Ω
    I13-3 (TWL+) - I41-2 (FL+)
    Always
    Below 1 Ω
    I13-4 (TWL-) - I41-6 (FL-)
    Always
    Below 1 Ω
    M10-1 - I41-2 (FL+)
    Always
    Below 1 Ω
    M10-2 - I41-6 (FL-)
    Always
    Below 1 Ω
    M1-3 - Body ground
    Always
    10 kΩ or higher
    M1-1 - Body ground
    Always
    10 kΩ or higher
    I13-3 (TWL+) - Body ground
    Always
    10 kΩ or higher
    I13-4 (TWL-) - Body ground
    Always
    10 kΩ or higher
    M10-1 - Body ground
    Always
    10 kΩ or higher
    M10-2 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK HARNESS AND CONNECTOR (REAR SPEAKER RH CIRCUIT)
  1. Disconnect the I42 navigation receiver assembly connectors.

  1. Disconnect the N2 rear No. 2 speaker assembly RH connector.

  1. Disconnect the O37 quarter side speaker assembly RH connector.

  1. Disconnect the N1 rear No. 1 speaker assembly RH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    N2-3 - O37-3 (+)
    Always
    Below 1 Ω
    N2-1 - O37-4 (-)
    Always
    Below 1 Ω
    O37-1 (+) - I42-1 (RR+)
    Always
    Below 1 Ω
    O37-2 (-) - I42-3 (RR-)
    Always
    Below 1 Ω
    N1-1 - I42-1 (RR+)
    Always
    Below 1 Ω
    N1-2 - I42-3 (RR-)
    Always
    Below 1 Ω
    N2-3 - Body ground
    Always
    10 kΩ or higher
    N2-1 - Body ground
    Always
    10 kΩ or higher
    O37-1 (+) - Body ground
    Always
    10 kΩ or higher
    O37-2 (-) - Body ground
    Always
    10 kΩ or higher
    N1-1 - Body ground
    Always
    10 kΩ or higher
    N1-2 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (REAR SPEAKER LH CIRCUIT)
  1. Disconnect the I42 navigation receiver assembly connectors.

  1. Disconnect the N8 rear No. 2 speaker assembly LH connector.

  1. Disconnect the O31 quarter side speaker assembly LH connector.

  1. Disconnect the N7 rear No. 1 speaker assembly LH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    N8-3 - O31-3 (+)
    Always
    Below 1 Ω
    N8-1 - O31-4 (-)
    Always
    Below 1 Ω
    O31-1 (+) - I42-2 (RL+)
    Always
    Below 1 Ω
    O31-2 (-) - I42-6 (RL-)
    Always
    Below 1 Ω
    N7-1 - I42-2 (RL+)
    Always
    Below 1 Ω
    N7-2 - I42-6 (RL-)
    Always
    Below 1 Ω
    N8-3 - Body ground
    Always
    10 kΩ or higher
    N8-1 - Body ground
    Always
    10 kΩ or higher
    O31-1 (+) - Body ground
    Always
    10 kΩ or higher
    O31-2 (-) - Body ground
    Always
    10 kΩ or higher
    N7-1 - Body ground
    Always
    10 kΩ or higher
    N7-2 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY
  1. Remove the front No. 1 speaker assembly (Click here).

  1. Inspect the front No. 1 speaker assembly (Click here).



NG
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY (Click here)
OK


6.CHECK FRONT NO. 2 SPEAKER ASSEMBLY
  1. Replace the front No. 2 speaker assembly with a known good one (Click here).

  1. Check that the malfunction disappears.

    NOTICE:
    1. Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.
    2. Perform the above inspection on both LH and RH sides.

    OK:
    Malfunction disappears.



NG
Go to step 7
OK

END (FRONT NO. 2 SPEAKER ASSEMBLY IS DEFECTIVE) 

7.CHECK FRONT NO. 3 SPEAKER ASSEMBLY
  1. Replace the front No. 3 speaker assembly with a known good one (Click here).

  1. Check that the malfunction disappears.

    NOTICE:
    1. Connect all the connectors to the front No. 3 speaker assemblies that were disconnected.
    2. Perform the above inspection on both LH and RH sides.

    OK:
    Malfunction disappears.



NG
Go to step 8
OK

END (FRONT NO. 3 SPEAKER ASSEMBLY IS DEFECTIVE) 

8.CHECK REAR NO. 1 SPEAKER ASSEMBLY
  1. Remove the rear No. 1 speaker assembly (Click here).

  1. Inspect the rear No. 1 speaker assembly (Click here).



NG
REPLACE REAR NO. 1 SPEAKER ASSEMBLY (Click here)
OK


9.CHECK REAR NO. 2 SPEAKER ASSEMBLY
  1. Replace the rear No. 2 speaker assembly with a known good one (Click here).

  1. Check that the malfunction disappears.

    NOTICE:
    1. Connect all the connectors to the rear No. 2 speaker assemblies that were disconnected.
    2. Perform the above inspection on both LH and RH sides.

    OK:
    Malfunction disappears.



NG
Go to step 10
OK

END (FRONT NO. 2 SPEAKER ASSEMBLY IS DEFECTIVE) 

10.CHECK QUARTER SIDE SPEAKER ASSEMBLY
  1. Replace the quarter side speaker assembly with a known good one (Click here).

  1. Check that the malfunction disappears.

    NOTICE:
    1. Connect all the connectors to the quarter side speaker assemblies that were disconnected.
    2. Perform the above inspection on both LH and RH sides.

    OK:
    Malfunction disappears.



NG
REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)
OK

END (QUARTER SIDE SPEAKER ASSEMBLY IS DEFECTIVE)