Home › Drivetrain ยท JF3A TRANSFER / 4WD / AWD › TRANSFER ASSEMBLY

TRANSFER ASSEMBLY > DISASSEMBLY

for Preparation Click here



1. REMOVE HEAT INSULATOR BRACKET


    C180866
  1. Remove the heat insulator bracket.



2. REMOVE TRANSFER CASE PLUG


    C180854
  1. Using a 10 mm hexagon wrench, remove the case plug, compression spring, ball and relief valve seat.



3. REMOVE TRANSFER OIL PUMP PLATE


    C180849
  1. Remove the 4 bolts and oil pump plate.

    NOTICE:
    Do not drop the oil pump drive rotor and oil pump driven rotor.



    C180851E01
  1. Remove the oil seal ring from the input shaft.



    C180850E01
  1. Remove the drive rotors.



    C180856
  1. Remove the O-ring from the transfer oil pump plate.



4. REMOVE TRANSFER CASE STRAIGHT PIN


    C180853E01
  1. Remove the 2 straight pins.

    NOTICE:
    Do not drop the straight pins.



5. REMOVE TRANSFER OIL PUMP PLATE OIL SEAL


    C180855
  1. Using a screwdriver and hammer, tap out the oil seal from the oil pump plate.

    NOTICE:
    Be careful not to damage the oil seal and oil pump plate contact surfaces.



6. REMOVE FRONT OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY


    C180857E01
  1. Using SST and hammer, loosen the staked part of the lock nut.

    SST
    09930-00010  



    C180858E01
  1. Using SST to hold the companion flange.

    SST
    09330-00021  

  1. Using a socket wrench (32mm), remove the lock nut.



    C180859
  1. Remove the O-ring.



    C180860
  1. Remove the front output shaft companion flange sub-assembly.



7. REMOVE TRANSFER CASE FRONT OIL SEAL


    C180928E01
  1. Using SST, remove the oil seal from the front case.

    NOTICE:
    Be careful not to damage the front case contact surfaces.



8. REMOVE REAR OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY


    C180861E01
  1. Using SST and hammer, loosen the staked part of the lock nut.

    SST
    09930-00010  



    C180862E01
  1. Using SST to hold the companion flange.

    SST
    09330-00021  

  1. Using a socket wrench (32mm), remove the lock nut.



    C180863
  1. Remove the O-ring.



    C180864
  1. Remove the rear output shaft companion flange sub-assembly.



9. REMOVE TRANSFER CASE REAR OIL SEAL


    C180929E01
    C180930
  1. Using a screwdriver and hammer, tap out the oil seal from the rear case.

    NOTICE:
    Be careful not to damage the rear case contact surfaces.

    Remove the 2 output washers.



10. REMOVE NO. 1 TRANSFER CASE PLUG


    C180865
  1. Remove the No. 1 transfer case plug, compression spring and pin.



11. REMOVE TRANSFER CASE PLUG


    C180867
  1. Using a 6 mm hexagon wrench, remove the case plug.



12. REMOVE REAR TRANSFER CASE


    C180868
  1. Remove the 14 bolts.

  1. Remove the rear case.

    HINT:
    If necessary, tap the rear case with a plastic-faced hammer to remove it.



13. REMOVE TRANSFER OUTPUT SHAFT FRONT NEEDLE ROLLER BEARING


    C180873
  1. Remove the transfer output shaft front needle roller bearing from the output shaft.



    C180874
  1. Remove the output shaft spacer from the output shaft.



14. REMOVE NO. 1 SYNCHRONIZER RING


    C180875
  1. w/ No. 1 Synchronizer Ring:
    Remove the No. 1 synchronizer ring from center differential case.



15. REMOVE TRANSFER SHIFT ACTUATOR ASSEMBLY


    C180869
  1. Using 2 screwdrivers and a hammer, tap out the 3 shift fork shaft snap rings.



    C180870
  1. Remove the 2 bolts.



    C180872
  1. Remove the 3 bolts. Then remove the shift actuator, No.1 gear shift fork and No.2 gear shift fork from the rear case.



    C160356
  1. Remove the o-ring from the transfer shift actuator assembly.



    C180876
  1. w/ No. 1 Synchronizer Ring:
    Remove the washer from the rear case.



16. REMOVE TRANSFER HIGH & LOW CLUTCH SLEEVE


    C180881
  1. Remove the transfer high and low clutch sleeve from the output shaft.



17. REMOVE REAR OUTPUT SHAFT


    C180878
  1. Using a snap ring expander, remove the snap ring.



    C180879
  1. Using a plastic-faced hammer, carefully tap the case rear, and remove the output shaft together with the drive chain and driven sprocket.

  1. Remove the output shaft and driven sprocket from the drive chain.



    C180880
  1. Using a snap ring expander, remove the snap ring from the rear transfer case.



