Home › Vehicle Interior › SEAT › REAR POWER SEAT CONTROL SYSTEM

REAR POWER SEAT CONTROL SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK FOLD SEAT CONTROL ECU LH

B129718E07

  1. Disconnect the O33 and O34 ECU connectors.

  2. Measure the voltage and resistance of the wire harness side connectors.

    Terminal No.
    (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    O33-4 (+B) - O33-8 (GND)
    P - W-B
    Power source (Battery)
    Always
    11 to 14 V
    O33-8 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    O33-9 (GND2) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    O33-10 (+B2) - O33-9 (GND2)
    V - W-B
    Power source (Battery)
    Always
    11 to 14 V
    O34-3 (IG) - O33-8 (GND)
    R - W-B
    Power source (IG)
    Ignition switch ON
    11 to 14 V
    Ignition switch off
    Below 1 V
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the O33 and O34 ECU connectors.

  4. Measure the voltage and resistance of the connectors.

    Terminal No.
    (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    O33-1 (FLD+) - O33-8 (GND)
    B - W-B
    No. 2 reclining motor operation signal
    Ignition switch off or with shift lever on P, ignition switch ON
    Rear power seat switch LH forward on
    11 to 14 V
    O33-2 (RCL+) - O33-8 (GND)
    SB - W-B
    No. 1 reclining motor operation signal
    Ignition switch off or with shift lever on P, ignition switch ON
    Rear power seat switch LH forward on
    11 to 14 V
    O33-5 (FLD-) - O33-8 (GND)
    W - W-B
    No. 2 reclining motor operation signal
    Ignition switch off or with shift lever on P, ignition switch ON
    Rear power seat switch LH backward on
    11 to 14 V
    O33-6 (RCL-) - O33-8 (GND)
    R - W-B
    No. 1 reclining motor operation signal
    Ignition switch off or with shift lever on P, ignition switch ON
    Rear power seat switch LH backward on
    11 to 14 V
    O34-4 (R CL) - O33-8 (GND)
    G - W-B
    Rear door courtesy switch signal
    Rear door courtesy switch LH off
    11 to 14 V
    Rear door courtesy switch LH on
    Below 1 V
    O34-5 (BDCY) - O33-8 (GND)
    V - W-B
    Back door courtesy switch signal
    Back door courtesy switch off
    11 to 14 V
    Back door courtesy switch on
    Below 1 V
    O34-10 (FLD2) - O33-8 (GND)
    BE - W-B
    No. 2 fold switch signal (Folding)
    Rear LH door open
    No. 2 fold seat switch LH off
    11 to 14 V
    Rear LH door open
    No. 2 fold seat switch LH folding on
    Below 1 V
    O34-12 (RCLF) - O33-8 (GND)
    LG - W-B
    Reclining forward switch signal
    Rear power seat switch LH forward off
    11 to 14 V
    Rear power seat switch LH forward on
    Below 1 V
    O34-13 (RCLR) - O33-8 (GND)
    SB - W-B
    Reclining backward switch signal
    Rear power seat switch LH backward off
    11 to 14 V
    Rear power seat switch LH backward on
    Below 1 V
    O34-14 (RTN2) - O33-8 (GND)
    BR - W-B
    No. 2 return switch signal (Return)
    Rear LH door open
    No. 2 fold seat switch LH off
    11 to 14 V
    Rear LH door open
    No. 2 fold seat switch LH return on
    Below 1 V
    O34-15 (RTRN) - O33-8 (GND)
    B - W-B
    No. 1 return switch signal (Return)
    Back door open
    No. 1 fold seat switch LH off
    11 to 14 V
    Back door open
    No. 1 fold seat switch LH return on
    Below 1 V
    O34-16 (FOLD) - O33-8 (GND)
    P - W-B
    No. 1 fold switch signal (Folding)
    Back door open
    No. 1 fold seat switch LH off
    11 to 14 V
    Back door open
    No. 1 fold seat switch LH folding on
    Below 1 V
    O34-22 (SRCL) - O34-36 (SG2)
    G - V
    Reclining position sensor signal
    Motor is operating
    Below 1 V ←→ 11 to 14 V
    Pulse generation
    O34-25 (SV2) - O34-36 (SG2)
    L - V
    Position sensor power supply
    Back door open
    11 to 14 V
    O34-31 (IND3) - O33-8 (GND)
    W - W-B
    No. 2 fold seat switch indicator signal
    Rear LH door open
    No. 2 fold seat switch LH on:
    When the system detects that an object is caught.
    Below 1 V ←→ 11 to 14 V
    Pulse generation
    When the indicator is illuminated
    9 to 13 V
    O34-32 (P) - O33-8 (GND)
    GR - W-B
    Park/Neutral position switch signal
    Ignition switch ON
    Park/Neutral position switch P position
    11 to 14 V
    Ignition switch ON
    Park/Neutral position switch not in P position
    Below 1 V
    O34-35 (IND1) - O33-8 (GND)
    Y - W-B
    No. 1 fold seat switch indicator signal
    Back door open
    No. 1 fold seat switch LH on:
    When the system detects that an object is caught.
    Below 1 V ←→ 11 to 14 V
    Pulse generation
    When the indicator is illuminated
    9 to 13 V
    O34-36 (SG2) - Body ground
    V - Body ground
    Position sensor ground
    Always
    Below 1 Ω
    If the result is not as specified, the ECU may have a malfunction.


