Home › Vehicle Interior › SEAT › REAR POWER SEAT CONTROL SYSTEM

REAR POWER SEAT CONTROL SYSTEM > Rear Power Seat Switch Circuit

for Preparation Click here


DESCRIPTION

When the rear power seat switch is operated, a recline signal is sent to the fold seat control ECU. The ECU activates the power seat motor based on the signal from the rear power seat switch.

WIRING DIAGRAM


B193763E02


INSPECTION PROCEDURE

1.CHECK FOLD SEAT CONTROL ECU (INPUT SIGNAL)


    B193667E13
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for LH side 
    Tester Connection
    Switch Condition
    Specified Condition
    O34-12 (RCLF) - Body ground
    Rear power seat switch LH forward off
    11 to 14 V
    Rear power seat switch LH forward on
    Below 1 V
    O34-13 (RCLR) - Body ground
    Rear power seat switch LH backward off
    11 to 14 V
    Rear power seat switch LH backward on
    Below 1 V
    for RH side 
    Tester Connection
    Switch Condition
    Specified Condition
    P20-12 (RCLF) - Body ground
    Rear power seat switch RH forward off
    11 to 14 V
    Rear power seat switch RH forward on
    Below 1 V
    P20-13 (RCLR) - Body ground
    Rear power seat switch RH backward off
    11 to 14 V
    Rear power seat switch RH backward on
    Below 1 V



NG
Go to step 2
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE 

2.INSPECT REAR POWER SEAT SWITCH


    B193752E01
  1. Remove the rear power seat switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    4 (FWD) - 6 (E)
    Rear power seat switch forward off
    10 kΩ or higher
    Rear power seat switch forward on
    Below 1 Ω
    5 (BACK) - 6 (E)
    Rear power seat switch backward off
    10 kΩ or higher
    Rear power seat switch backward on
    Below 1 Ω



NG
REPLACE REAR POWER SEAT SWITCH (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (FOLD SEAT CONTROL ECU - REAR POWER SEAT SWITCH)


    B195045E02
  1. Disconnect the O34 or P20 ECU connector.

  1. Disconnect the O29 or P13 switch connector.

  1. Disconnect the connector from the folding motor.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LH Side 
    Tester Connection
    Condition
    Specified Condition
    O34-12 (RCLF) - O29-4 (FWD)
    Always
    Below 1 Ω
    O34-12 (RCLF) - Body ground
    Always
    10 kΩ or higher
    O34-13 (RCLR) - O29-5 (BACK)
    Always
    Below 1 Ω
    O34-13 (RCLR) - Body ground
    Always
    10 kΩ or higher
    for RH Side 
    Tester Connection
    Condition
    Specified Condition
    P20-12 (RCLF) - P13-4 (FWD)
    Always
    Below 1 Ω
    P20-12 (RCLF) - Body ground
    Always
    10 kΩ or higher
    P20-13 (RCLR) - P13-5 (BACK)
    Always
    Below 1 Ω
    P20-13 (RCLR) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (REAR POWER SEAT SWITCH - BODY GROUND)