18. REMOVE SIDE GEAR SHAFT HOLDER BEARING (for Roller Bearing)


    C180882
  1. Using a screwdriver, remove the snap ring.



    C180883E01
  1. Using SST, remove the side gear shaft holder bearing.

    SST
    09308-00010  



19. REMOVE SIDE GEAR SHAFT HOLDER BEARING (for Ball Bearing)


    C273275E01
  1. Using SST and a press, remove the side gear shaft holder bearing.

    SST
    09950-00020  
    09950-60010   (09951-00380)
    09950-70010   (09951-07150)

    NOTICE:
    Be careful not to drop or damage the driven sprocket.



20. REMOVE TRANSFER OIL SEPARATOR SUB-ASSEMBLY


    C180884
  1. Remove the 3 bolts and oil separator.



    C180885
  1. Remove the O-ring from the oil separator.



21. REMOVE TRANSFER CASE MAGNET


    C180886
  1. Remove the transfer case magnet.



22. REMOVE INPUT SHAFT ASSEMBLY


    C180887
  1. Using a 14 mm hexagon wrench, remove the 2 case plugs from the front case.



    C180888
  1. Remove the snap ring. Then remove the input shaft from the front case.



23. REMOVE TRANSFER LOW PLANETARY RING GEAR


    C180892
  1. Remove the low planetary ring gear from the front case.



    C180891
  1. Using a screw driver, remove the snap ring from the front transfer case.



24. REMOVE TRANSFER DRIVEN SPROCKET BEARING (for Roller Bearing)


    C180890
  1. Using a screwdriver, remove the snap ring.



    C180893E01
  1. Using SST, remove the driven sprocket bearing from the front case.

    SST
    09950-60020   (09951-00680)
    09950-70010   (09951-07150)



25. REMOVE TRANSFER DRIVEN SPROCKET BEARING (for Ball Bearing)


    C180893E01
  1. Using SST, remove the driven sprocket bearing from the front case.

    SST
    09950-60020   (09951-00680)
    09950-70010   (09951-07150)



26. REMOVE NO. 1 TRANSFER INPUT SHAFT SEAL RING


    C162486E01
  1. Remove the oil seal ring from the input shaft.



27. REMOVE TRANSFER INPUT SHAFT BEARING


    C159629
  1. Using a snap ring expander, remove the snap ring.



    C180896E01
  1. Using SST and a press, pull out the bearing.

    SST
    09555-55010  
    09950-00030  
    09950-60010   (09951-00480)

    NOTICE:
    Be careful not to drop or damage the low planetary gear.



28. REMOVE TRANSFER INPUT SHAFT BIMETAL FORMED BUSH


    C173631E01
  1. Using SST, remove the bush.

    SST
    09387-00041   (09387-01021, 09387-01030, 09387-01040)



29. REMOVE TRANSFER INPUT SHAFT PLUG


    C173494E01
  1. Using SST and a hammer, tap out the input shaft plug.

    SST
    09950-70010   (09951-07150)
    09950-60010   (09951-00350)



30. REMOVE NO. 1 TRANSFER OUTPUT SHAFT SPACER


    C180899
  1. Using 2 screwdrivers, tap out the snap ring.



    C180900
  1. Remove the output shaft spacer from the output shaft.



    C173604
  1. Remove the seal ring from the output shaft spacer.



31. REMOVE CENTER DIFFERENTIAL CASE


    C180902E01
  1. Remove the straight pin from the output shaft.

  1. Remove the center differential case from the output shaft.



    C173607
  1. w/ No. 1 Synchronizer Ring:
    Using a snap ring expander, remove the snap ring.



    C173608
  1. w/ No. 1 Synchronizer Ring:
    Remove the synchromesh shifting key spring and No. 2 synchromesh shifting keys from the center differential case.



32. REMOVE FRONT DRIVE CLUTCH SLEEVE


    C180906E01
  1. Remove the front driver clutch sleeve with synchromesh from the output shaft.



    C180903E01
  1. Remove the 2 transfer clutch hub bearings from shaft.



    C180927
  1. Remove the synchronizer ring set from the drive clutch sleeve.



    C180907E01
  1. Using a screw driver, remove the 2 shifting key snap rings and 3 shifting keys from the driver clutch sleeve.



    C180908
  1. Remove the transfer clutch hub from the drive clutch sleeve.



33. REMOVE REAR TRANSFER OUTPUT SHAFT


    C180909E01
  1. Using SST and a press, press out the bearing.

    SST
    09527-10011  

    NOTICE:
    Be careful not to drop or damage the output shaft.



    C180910
  1. Remove the transfer drive sprocket sub-assembly from the output shaft.



    C180911
  1. Remove the needle roller bearing from the output shaft.