Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM

THEFT DETERRENT SYSTEM > SYSTEM DESCRIPTION

for Preparation Click here



OUTLINE OF THEFT DETERRENT SYSTEM
  1. The theft deterrent system can be set by locking the doors using the transmitter or key, or by opening and closing the doors (refer to Active Arming Mode).
  2. The alarm function will be activated when someone attempts to forcibly unlock any of the doors or open any of the doors, engine hood, or back door, while the system is in the armed state.
  3. In the alarm sounding state, the system blinks the hazard warning lights. At the same time, the system sounds the vehicle horn(s) and security horn to deter break-in and theft as well as to warn people around the vehicle.
  4. The alarm can be canceled by unlocking the doors using the transmitter or key.
  5. Active arming mode has 4 states: disarmed state, arming preparation state, armed state and alarm sounding state.
  1. Disarmed state:

    1. The alarm function is not operating.
    2. The theft deterrent system is not operating.

  2. Arming preparation state:

    1. The time until the system goes into the armed state.
    2. The theft deterrent system is not operating.

  3. Armed state:

    1. The theft deterrent system is operating.

  4. Alarm sounding state:

    1. The alarm function is operating.

    Alarm time:
    Approximately 30 seconds.


    Refer to the Table Below for Alarm Methods and Time 
    Alarm Method
    Hazard Warning Lights
    Flashing
    Vehicle Horn(s)
    Sounding
    (approximately 0.4 second cycles)
    Security Horn
    Sounding
    (approximately 0.4 second cycles)
    Alarm Time
    Approximately 30 seconds

    HINT:
    If any of the doors are unlocked when the key is not in the key cylinder during the armed state, a forced door lock signal will be output (refer to Forced Door Lock Control).


FUNCTION OF MAIN COMPONENTS

Component
Function
Security indicator
Informs driver of theft deterrent system status.
Security horn
Sounds when attempted break-in or theft is detected.
Hazard warning lights
Begin flashing when attempted break-in or theft is detected.
Vehicle horn(s)
Sounds when attempted break-in or theft is detected.
Door courtesy light switch
Detects door status (open or closed).
Door unlock detection switch
Detects door status (locked or unlocked).
Engine hood courtesy switch
Detects engine hood status (open or closed).
Back door courtesy switch
Detects back door status (open or closed).

ACTIVE ARMING MODE

HINT:
Active arming mode starts the alarm control immediately after the doors are locked.



  1. Active arming mode:
    This system operates as described in the diagram below when one of the items for the relevant condition is met.


    B112141E03

    HINT:
    The terms "all doors" and "door" below also refer to the back door.


    Condition
    Item
    Condition (1)
    In the disarmed state, the system state is switched if one of the following conditions is met when the key is not in the key cylinder:
    1. With all doors and engine hood closed, all doors are locked by key operation.
    2. With all doors and engine hood closed, all doors are locked by wireless operation.
    3. With the engine hood closed, all doors are closed and locked without using the key.
    Condition (2)
    Approximately 30 seconds elapse after condition (1) is met.
    Condition (3)
    1. A wireless unlock signal is received.
    2. The driver door only or all doors are unlocked by key operation.
    3. Any door is unlocked.
    4. Any door is opened.
    5. The key is inserted into the ignition key cylinder.
    6. The ignition switch is turned to ON or ACC.
    7. The battery is reconnected.
    Condition (4)
    1. The engine hood is opened.
    2. The battery is reconnected.
    3. Any door is unlocked without the key when all doors are locked.
    4. The ignition switch is turned to ON without using the key.
    Condition (5)
    1. A wireless unlock signal is received.
    2. The driver door only or all doors are unlocked by key operation.
    3. The ignition switch is turned to ON and the engine is run for more than 2 seconds.
    Condition (6)
    Approximately 30 seconds elapse. The alarm stops and the system returns to the armed state.


FORCED DOOR LOCK CONTROL
  1. The forced door lock control prevents the vehicle from being tampered with. Immediately after a door is unlocked (alarm starts), all doors are forced to lock by a forced door lock signal.

    1. Conditions that force the doors to lock:
      The key is not in the key cylinder and both of the following conditions are met:

      1. The theft deterrent system is in the alarm sounding state of active arming mode.
      2. Any door is unlocked.


PANIC ALARM CONTROL
  1. The panic alarm control makes it possible to voluntarily set off the panic alarm by pressing the PANIC switch on the wireless transmitter.

    1. Conditions that cause the panic alarm control to set off the panic alarm:
      The PANIC switch on the wireless transmitter is pressed under the following conditions:

      1. The ignition switch is off.
      2. The theft deterrent system is not in the alarm sounding state.

      HINT:
      For details about the alarm sounding state, refer to Active Arming Mode.

    2. Conditions that cause the panic alarm control to shut off the alarm:
      Any of the following conditions is met during panic alarm operation:

      1. The ignition switch is turned to ON.
      2. The PANIC switch is pressed again.
      3. Any of the switches on the wireless transmitter (LOCK/UNLOCK or POWER BACK DOOR*) is pressed.
      4. The panic alarm ends (approximately 30 sec. have passed).
      5. The theft deterrent system switches to the alarm sounding state. Under this condition, the theft deterrent system is controlling the alarm rather than the panic alarm control. In order to cancel this alarm, refer to the theft deterrent system alarm sounding state cancellation procedure.

      HINT:
      1. *: w/ Power Back Door
      2. For details about the alarm sounding state, refer to Active Arming Mode.


SECURITY INDICATOR OUTPUT
  1. The main body ECU outputs a signal to turn on the security indicator according to the state of the theft deterrent system. However, some of the actual lighting conditions of the security indicator are different from the output signals of the main body ECU.

    Output 
    State of Theft Deterrent System
    Security Indicator
    Output Signal from Main Body ECU
    Actual Lighting Condition
    Disarmed state
    OFF
    OFF (Immobiliser system unset)
    BLINKING (Immobiliser system set)
    Arming preparation state
    ON
    ON
    Armed state
    OFF
    BLINKING
    Alarm sounding state
    ON
    ON
    Blinking Cycle 
    Time
    Security Indicator
    0.2 sec.
    ON
    1.8 sec.
    OFF

    HINT:
    When the immobiliser system is set, the security indicator blinks during both the disarmed state and the armed state, due to output signals from the immobiliser system.