DTC B15C3 Speaker Output Short |
| DTC Code | DTC Detection Condition | Trouble Area |
| B15C3 | A short is detected in the speaker output circuit. |
|


| 1.CHECK FOR DTC |
Clear the DTCs (Click here).
Check for DTCs (Click here).
|
| ||||
| OK | ||
| ||
| 2.CHECK HARNESS AND CONNECTOR (FRONT SPEAKER RH CIRCUIT) |
Disconnect the I41 navigation receiver assembly connectors.
Disconnect the L1 front No. 3 speaker assembly RH connector.
Disconnect the I11 front No. 2 speaker assembly RH connector.
Disconnect the L8 front No. 1 speaker assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| L1-3 - I11-1 (+) | Always | Below 1 Ω |
| L1-1 - I11-2 (-) | Always | Below 1 Ω |
| I11-3 (TWR+) - I41-1 (FR+) | Always | Below 1 Ω |
| I11-4 (TWR-) - I41-5 (FR-) | Always | Below 1 Ω |
| L8-1 - I41-1 (FR+) | Always | Below 1 Ω |
| L8-2 - I41-5 (FR-) | Always | Below 1 Ω |
| L1-3 - Body ground | Always | 10 kΩ or higher |
| L1-1 - Body ground | Always | 10 kΩ or higher |
| I11-3 (TWR+) - Body ground | Always | 10 kΩ or higher |
| I11-4 (TWR-) - Body ground | Always | 10 kΩ or higher |
| L8-1 - Body ground | Always | 10 kΩ or higher |
| L8-2 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (FRONT SPEAKER LH CIRCUIT) |
Disconnect the I41 navigation receiver assembly connectors.
Disconnect the M1 front No. 3 speaker assembly LH connector.
Disconnect the I13 front No. 2 speaker assembly LH connector.
Disconnect the M10 front No. 1 speaker assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| M1-3 - I13-1 (+) | Always | Below 1 Ω |
| M1-1 - I13-2 (-) | Always | Below 1 Ω |
| I13-3 (TWL+) - I41-2 (FL+) | Always | Below 1 Ω |
| I13-4 (TWL-) - I41-6 (FL-) | Always | Below 1 Ω |
| M10-1 - I41-2 (FL+) | Always | Below 1 Ω |
| M10-2 - I41-6 (FL-) | Always | Below 1 Ω |
| M1-3 - Body ground | Always | 10 kΩ or higher |
| M1-1 - Body ground | Always | 10 kΩ or higher |
| I13-3 (TWL+) - Body ground | Always | 10 kΩ or higher |
| I13-4 (TWL-) - Body ground | Always | 10 kΩ or higher |
| M10-1 - Body ground | Always | 10 kΩ or higher |
| M10-2 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (REAR SPEAKER RH CIRCUIT) |
Disconnect the I42 navigation receiver assembly connectors.
Disconnect the N2 rear No. 2 speaker assembly RH connector.
Disconnect the O37 quarter side speaker assembly RH connector.
Disconnect the N1 rear No. 1 speaker assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| N2-3 - O37-3 (+) | Always | Below 1 Ω |
| N2-1 - O37-4 (-) | Always | Below 1 Ω |
| O37-1 (+) - I42-1 (RR+) | Always | Below 1 Ω |
| O37-2 (-) - I42-3 (RR-) | Always | Below 1 Ω |
| N1-1 - I42-1 (RR+) | Always | Below 1 Ω |
| N1-2 - I42-3 (RR-) | Always | Below 1 Ω |
| N2-3 - Body ground | Always | 10 kΩ or higher |
| N2-1 - Body ground | Always | 10 kΩ or higher |
| O37-1 (+) - Body ground | Always | 10 kΩ or higher |
| O37-2 (-) - Body ground | Always | 10 kΩ or higher |
| N1-1 - Body ground | Always | 10 kΩ or higher |
| N1-2 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (REAR SPEAKER LH CIRCUIT) |
Disconnect the I42 navigation receiver assembly connectors.
Disconnect the N8 rear No. 2 speaker assembly LH connector.
Disconnect the O31 quarter side speaker assembly LH connector.
Disconnect the N7 rear No. 1 speaker assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| N8-3 - O31-3 (+) | Always | Below 1 Ω |
| N8-1 - O31-4 (-) | Always | Below 1 Ω |
| O31-1 (+) - I42-2 (RL+) | Always | Below 1 Ω |
| O31-2 (-) - I42-6 (RL-) | Always | Below 1 Ω |
| N7-1 - I42-2 (RL+) | Always | Below 1 Ω |
| N7-2 - I42-6 (RL-) | Always | Below 1 Ω |
| N8-3 - Body ground | Always | 10 kΩ or higher |
| N8-1 - Body ground | Always | 10 kΩ or higher |
| O31-1 (+) - Body ground | Always | 10 kΩ or higher |
| O31-2 (-) - Body ground | Always | 10 kΩ or higher |
| N7-1 - Body ground | Always | 10 kΩ or higher |
| N7-2 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 6.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY |
Remove the front No. 1 speaker assembly (Click here).
Inspect the front No. 1 speaker assembly (Click here).
|
| ||||
| OK | |
| 7.CHECK FRONT NO. 2 SPEAKER ASSEMBLY |
Replace the front No. 2 speaker assembly with a known good one (Click here).
Check that the malfunction disappears.
|
| ||||
| OK | ||
| ||
| 8.CHECK FRONT NO. 3 SPEAKER ASSEMBLY |
Replace the front No. 3 speaker assembly with a known good one (Click here).
Check that the malfunction disappears.
|
| ||||
| OK | ||
| ||
| 9.CHECK REAR NO. 1 SPEAKER ASSEMBLY |
Remove the rear No. 1 speaker assembly (Click here).
Inspect the rear No. 1 speaker assembly (Click here).
|
| ||||
| OK | |
| 10.CHECK REAR NO. 2 SPEAKER ASSEMBLY |
Replace the rear No. 2 speaker assembly with a known good one (Click here).
Check that the malfunction disappears.
|
| ||||
| OK | ||
| ||
| 11.CHECK QUARTER SIDE SPEAKER ASSEMBLY |
Replace the quarter side speaker assembly with a known good one (Click here).
Check that the malfunction disappears.
|
| ||||
| OK | ||
| ||