Home › Vehicle Interior › HEATING / AIR CONDITIONING › REAR AIR CONDITIONING UNIT

REAR AIR CONDITIONING UNIT > REMOVAL

for Preparation Click here



1. REMOVE NO. 1 ENGINE UNDER COVER


    A150108
  1. Remove the 3 screws and 5 bolts.

  1. Unhook the engine under cover from the vehicle body as shown in the illustration.



2. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

HINT:
Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. Loosen the radiator drain cock plug.

  1. Remove the radiator cap. Then drain the coolant from the radiator.

  1. Loosen the 2 cylinder block drain cock plugs. Then drain the coolant from the engine.

  1. Tighten the 2 cylinder block drain cock plugs.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }



  1. Tighten the radiator drain cock plug by hand.


    A151835E01



3. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM
  1. Start up the engine.

  1. Switch A/C ON.

  1. Turn the blower switch to ON.

  1. Operate the cooler compressor with an engine speed of approximately 1000 rpm for 5 to 6 minutes to circulate the refrigerant and collect the remaining compressor oil from each component, in the cooler compressor.

  1. Stop the engine.



    E181845E02
  1. Remove the caps from the service valves on the refrigerant line.
    Text in Illustration 
    *1
    Low Pressure Service Valve
    *2
    High Pressure Service Valve

  1. Connect the refrigerant recovery unit.

  1. Recover the refrigerant from the air conditioning system using a refrigerant recovery unit.

    NOTICE:
    Use the refrigerant recovery unit in accordance with the manufacturer's instruction manual.



4. DISCONNECT HEATER WATER INLET HOSE H


    I104295
  1. Using pliers, grip the claws of the clip and slide the clip to disconnect the water hose.

    NOTICE:
    1. Do not apply excessive force to the rear heater outlet water hose.
    2. Prepare a drain pan or cloth in case the coolant leaks.



5. DISCONNECT HEATER WATER OUTLET HOSE E


    I104297
  1. Using pliers, grip the claws of the clip and slide the clip to disconnect the water hose.

    NOTICE:
    1. Do not apply excessive force to the rear heater inlet water hose.
    2. Prepare a drain pan or cloth in case the coolant leaks.



6. DISCONNECT COOLER REFRIGERANT SUCTION PIPE B


    I104299
  1. Remove the bolt, and slide the hook connector.

  1. Disconnect the cooler refrigerant suction pipe.

  1. Remove the O-ring from the cooler refrigerant suction pipe.

    NOTICE:
    Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



7. DISCONNECT COOLER REFRIGERANT LIQUID PIPE D
  1. Disconnect the cooler refrigerant liquid pipe.

  1. Remove the O-ring from the cooler refrigerant liquid pipe.

    NOTICE:
    Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



8. REMOVE NO. 2 DECK BOARD SUB-ASSEMBLY


    B190118
  1. Raise the handle, detach the 4 guides and remove the No. 2 deck board.



9. REMOVE LUGGAGE COMPARTMENT TRIM BOX


    B194633
  1. Remove the 4 caps.



    B190116
  1. Remove the 4 bolts and luggage compartment trim box.



10. REMOVE ROPE HOOK ASSEMBLY


    B191405
  1. Remove the bolt and rope hook.

    HINT:
    Use the same procedure for both sides.



11. REMOVE NO. 1 DECK BOARD SUB-ASSEMBLY


    B190117
  1. Detach the 5 clips and remove the No. 1 deck board.



12. REMOVE DECK BOARD REINFORCEMENT SUB-ASSEMBLY


    B190120
  1. Remove the 4 bolts and deck board reinforcement.



13. REMOVE DECK BOARD BRACKET


    B190119
  1. Remove the 2 bolts and deck board bracket.



14. REMOVE SEAT TRACK BRACKET FRONT COVER OUTER


    B191196E02
  1. Detach the 2 claws and 2 guides in the order shown in the illustration, and then remove the seat track bracket front cover outer.



15. REMOVE SEAT TRACK BRACKET FRONT COVER INNER


    B232092E01
  1. Detach the claw, clip and 2 guides in the order shown in the illustration, and then remove the seat track bracket front cover inner.



16. REMOVE REAR NO. 2 SEAT ASSEMBLY RH (for Power Seat)


    B191200
  1. Remove the 2 bolts.



    B191203
  1. Remove the 2 bolts.

  1. Remove the connector.

  1. Remove the rear No. 2 seat assembly RH from the vehicle.

    NOTICE:
    Be careful not to damage the vehicle body.



17. REMOVE REAR NO. 2 SEAT ASSEMBLY RH (for Manual Seat)


    B191200
  1. Remove the 2 bolts.



    B191201
  1. Remove the 2 bolts.

  1. Remove the rear No. 2 seat assembly RH from the vehicle.

    NOTICE:
    Be careful not to damage the vehicle body.



