Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM

POWER WINDOW CONTROL SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

B158006E67

  1. Disconnect the M3 power window regulator motor LH connector.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    M3-2 (B) - Body ground
    G - Body ground
    Battery power supply
    Always
    11 to 14 V
    M3-1 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the M3 power window regulator motor LH connector.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    M3-10 (UP) - M3-1 (GND)
    BE - W-B
    Power window UP operation
    Ignition switch ON
    Power window regulator master switch
    OFF → UP
    11 to 14 V → Below 1 V
    M3-10 (UP) - M3-1 (GND)
    BE - W-B
    Power window UP operation
    Ignition switch ON
    door glass fully open → power window AUTO UP operation → the door glass fully closed
    11 to 14 V → Below 1 V → 11 to 14 V
    M3-7 (DOWN) - M3-1 (GND)
    SB - W-B
    Power window DOWN operation
    Ignition switch ON
    Power window regulator master switch
    OFF → DOWN
    11 to 14 V → Below 1 V
    M3-7 (DOWN) - M3-1 (GND)
    SB - W-B
    Power window DOWN operation
    Ignition switch ON
    door glass fully closed → power window AUTO DOWN operation → the door glass fully closed
    11 to 14 V → Below 1 V → 11 to 14 V
    M3-9 (LIN) - M3-1 (GND)
    W - W-B
    LIN communication signal
    Ignition switch ON
    Pulse generation
    If the result is not as specified, the motor may be malfunctioning.


CHECK FRONT POWER WINDOW REGULATOR MOTOR RH

B158006E68

  1. Disconnect the L3 power window regulator motor RH connector.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    L3-2 (B) - Body ground
    V - Body ground
    Battery power supply
    Always
    11 to 14 V
    L3-1 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the L3 power window regulator motor RH connector.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    L3-10 (UP) - L3-1 (GND)
    G - W-B
    Power window UP operation
    Ignition switch ON
    power window regulator switch
    OFF → UP
    11 to 14 V → Below 1 V
    L3-10 (UP) - L3-1 (GND)
    G - W-B
    Power window UP operation
    Ignition switch ON
    door glass fully open → power window AUTO UP operation → the door glass fully closed
    11 to 14 V → Below 1 V → 11 to 14 V
    L3-7 (DOWN) - L3-1 (GND)
    P - W-B
    Power window DOWN operation
    Ignition switch ON
    power window regulator switch
    OFF → DOWN
    11 to 14 V → Below 1 V
    L3-7 (DOWN) - L3-1 (GND)
    P - W-B
    Power window DOWN operation
    Ignition switch ON
    door glass fully closed → power window AUTO DOWN operation → the door glass fully closed
    11 to 14 V → Below 1 V → 11 to 14 V
    L3-9 (LIN) - L3-1 (GND)
    L - W-B
    LIN communication signal
    Ignition switch ON
    Pulse generation
    L3-4 (AUTO) - L3-1 (GND)
    B - W-B
    Power window AUTO UP/DOWN operation
    Ignition switch ON
    power window regulator switch
    OFF → AUTO UP/DOWN operation
    11 to 14 V → Below 1 V
    If the result is not as specified, the motor may be malfunctioning.


CHECK POWER WINDOW REGULATOR MASTER SWITCH

B191457E01

  1. Disconnect the M2 power window regulator master switch connector.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    M2-3 (B) - Body ground
    L - Body ground
    Battery power supply
    Always
    11 to 14 V
    M2-13 (B) - Body ground
    P - Body ground
    Battery power supply
    Ignition switch ON
    11 to 14 V
    M2-1 (E) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the M2 power window regulator master switch connector.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    M2-4 (UP) - M2-1 (E)
    BE - W-B
    Driver side door power window UP operation
    Ignition switch ON, driver side door power window regulator switch OFF → UP
    11 to 14 V → Below 1 V
    M2-4 (UP) - M2-1 (E)
    BE - W-B
    Driver side door power window AUTO UP operation
    Ignition switch ON, driver side door glass fully closed → power window AUTO UP operation → driver side door glass fully open
    11 to 14 V → Below 1 V → 11 to 14 V
    M2-5 (DOWN) - M2-1 (E)
    SB - W-B
    Driver side door power window DOWN operation
    Ignition switch ON, driver side door power window regulator switch OFF → DOWN
    11 to 14 V → Below 1 V
    M2-5 (DOWN) - M2-1 (E)
    SB - W-B
    Driver side door power window AUTO DOWN operation
    Ignition switch ON, driver side door glass fully closed → power window AUTO DOWN operation → driver side door glass fully open
    11 to 14 V → Below 1 V → 11 to 14 V
    M2-12 (U) - M2-1 (E)
    V - W-B
    Rear LH side door power window UP operation
    Ignition switch ON, rear LH side door power window regulator switch OFF → UP
    Below 1 V → 11 to 14 V
    M2-15 (D) - M2-1 (E)
    B - W-B
    Rear LH side door power window DOWN operation
    Ignition switch ON, rear LH side door power window regulator switch OFF → DOWN
    Below 1 V → 11 to 14 V
    M2-10 (U) - M2-1 (E)
    BE - W-B
    Rear RH side door power window UP operation
    Ignition switch ON, rear RH side door power window regulator switch OFF → UP
    Below 1 V → 11 to 14 V
    M2-16 (D) - M2-1 (E)
    LG - W-B
    Rear RH side door power window DOWN operation
    Ignition switch ON, rear RH side door power window regulator switch OFF → DOWN
    Below 1 V → 11 to 14 V
    M2-6 (LIN1) - M2-1 (E)
    L - W-B
    LIN communication signal
    Ignition switch ON
    Pulse generation
    M2-7 (LIN2) - M2-1 (E)
    W - W-B
    LIN communication signal
    Ignition switch ON
    Pulse generation
    If the result is not as specified, the power window regulator master switch may be malfunctioning.


