Home › Engine / Hybrid System › 3UR-FE INTAKE / EXHAUST › EXHAUST PIPE

EXHAUST PIPE > REMOVAL

for Preparation Click here


CAUTION:
  1. Wear protective gloves when removing the exhaust pipe.
  2. The exhaust pipe is extremely hot immediately after the engine has stopped.
  3. Confirm that the exhaust pipe has cooled down before removing it.



1. REMOVE TAILPIPE ASSEMBLY


A204853
  1. Remove the bolt, clamp and gasket.

  1. Disconnect the tailpipe assembly from the 2 exhaust pipe supports.



2. REMOVE CENTER EXHAUST PIPE ASSEMBLY


A204852
  1. Remove the 4 bolts.

  1. Disconnect the center exhaust pipe assembly from the 4 exhaust pipe supports.

  1. Remove the center exhaust pipe assembly from the front exhaust pipe assembly and front No. 3 exhaust pipe sub-assembly.

  1. Remove the 2 gaskets from the front exhaust pipe assembly and front No. 3 exhaust pipe sub-assembly.



3. REMOVE CENTER ENGINE UNDER COVER (for 4WD)


    A230307
  1. Remove the 4 bolts and center engine under cover.



4. REMOVE TRANSFER AIR GUIDE (for 4WD)


    A230308
  1. Remove the 2 bolts and transfer air guide.



5. REMOVE PROPELLER SHAFT HEAT INSULATOR (for 4WD)


    C158452
  1. Remove the 2 bolts and heat insulator from the heat insulator bracket.



6. REMOVE HEATED OXYGEN SENSOR (for Bank 1 Sensor 2)


A184941E01
  1. Disconnect the heated oxygen sensor connector.

  1. Using SST, remove the heated oxygen sensor.

    SST
    09224-00010  



7. REMOVE HEATED OXYGEN SENSOR (for Bank 2 Sensor 2)


A184939E01
  1. Disconnect the heated oxygen sensor connector and 2 clamps..

  1. Using SST, remove the heated oxygen sensor.

    SST
    09224-00010  



8. REMOVE FRONT NO. 2 EXHAUST PIPE ASSEMBLY


A184927
  1. Remove the 2 bolts and 2 nuts.

  1. Disconnect the front No. 3 exhaust pipe sub-assembly from the exhaust pipe support.

  1. Remove the front No. 3 exhaust pipe sub-assembly from the front No. 2 exhaust pipe sub-assembly.

  1. Disconnect the air fuel ratio sensor connector.



    A184928
  1. Remove the 3 nuts, front No. 2 exhaust pipe sub-assembly and 2 gaskets from the exhaust manifold LH.



9. REMOVE FRONT EXHAUST PIPE ASSEMBLY
  1. Disconnect the air fuel ratio sensor connector.



    A184929
  1. Remove the 3 nuts, front exhaust pipe and gasket from the exhaust manifold RH.



10. REMOVE AIR FUEL RATIO SENSOR (for Bank 1 Sensor 1)


    A194684E01
  1. Using SST, remove the air fuel ratio sensor.

    SST
    09224-00010  



11. REMOVE AIR FUEL RATIO SENSOR (for Bank 2 Sensor 1)


    A194684E01
  1. Using SST, remove the air fuel ratio sensor.

    SST
    09224-00010  



12. REMOVE MONOLITHIC CONVERTER PROTECTOR (for Bank 1)


    A230513
  1. Remove the 4 bolts and 4 nuts.

  1. Remove the 2 monolithic converter protectors.

  1. Remove the 2 LH converter protector stays and 2 No. 2 converter protector stays.



13. REMOVE NO. 1 MONOLITHIC CONVERTER PROTECTOR (for Bank 1)


    A230514
  1. Remove the 4 bolts and 4 nuts.

  1. Remove the 2 No. 1 monolithic converter protectors.

  1. Remove the 2 No. 2 converter protector stays and 2 No. 3 converter protector stays.



14. REMOVE MONOLITHIC CONVERTER PROTECTOR (for Bank 2)


    A230515
  1. Remove the 4 bolts and 4 nuts.

  1. Remove the 2 monolithic converter protectors.

  1. Remove the 2 LH converter protector stays and 2 No. 2 converter protector stays.



15. REMOVE NO. 1 MONOLITHIC CONVERTER PROTECTOR (for Bank 2)


    A230516
  1. Remove the 4 bolts and 4 nuts.

  1. Remove the 2 No. 1 monolithic converter protectors.

  1. Remove the 2 No. 2 converter protector stays and 2 No. 3 converter protector stays.