REAR AIR CONDITIONING UNIT > INSTALLATION |
| 1. INSTALL REAR COOLING UNIT ASSEMBLY |
![]() |
Install the rear cooling unit with the 3 bolts and nut.
![]() |
Connect the 4 connectors.
Attach the 3 clamps.
| 2. INSTALL FOLD SEAT CONTROL ECU |
![]() |
Install the fold seat control ECU with the 2 nuts.
Connect the 2 connectors.
| 3. INSTALL AMPLIFIER ANTENNA ASSEMBLY |
![]() |
Install the amplifier antenna with the bolt.
| 4. INSTALL REAR SIDE NO. 1 AIR DUCT |
![]() |
Install the air duct with the clip.
Attach the clamp.
| 5. INSTALL COVER SUB-ASSEMBLY |
![]() |
Attach the 2 claws to install the cover.
| 6. INSTALL QUARTER TRIM BRACKET RH |
![]() |
Install the quarter trim bracket with the 2 bolts.
Attach the clamp.
| 7. INSTALL REAR SIDE NO. 2 AIR DUCT |
![]() |
Install the air duct with the 2 clips.
| 8. INSTALL REAR WINDOW NO. 2 SIDE GARNISH ASSEMBLY RH |
![]() |
Attach the 5 clips to install the rear window No. 2 side garnish assembly RH.
Install the bolt.
![]() |
Attach the claw to install the cover.
| 9. INSTALL REAR WINDOW SIDE GARNISH ASSEMBLY RH |
![]() |
Pass the rear seat outer belt floor anchor through the rear window side garnish.
Attach the 5 clips to install the rear window side garnish.
Install the bolt.
![]() |
Attach the claw to install the cover.
| 10. INSTALL QUARTER TRIM PANEL ASSEMBLY RH (for Standard) |
![]() |
Detach the 3 claws and remove the outer lap belt anchor cover.
![]() |
Remove the bolt and outer lap belt anchor.
![]() |
Remove the bolt and outer lap belt anchor.
![]() |
Using a screwdriver with its tip wrapped in protective tape, detach the 2 claws and remove the cover.
Remove the 2 bolts and 2 clips.
Detach the 11 clips.
Disconnect the connector and remove the quarter trim panel.

| 11. INSTALL QUARTER TRIM PANEL ASSEMBLY RH (for Power Seat) |
Connect the 3 connectors.
Attach the 11 clips to install the quarter trim panel.
Install the 2 bolts.
Install the 2 clips.