CHECK FOLD SEAT CONTROL ECU RH

B129718E08

  1. Disconnect the P19 and P20 ECU connectors.

  2. Measure the voltage and resistance of the wire harness side connectors.

    Terminal No.
    (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    P19-4 (+B) - P19-8 (GND)
    LG - W-B
    Power source (Battery)
    Always
    11 to 14 V
    P19-8 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    P19-9 (GND2) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    P19-10 (+B2) - P19-9 (GND2)
    B - W-B
    Power source (Battery)
    Always
    11 to 14 V
    P20-3 (IG) - P19-8 (GND)
    P - W-B
    Power source (IG)
    Ignition switch ON
    11 to 14 V
    Ignition switch off
    Below 1 V
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the P19 and P20 ECU connectors.

  4. Measure the voltage and resistance of the connectors.

    Terminal No.
    (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    P19-1 (FLD+) - P19-8 (GND)
    G - W-B
    No. 2 reclining motor operation signal
    Ignition switch off or with shift lever on P, ignition switch ON
    Rear power seat switch RH forward on
    11 to 14 V
    P19-2 (RCL+) - P19-8 (GND)
    BE - W-B
    No. 1 reclining motor operation signal
    Ignition switch off or with shift lever on P, ignition switch ON
    Rear power seat switch RH forward on
    11 to 14 V
    P19-5 (FLD-) - P19-8 (GND)
    R - W-B
    No. 2 reclining motor operation signal
    Ignition switch off or with shift lever on P, ignition switch ON
    Rear power seat switch RH backward on
    11 to 14 V
    P19-6 (RCL-) - P19-8 (GND)
    W - W-B
    No. 1 reclining motor operation signal
    Ignition switch off or with shift lever on P, ignition switch ON
    Rear power seat switch RH backward on
    11 to 14 V
    P20-4 (R CL) - P19-8 (GND)
    G - W-B
    Rear door courtesy switch signal
    Rear door courtesy switch RH off
    11 to 14 V
    Rear door courtesy switch RH on
    Below 1 V
    P20-5 (BDCY) - P19-8 (GND)
    G - W-B
    Back door courtesy switch signal
    Back door courtesy switch off
    11 to 14 V
    Back door courtesy switch on
    Below 1 V
    P20-10 (FLD2) - P19-8 (GND)
    BE - W-B
    No. 2 fold switch signal (Folding)
    Rear RH door open
    No. 2 fold seat switch RH off
    11 to 14 V
    Rear RH door open
    No. 2 fold seat switch RH folding on
    Below 1 V
    P20-12 (RCLF) - P19-8 (GND)
    LG - W-B
    Reclining forward switch signal
    Rear power seat switch RH forward off
    11 to 14 V
    Rear power seat switch RH forward on
    Below 1 V
    P20-13 (RCLR) - P19-8 (GND)
    SB - W-B
    Reclining backward switch signal
    Rear power seat switch RH backward off
    11 to 14 V
    Rear power seat switch RH backward on
    Below 1 V
    P20-14 (RTN2) - P19-8 (GND)
    SB - W-B
    No. 2 return switch signal (Return)
    Rear RH door open
    No. 2 fold seat switch RH off
    11 to 14 V
    Rear RH door open
    No. 2 fold seat switch RH return on
    Below 1 V
    P20-15 (RTRN) - P19-8 (GND)
    B - W-B
    No. 1 return switch signal (Return)
    Back door open
    No. 1 fold seat switch RH off
    11 to 14 V
    Back door open
    No. 1 fold seat switch RH return on
    Below 1 V
    P20-16 (FOLD) - P19-8 (GND)
    P - W-B
    No. 1 fold switch signal (Folding)
    Back door open
    No. 1 fold seat switch RH off
    11 to 14 V
    Back door open
    No. 1 fold seat switch RH folding on
    Below 1 V
    P20-22 (SRCL) - P20-36 (SG2)
    G - V
    Reclining position sensor signal
    Motor is operating
    Below 1 V ←→ 11 to 14 V
    Pulse generation
    P20-25 (SV2) - P20-36 (SG2)
    L - V
    Position sensor power supply
    Back door open
    11 to 14 V
    P20-31 (IND3) - P19-8 (GND)
    W - W-B
    No. 2 fold seat switch indicator signal
    Rear RH door open
    No. 2 fold seat switch RH on:
    When the system detects that an object is caught.
    Below 1 V ←→ 11 to 14 V
    Pulse generation
    When the indicator is illuminated
    9 to 13 V
    P20-32 (P) - P19-8 (GND)
    GR - W-B
    Park/Neutral position switch signal
    Ignition switch ON
    Park/Neutral position switch P position
    11 to 14 V
    Ignition switch ON
    Park/Neutral position switch not in P position
    Below 1 V
    P20-35 (IND1) - P19-8 (GND)
    L - W-B
    No. 1 fold seat switch indicator signal
    Back door open
    No. 1 fold seat switch RH on:
    When the system detects that an object is caught.
    Below 1 V ←→ 11 to 14 V
    Pulse generation
    When the indicator is illuminated
    9 to 13 V
    P20-36 (SG2) - Body ground
    V - Body ground
    Position sensor ground
    Always
    Below 1 Ω
    If the result is not as specified, the ECU may have a malfunction.