Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › REAR VIEW MONITOR SYSTEM (w/ Navigation System)

REAR VIEW MONITOR SYSTEM (w/ Navigation System) > Display Signal Circuit between Navigation Receiver Assembly and Television Camera Assembly

for Preparation Click here


DESCRIPTION

This is the display signal circuit between the navigation receiver assembly and the rear television camera assembly.

WIRING DIAGRAM


E182334E15


INSPECTION PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY)
  1. Disconnect the I52 navigation receiver assembly connector.

  1. Disconnect the V23 rear television camera assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I52-8 (V+) - V23-3 (CV+)
    Always
    Below 1 Ω
    I52-16 (V-) - V23-2 (CV-)
    Always
    Below 1 Ω
    I52-15 (CGND) - V23-5 (CGND)
    Always
    Below 1 Ω
    I52-7 (CA+) - V23-6 (CB+)
    Always
    Below 1 Ω
    I52-7 (V+) - Body ground
    Always
    10 kΩ or higher
    I52-16 (V-) - Body ground
    Always
    10 kΩ or higher
    I52-15 (CGND) - Body ground
    Always
    10 kΩ or higher
    I52-7 (CA+) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.CHECK NAVIGATION RECEIVER ASSEMBLY
E259221E02
  1. Disconnect the I52 navigation receiver assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection
Condition
Specified Condition
I52-15 (CGND) - Body ground
Always
Below 1 Ω
I52-16 (V-) - Body ground
Always
Below 1 Ω

Text in Illustration 
*a
Component without harness connected
(Navigation Receiver Assembly)


NG
REPLACE NAVIGATION RECEIVER ASSEMBLY
OK


3.CHECK NAVIGATION RECEIVER ASSEMBLY
E258515E02
  1. Disconnect the V23 rear television camera assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    V23-6 (CB+) - V23-5 (CGND)
    Ignition switch ON, shift lever in R
    5.5 to 7.05 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Rear Television Camera Assembly)



NG
REPLACE NAVIGATION RECEIVER ASSEMBLY
OK


4.CHECK REAR TELEVISION CAMERA ASSEMBLY


  1. Using an oscilloscope, check the waveform.


    E259222E02


    Text in Illustration 
    *a
    Component with harness connected
    (Navigation Receiver Assembly)
    *b
    Waveform 1
    *c
    Waveform 2
    *d
    Synchronized Signal
    *e
    Video Waveform
    -
    -

    HINT:
    A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the navigation receiver assembly with the connector connected.

    Measurement Condition 
    Item
    Content
    Terminal No. (Symbol)
    I52-8 (V+) - I52-16 (V-)
    Tool Setting
    0.2 V/DIV., 50 μs/DIV.
    Condition
    1. Waveform 1: Ignition switch ON, shift lever in R
    2. Waveform 2: Ignition switch ON, shift lever in R, screen blacked out by covering camera lens

    OK:
    Waveform is as shown in the illustration.

    HINT:
    The video waveform changes according to the image sent by the rear television camera assembly.



NG
REPLACE REAR TELEVISION CAMERA ASSEMBLY (Click here)
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)