![]() |
Attach the 2 claws to install the cover.
![]() |
Install the outer lap belt anchor with the bolt.
![]() |
Install the outer lap belt anchor with the bolt.
![]() |
Attach the 3 claws to install the outer lap belt anchor cover.
| 12. INSTALL REAR FLOOR MAT SUPPORT PLATE |
![]() |
Attach the 5 clips and 4 claws to install the rear floor mat support plate.
| 13. INSTALL ROPE HOOK ASSEMBLY |
![]() |
Install the rope hook with the bolt.
![]() |
Attach the 2 claws to install the cover.
| 14. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH |
![]() |
Align the location mark with the paint mark first, and install the rear door opening trim weatherstrip, as shown in the illustration.
| Area | Color |
| RH side | Pink |
| LH side | Purple |
| 15. INSTALL REAR DOOR SCUFF PLATE RH |
![]() |
Attach the 2 claws and 5 clips to install the rear door scuff plate.
Install the 2 bolts.
![]() |
Attach the 6 claws, 5 clips and 2 guides to install the rear door scuff plate.
Install the bolt.
| 16. INSTALL REAR FLOOR STEP NO. 1 COVER |
![]() |
Attach the 2 claws to install the rear floor step No. 1 cover.
| 17. INSTALL REAR FLOOR STEP NO. 2 COVER |
![]() |
Attach the 2 claws to the install the rear floor step No. 2 cover.
| 18. INSTALL REAR SEAT CUSHION HINGE LOWER COVER RH |
![]() |
Attach the 2 clips and 5 claws to install the rear cushion hinge lower cover RH.
| 19. INSTALL REAR NO. 2 SEAT ASSEMBLY RH (for Power Seat) |
Place the rear No. 2 seat assembly RH in the cabin.
![]() |
Insert the 2 locating pins through the 2 body holes and make sure that the inner and outer seat tracks are locked securely.
Install the 2 bolts.
Connect the seat wire connector.
![]() |
Install the 2 bolts.
| 20. INSTALL REAR NO. 2 SEAT ASSEMBLY RH (for Manual Seat) |
Place the rear No. 2 seat assembly RH in the cabin.
![]() |
Insert the 2 locating pins through the 2 body holes and make sure that the inner and outer seat tracks are locked securely.
Install the 2 bolts.
![]() |
Install the 2 bolts.
| 21. INSTALL SEAT TRACK BRACKET FRONT COVER INNER |
![]() |
Attach the 2 guides, claw and clip in the order shown in the illustration, and then install the seat track bracket front cover inner.
| 22. INSTALL SEAT TRACK BRACKET FRONT COVER OUTER |
![]() |
Attach the 2 guides and 2 claws in the order shown in the illustration, and then install the seat track bracket front cover outer.
| 23. INSTALL DECK BOARD BRACKET |
![]() |
Install the deck board bracket with the 2 bolts.
| 24. INSTALL DECK BOARD REINFORCEMENT SUB-ASSEMBLY |
![]() |
Install the deck board reinforcement with the 4 bolts.
| 25. INSTALL NO. 1 DECK BOARD SUB-ASSEMBLY |
![]() |
Attach the 5 clips to install the No. 1 deck board.
| 26. INSTALL ROPE HOOK ASSEMBLY |
![]() |
Install the rope hook with the bolt.
| 27. INSTALL LUGGAGE COMPARTMENT TRIM BOX |
![]() |
Install the luggage compartment trim box with the 4 bolts.
![]() |
Install the 4 caps.
| 28. INSTALL NO. 2 DECK BOARD SUB-ASSEMBLY |
![]() |
Attach the 4 guides to install the No. 2 deck board.
| 29. CONNECT COOLER REFRIGERANT LIQUID PIPE D |
Remove the attached vinyl tape from the pipe.
Sufficiently apply compressor oil to a new O-ring and the fitting surface of the cooler refrigerant liquid pipe.
Install the O-ring on the cooler refrigerant liquid pipe.
Install the cooler refrigerant liquid pipe.
| 30. CONNECT COOLER REFRIGERANT SUCTION PIPE B |
Remove the attached vinyl tape from the pipe.
Sufficiently apply compressor oil to a new O-ring and the fitting surface of the cooler refrigerant suction pipe.
Install the O-ring on the cooler refrigerant suction pipe.
Move the hook connector in the direction indicated by the arrow in the illustration.
![]() |
Insert the pipe joint into the fitting hole securely and tighten the bolt.
| 31. CONNECT HEATER WATER OUTLET HOSE E |
![]() |
Connect the water hose onto the cooling unit.
| 32. CONNECT HEATER WATER INLET HOSE H |
![]() |
Connect the water hose onto the cooling unit.
| 33. ADD ENGINE COOLANT |
Add engine coolant.
![]() |
Slowly pour coolant into the radiator reservoir until it reaches the FULL line.
Install the reservoir cap.
Press the inlet and outlet radiator hoses several times by hand, and then check the coolant level. If the coolant level is low, add coolant.
Install the radiator cap.
Start the engine and warm it up until the thermostat opens.
Maintain the engine speed at 2000 to 2500 rpm.
Press the inlet and outlet radiator hoses several times by hand to bleed air.
Stop the engine, and wait until the engine coolant cools down to ambient temperature.
![]() |
Check that the coolant level is between the FULL and LOW lines.
If the coolant level is below the LOW line, repeat all of the procedures above.
If the coolant level is above the FULL line, drain coolant so that the coolant level is between the FULL and LOW lines.
| 34. INSPECT FOR COOLANT LEAK |
![]() |
Fill the radiator with coolant and attach a radiator cap tester.
Warm up the engine.
Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop.
If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and head.
| 35. CHARGE REFRIGERANT |

Perform vacuum purging using a vacuum pump.
Charge refrigerant HFC-134a (R134a).
| Cool Box | Refrigerant Charging Amount |
| w/ Cool Box | 1080 to 1140 g (38.1 to 40.2 oz.) |
| w/o Cool Box | 920 to 980 g (32.4 to 34.6 oz.) |

Install the caps onto the service valves on the refrigerant line.
| 36. WARM UP ENGINE |
| 37. INSPECT FOR REFRIGERANT LEAK |
After recharging the refrigerant gas, check for refrigerant gas leakage using a halogen leak detector.
Perform the operation as follows:
![]() |
Using the halogen leak detector, check the refrigerant line, especially at the connection points, for leakage.
If no gas leakage is detected from the drain hose, remove the blower motor from the cooling unit. Insert the halogen leak detector sensor into the unit and perform the test.
Disconnect the pressure switch connector and leave it for approximately 20 minutes. Bring the halogen leak detector close to the pressure switch and perform the test.
| 38. INSTALL ENGINE UNDER COVER NO.1 |
![]() |
Hook the engine under cover to the vehicle body as shown in the illustration.
Install the 3 screws and 5 bolts.