Home › Vehicle Exterior › DOOR / HATCH › POWER BACK DOOR SYSTEM

POWER BACK DOOR SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST

HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body / Back Door or Main Body / Data List.

  5. According to the display on the intelligent tester, read the Data List.

    Back Door (Power Back Door ECU) 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Door Lock Status
    Back door lock condition signal / LOCK or UNLOCK
    LOCK: Back door is locked
    UNLOCK: Back door is unlocked
    -
    Half Latch SW
    Half-latch switch signal / ON or OFF
    ON: Back door lock motor is open-latch or over-latch
    OFF: Back door lock motor is full-latch or half-latch
    -
    Closer Position SW
    Closer position switch signal / ON or OFF
    ON: Back door lock center gear is in center position
    OFF: Back door lock center gear is out of center position
    -
    Courtesy SW
    Back door courtesy switch signal / ON or OFF
    ON: Back door is open
    OFF: Back door is closed
    -
    PBD Touch Sensor (Right)
    Power back door touch sensor RH signal / ON or OFF
    ON: Power back door touch sensor RH pressed
    OFF: Power back door touch sensor RH not pressed
    -
    PBD Touch Sensor (Left)
    Power back door touch sensor LH signal / ON or OFF
    ON: Power back door touch sensor LH pressed
    OFF: Power back door touch sensor LH not pressed
    -
    PBD Close SW
    Power back door closer switch signal / ON or OFF
    ON: Power back door closer switch is on
    OFF: Power back door closer switch is off
    -
    IG SW
    Ignition switch signal / ON or OFF
    ON: Ignition switch ON
    OFF: Ignition switch off or ACC
    -
    PBD Position (3/4 - Open) - Open
    Back door position (3/4 open - Full open) / CAUTION or OK
    CAUTION: Back door position is not 3/4 opened - fully opened OK: Back door position is 3/4 opened - fully opened
    OK: Back door position is 3/4 opened - fully opened
    -
    PBD Position (2/4 - 3/4) - 3/4
    Back door position (2/4 open - 3/4 open) / CAUTION or OK
    CAUTION: Back door position is not 2/4 opened - 3/4 opened
    OK: Back door position is 2/4 opened - 3/4 opened
    -
    PBD Position (1/4 - 2/4) - 2/4
    Back door position (1/4 open - 2/4 open) / CAUTION or OK
    CAUTION: Back door position is not 1/4 opened - 2/4 opened
    OK: Back door position is 1/4 opened - 2/4 opened
    -
    PBD Position (close - 1/4) - 1/4
    Back door position (Full close - 1/4 open) / CAUTION or OK
    CAUTION: Back door position is not fully closed - 1/4 opened
    OK: Back door position is fully closed - 1/4 opened
    -

    Main Body (Main Body ECU) 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Back Door Open
    Back door lock / Permit or Prohibit
    Permit: Back door is unlocked
    Prohibit: Back door is locked
    -
    Back Door Open SW
    Back door control switch / ON or OFF
    ON: Back door control switch is pushed
    OFF: Back door control switch is not pushed
    -


ACTIVE TEST

HINT:
Using the intelligent tester to perform Active Test allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body / Back Door / Active Test.

  5. According to the display on the intelligent tester, perform the Active Test.

    Back Door (Power Back Door ECU) 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Latch Release
    Latch release operation
    ON / OFF
    -
    PBD Motor
    Power back door motor
    ON / OFF
    -
    PBD Clutch
    Power back door motor clutch
    ON / OFF
    -
    PBD Buzzer
    Power back door buzzer sound
    ON / OFF
    -