CHECK MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)

B174142E05

  1. Disconnect the DD, H3 and H4 main body ECU connectors.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    DD-62 (GND1, GND2) - Body ground
    W-B - Body ground
    Body ground
    Always
    Below 1 Ω
    H3-21 (PCTY) - Body ground
    BE - Body ground
    Front door courtesy light switch RH signal
    Front door RH open → closed
    Below 1 Ω → 10 kΩ or higher
    H4-24 (DCTY) - Body ground
    BR - Body ground
    Front door courtesy light switch LH signal
    Front door LH open → closed
    Below 1 Ω → 10 kΩ or higher
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the DD, H3 and H4 main body ECU connectors.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    DB-13 (BECU) - Body ground
    GR - Body ground
    BECU power supply
    Always
    11 to 14 V
    DD-43 (IG) - Body ground
    B - Body ground
    IG signal
    Ignition switch ON
    11 to 14 V
    H2-10 (LIN2) - DD-62 (GND1, GND2)
    V - W-B
    LIN communication signal
    Ignition switch ON
    Pulse generation
    If the result is not as specified, there may be a malfunction on the wire harness side.


CHECK BACK DOOR ECU (MULTIPLEX NETWORK BODY ECU)

E157854E01

  1. Disconnect the V2 and V3 back door ECU connectors.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    V2-7 (BECU) - Body ground
    GR - Body ground
    Battery power supply
    Always
    11 to 14 V
    V2-8 (SIG) - Body ground
    Y - Body ground
    IG power supply
    Ignition switch off
    Below 1 V
    Ignition switch ON
    11 to 14 V
    V2-6 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    V3-7 (BKUL) - V3-19 (KEYE)
    LG - BE
    Back door key cylinder linked switch signal
    Back door key cylinder turned UNLOCK
    Below 1 Ω
    V3-8 (BKL) - V3-19 (KEYE)
    G - BE
    Back door key cylinder linked switch signal
    Back door key cylinder turned LOCK
    Below 1 Ω
    V3-17 (P) - V3-25 (SGND)
    V - G
    Rear wiper retractable position switch signal
    Rear wiper motor retractable position
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the V2 and V3 back door ECU connectors.

  4. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    V2-16 (MPX1) - V2-6 (GND)
    Y - W-B
    LIN communication signal
    Ignition switch ON
    Pulse generation
    V2-21 (A UP) - V2-6 (GND)
    G - W-B
    Back door power window AUTO UP signal
    Ignition switch ON
    Back door power window switch
    OFF → AUTO UP
    Pulse generation → Below 1 V
    V2-22 (BUP) - V2-6 (GND)
    BE - W-B
    Back door power window UP signal
    Ignition switch ON
    Back door power window switch
    OFF → UP
    Pulse generation → Below 1 V
    V2-23 (BDN) - V2-6 (GND)
    V - W-B
    Back door power window DOWN signal
    Ignition switch ON
    Back door power window switch
    OFF → DOWN
    Pulse generation → Below 1 V
    V2-24 (A DN) - V2-6 (GND)
    L - W-B
    Back door power window AUTO DOWN signal
    Ignition switch ON
    Back door power window switch
    OFF → AUTO DOWN
    Pulse generation → Below 1 V
    V3-5 (BDUP) - V2-6 (GND)
    BE - W-B
    Back door power window UP operation signal
    Ignition switch ON
    Back door power window switch
    OFF → UP
    Below 1 V → 11 to 14 V
    V3-6 (BDDN) - V2-6 (GND)
    P - W-B
    Back door power window DOWN operation signal
    Ignition switch ON
    Back door power window switch
    OFF → DOWN
    Below 1 V → 11 to 14 V
    V3-12 (DSV) - V3-23 (DSG)
    LG - SB
    Power supply for Hall-IC
    Ignition switch ON
    8.5 to 16 V
    V3-13 (DS1) - V3-23 (DSG)
    L - SB
    Back door window glass position signal
    Back door power window operation
    Pulse generation
    V3-14 (DS2) - V3-23 (DSG)
    Y - SB
    Back door window glass position signal
    Back door power window operation
    Pulse generation
    V3-19 (KEYE) - V2-6 (GND)
    BE - W-B
    Ground for back door key cylinder switch
    Always
    Below 1 Ω
    V3-23 (DSG) - V2-6 (GND)
    SB - W-B
    Ground for Hall-IC
    Always
    Below 1 Ω
    V3-25 (SGND) - V2-6 (GND)
    G - W-B
    Ground for rear wiper reverse position and rear wiper retractable position switch
    Always
    Below 1 Ω
    If the result is not as specified, the back door ECU may be malfunctioning.