REAR POWER SEAT CONTROL SYSTEM > Reclining Motor Circuit |

| 1.CHECK POWER SEAT MOTOR (RECLINING MOTOR VOLTAGE) |
![]() |
Disconnect the a1 and a3 or Y1 and Y3 connectors.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| a1-1 (FWD) - Body ground | Ignition switch off or with shift lever on P, ignition switch ON Rear power seat switch LH forward on | 11 to 14 V |
| a1-2 (BACK) - Body ground | Ignition switch off or with shift lever on P, ignition switch ON Rear power seat switch LH backward on | 11 to 14 V |
| a3-1 (FWD) - Body ground | Ignition switch off or with shift lever on P, ignition switch ON Rear power seat switch LH forward on | 11 to 14 V |
| a3-2 (BACK) - Body ground | Ignition switch off or with shift lever on P, ignition switch ON Rear power seat switch LH backward on | 11 to 14 V |
| Tester Connection | Switch Condition | Specified Condition |
| Y1-1 (FWD) - Body ground | Ignition switch off or with shift lever on P, ignition switch ON Rear power seat switch RH forward on | 11 to 14 V |
| Y1-2 (BACK) - Body ground | Ignition switch off or with shift lever on P, ignition switch ON Rear power seat switch RH backward on | 11 to 14 V |
| Y3-1 (FWD) - Body ground | Ignition switch off or with shift lever on P, ignition switch ON Rear power seat switch RH forward on | 11 to 14 V |
| Y3-2 (BACK) - Body ground | Ignition switch off or with shift lever on P, ignition switch ON Rear power seat switch RH backward on | 11 to 14 V |
|
| ||||
| OK | |
| 2.INSPECT POWER SEAT MOTOR (RECLINING MOTOR) |
![]() |
Remove the power seat motors (reclining motor) (Click here).
Check the operation of the No. 1 reclining motor.
Check if the seat moves smoothly when the battery is connected to the reclining motor connector terminals.
| Measurement Condition | Specified Condition |
| Battery positive (+) → 1 Battery negative (-) → 2 | Motor gear rotates clockwise |
| Battery positive (+) → 2 Battery negative (-) → 1 | Motor rear rotates counterclockwise |
![]() |
Check the operation of the No. 2 reclining motor.
Check if the seat moves smoothly when the battery is connected to the reclining motor connector terminals.
| Measurement Condition | Specified Condition |
| Battery positive (+) → 1 Battery negative (-) → 2 | Motor gear rotates clockwise |
| Battery positive (+) → 2 Battery negative (-) → 1 | Motor rear rotates counterclockwise |
|
| ||||
| OK | ||
| ||
| 3.CHECK HARNESS AND CONNECTOR (FOLD SEAT CONTROL ECU - RECLINING MOTOR) |
![]() |
Disconnect the O33 or P19 ECU connector.
Disconnect the a1 or Y1 motor connector.
Disconnect the a3 or Y3 motor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| O33-1 (FLD+) - a3-1 (FWD) | Always | Below 1 Ω |
| O33-1 (FLD+) - Body ground | Always | 10 kΩ or higher |
| O33-2 (RCL+) - a1-1 (FWD) | Always | Below 1 Ω |
| O33-2 (RCL+) - Body ground | Always | 10 kΩ or higher |
| O33-5 (FLD-) - a3-2 (BACK) | Always | Below 1 Ω |
| O33-5 (FLD-) - Body ground | Always | 10 kΩ or higher |
| O33-6 (RCL-) - a1-2 (BACK) | Always | Below 1 Ω |
| O33-6 (RCL-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| P19-1 (FLD+) - Y3-1 (FWD) | Always | Below 1 Ω |
| P19-1 (FLD+) - Body ground | Always | 10 kΩ or higher |
| P19-2 (RCL+) - Y1-1 (FWD) | Always | Below 1 Ω |
| P19-2 (RCL+) - Body ground | Always | 10 kΩ or higher |
| P19-5 (FLD-) - Y3-2 (BACK) | Always | Below 1 Ω |
| P19-5 (FLD-) - Body ground | Always | 10 kΩ or higher |
| P19-6 (RCL-) - Y1-2 (BACK) | Always | Below 1 Ω |
| P19-6 (RCL-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||