18. REMOVE REAR SEAT CUSHION HINGE LOWER COVER RH


    B191794
  1. Detach the 2 clips and 5 claws, and remove the rear seat cushion hinge lower cover.



19. REMOVE REAR FLOOR STEP NO. 1 COVER


    B191403E01
  1. Using a screwdriver with its tip wrapped in protective tape, detach the 2 claws and remove the cap.

    HINT:
    Use the same procedure for both sides.



20. REMOVE REAR FLOOR STEP NO. 2 COVER


    B193052E01
  1. Using a screwdriver with its tip wrapped in protective tape, detach the 2 claws and remove the cap.

    HINT:
    Use the same procedure for both sides.



21. REMOVE REAR DOOR SCUFF PLATE RH


    B186665
  1. Remove the bolt.

  1. Detach the 5 clips, 6 claws and 2 guides, and remove the rear door scuff plate front side.



    B186666
  1. Remove the 2 bolts.

  1. Detach the 5 clips and 2 claws, and remove the scuff plate rear side.



22. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH


    B191804
  1. Remove the rear door opening weatherstrip.



23. REMOVE ROPE HOOK ASSEMBLY

HINT:
Use the same procedure for both sides.



    B190140E01
  1. Using a screwdriver with its tip wrapped in protective tape, detach the 2 claws and remove the cover.



    B190141
  1. Remove the bolt and the rope hook.



24. REMOVE REAR FLOOR MAT SUPPORT PLATE


    B190142
  1. Detach the 5 clips and 4 claws, and remove the rear floor mat support plate.



25. REMOVE QUARTER TRIM PANEL ASSEMBLY RH (for Standard)


    B190145
  1. Detach the 3 claws and remove the outer lap belt anchor cover.



    B190158
  1. Remove the bolt and outer lap belt anchor.



    B190146
  1. Remove the bolt and outer lap belt anchor.



    B190148E01
  1. Using a screwdriver with its tip wrapped in protective tape, detach the 2 claws and remove the cover.

  1. Remove the 2 bolts and 2 clips.

  1. Detach the 11 clips.



  1. Disconnect the connector and remove the quarter trim panel.


    B219907



26. REMOVE QUARTER TRIM PANEL ASSEMBLY RH (for Power Seat)


    B190145
  1. Detach the 3 claws and remove the outer lap belt anchor cover.



    B190158
  1. Remove the bolt and outer lap belt anchor.



    B190146
  1. Remove the bolt and outer lap belt anchor.



    B190148E01
  1. Using a screwdriver with its tip wrapped in protective tape, detach the 2 claws and remove the cover.

  1. Remove the 2 bolts and 2 clips.

  1. Detach the 11 clips.



  1. Disconnect the 3 connectors and remove the quarter trim panel.


    B222459



27. REMOVE REAR WINDOW SIDE GARNISH ASSEMBLY RH


    B190121E02
  1. Using a screwdriver with its tip wrapped in protective tape, detach the claw and remove the cover.



    B190124
  1. Remove the bolt.

  1. Detach the 5 clips.

  1. Pass the rear seat outer belt floor anchor through the rear window side garnish, and remove the rear window side garnish.



28. REMOVE REAR WINDOW NO. 2 SIDE GARNISH ASSEMBLY RH


    B190122E01
  1. Using a screwdriver with its tip wrapped in protective tape, detach the claw and remove the cover.



    B190123
  1. Remove the bolt.

  1. Detach the 5 clips.

  1. Pass the rear seat outer belt floor anchor through the rear window No. 2 side garnish, and remove the rear window No. 2 side garnish.



29. REMOVE REAR SIDE NO. 2 AIR DUCT


    E181294
  1. Remove the 2 clips and the air duct.



30. REMOVE QUARTER TRIM BRACKET RH


    I104301
  1. Detach the clamp.

  1. Remove the 2 bolts and the quarter trim bracket.



31. REMOVE COVER SUB-ASSEMBLY


    I104302
  1. Detach the 2 claws and remove the cover.



32. REMOVE REAR SIDE NO. 1 AIR DUCT


    I104303
  1. Detach the clamps.

  1. Remove the clip and the air duct.



33. SEPARATE AMPLIFIER ANTENNA ASSEMBLY


    I104304
  1. Remove the bolt and separate the amplifier antenna.



34. REMOVE FOLD SEAT CONTROL ECU


    B194058
  1. Disconnect the 2 connectors.

  1. Remove the 2 nuts and fold seat control ECU.



35. REMOVE REAR COOLING UNIT ASSEMBLY


E181295
  1. Detach the 3 clamps.

  1. Disconnect the 4 connectors.



    E181296
  1. Remove the 3 bolts, nut and the rear cooling unit.