Home › Drivetrain ยท DRIVE SHAFT / PROPELLER SHAFT › PROPELLER SHAFT ASSEMBLY (for 4WD)

PROPELLER SHAFT ASSEMBLY (for 4WD) > REASSEMBLY

for Preparation Click here



1. INSTALL REAR PROPELLER SHAFT UNIVERSAL JOINT SPIDER

HINT:
Use the same installation procedure for both the front and rear propeller shaft universal joint spiders.



    C134387
  1. Apply MP grease to a new universal joint spider and universal joint spider bearings.

    NOTICE:
    Be careful not to apply too much grease.



    C160084E01
  1. Measure dimension A between the snap ring grooves.

  1. Install the universal joint spider bearing into the universal joint spider and measure dimension B.

    HINT:
    When measuring dimension B, clamp the universal joint spider and universal joint spider bearing in a vise to hold them together.



  1. Select hole snap rings of the correct thickness to make dimensions A and B the same.



      G038874
    1. w/o Grease Fitting Spider Bearing:

      Hole Snap Ring Thickness:
      Color
      Thickness
      Purple
      1.46 mm (0.0574 in.)
      Black
      1.49 mm (0.0586 in.)
      Copper
      1.51 mm (0.0594 in.)
      Black
      1.52 mm (0.0598 in.)
      Black
      1.54 mm (0.0606 in.)
      White
      1.56 mm (0.0614 in.)
      Black
      1.57 mm (0.0618 in.)
      Yellow
      1.59 mm (0.0625 in.)
      Black
      1.62 mm (0.0638 in.)
      Blue
      1.64 mm (0.0646 in.)

      NOTICE:
      1. Use new hole snap rings.
      2. If possible, use hole snap rings of the same thickness for both edges.



    2. C166540
    3. w/ Grease Fitting Spider Bearing:

      Hole Snap Ring Thickness:
      Color
      Thickness
      Black
      1.49 mm (0.0586 in.)
      Copper
      1.51 mm (0.0594 in.)
      White
      1.56 mm (0.0614 in.)
      Yellow
      1.59 mm (0.0625 in.)

      NOTICE:
      1. Use new hole snap rings.
      2. If possible, use hole snap rings of the same thickness for both edges.

  1. Temporarily install the universal joint spider and 2 universal joint spider bearings into the universal joint flange yoke.



    C179273E01
  1. Using SST, press the universal joint spider bearing into the universal joint flange yoke until the groove can be seen.

    SST
    09950-40011   (09951-04020, 09952-04010, 09953-04020, 09954-04020, 09955-04051, 09957-04010)
    09950-60010   (09951-00290)
    09336-16010  

    NOTICE:
    Confirm that the universal joint spider moves smoothly while pressing it in.



    C179275E01
  1. Using needle-nose pliers, install a hole snap ring into the groove on the universal joint flange yoke.

    HINT:
    Use the same installation procedure for the universal joint spider bearing on the opposite side.

  1. Temporarily install the universal joint spider and 2 universal joint spider bearings into the propeller shaft's universal joint flange yoke.



    C179276E01
  1. Using SST, press the universal joint spider bearing into the universal joint flange yoke until the groove can be seen.

    SST
    09950-40011   (09951-04020, 09952-04010, 09953-04020, 09954-04020, 09955-04051, 09957-04010)
    09950-60010   (09951-00290)
    09336-16010  

    NOTICE:
    1. Position SST (09336-16010) so that the cutout faces the propeller shaft tube.
    2. Confirm that the universal joint spider moves smoothly while pressing it in.



    C179263E01
  1. Using needle-nose pliers, install a hole snap ring into the groove on the universal joint yoke.

    HINT:
    Use the same installation procedure for the universal joint spider bearing on the opposite side.



2. INSPECT PROPELLER SHAFT GREASE FITTING DIRECTION


HINT:
When replacing a spider bearing, be sure that the grease fitting hole is facing the direction shown in the illustration.



C158514E02



3. INSPECT UNIVERSAL JOINT SPIDER BEARING


    C158513
  1. Inspect the spider bearing for wear or damage.

  1. Using a dial indicator, measure the spider bearing axial play by turning the yoke of the flange while holding the shaft tightly.

    Maximum runout:
    0.05 mm (0.00197 in.)

    1. If the spider bearing axial play exceeds the maximum, replace the spider bearing.