Home › Drivetrain ยท JF3A TRANSFER / 4WD / AWD › TRANSFER ASSEMBLY

TRANSFER ASSEMBLY > DISASSEMBLY

for Preparation Click here



1. REMOVE HEAT INSULATOR BRACKET


    C180866
  1. Remove the bolt and heat insulator bracket.



2. REMOVE TRANSFER CASE PLUG


    C180854E01
  1. Using a 10 mm hexagon wrench, remove the transfer case plug, compression spring, ball and relief valve seat.
    Text in Illustration 
    *1
    Transfer Case Plug
    *2
    Compression Spring
    *3
    Ball
    *4
    Relief Valve Seat



3. REMOVE TRANSFER OIL PUMP PLATE


    C180849
  1. Remove the 4 bolts and transfer oil pump plate.

    NOTICE:
    Do not drop the transfer oil pump drive rotor and transfer oil pump driven rotor.



    C180851
  1. Remove the transfer oil seal ring from the transfer input shaft.



    C180850E02
  1. Remove the transfer oil pump drive rotor and transfer oil pump driven rotor.
    Text in Illustration 
    *1
    Transfer Oil Pump Drive Rotor
    *2
    Transfer Oil Pump Driven Rotor



    C180856
  1. Remove the O-ring from the transfer oil pump plate.



4. REMOVE TRANSFER CASE STRAIGHT PIN


    C180853E02
  1. Remove the 2 transfer case straight pins.

    NOTICE:
    Do not drop the transfer case straight pin.



5. REMOVE TRANSFER OIL PUMP PLATE OIL SEAL


    C180855E01
  1. Using a screwdriver and hammer, tap out the transfer oil pump plate oil seal from the transfer oil pump plate.
    Text in Illustration 
    *1
    Protective Tape

    NOTICE:
    Be careful not to damage the transfer oil pump plate contact surfaces.



6. REMOVE FRONT OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY


    C180857E02
  1. Using SST and a hammer, loosen the staked part of the transfer output shaft nut.

    SST
    09930-00010  

    NOTICE:
    1. Be sure to use SST with the tapered surface facing the shaft.
    2. Do not grind the tip of SST with a grinder or other device.
    3. Completely loosen the staked part of the transfer output shaft nut when removing it.
    4. Do not damage the threads of the driven sprocket.



    C270532E01
  1. Use SST to hold the front output shaft companion flange sub-assembly.

    SST
    09330-00021  
    Text in Illustration 
    *a
    Hold
    *b
    Turn

  1. Using a 32 mm socket wrench, remove the transfer output shaft nut.



    C180859
  1. Remove the O-ring.



    C180860
  1. Remove the front output shaft companion flange sub-assembly.



7. REMOVE TRANSFER CASE FRONT OIL SEAL


    C180928E02
  1. Using SST, remove the transfer case front oil seal from the front transfer case.

    SST
    09308-00010  

    NOTICE:
    Be careful not to damage the front transfer case contact surfaces.



8. REMOVE REAR OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY


    C180861E02
  1. Using SST and a hammer, loosen the staked part of the transfer output shaft nut.

    SST
    09930-00010  

    NOTICE:
    1. Be sure to use SST with the tapered surface facing the shaft.
    2. Do not grind the tip of SST with a grinder or other device.
    3. Completely loosen the staked part of the transfer output shaft nut when removing it.
    4. Do not damage the threads of the rear transfer output shaft.



    C270533E01
  1. Use SST to hold the rear output shaft companion flange sub-assembly.

    SST
    09330-00021  
    Text in Illustration 
    *a
    Hold
    *b
    Turn

  1. Using a 32 mm socket wrench, remove the transfer output shaft nut.



    C180863
  1. Remove the O-ring.



    C180864
  1. Remove the rear output shaft companion flange sub-assembly.



9. REMOVE TRANSFER CASE REAR OIL SEAL


    C180929E02
  1. Using SST, remove the transfer case rear oil seal from the rear transfer case.

    SST
    09308-00010  

    NOTICE:
    Be careful not to damage the rear transfer case contact surfaces.



    C180930
  1. Remove the 2 output washers.



10. REMOVE NO. 1 TRANSFER CASE PLUG


    C180865E01
  1. Remove the No. 1 transfer case plug, compression spring and pin.
    Text in Illustration 
    *1
    No. 1 Transfer Case Plug
    *2
    Compression Spring
    *3
    Pin



11. REMOVE TRANSFER CASE PLUG


    C180867
  1. Using a 6 mm hexagon wrench, remove the transfer case plug.



12. REMOVE REAR TRANSFER CASE


    C180868
  1. Remove the 14 bolts.

  1. Remove the rear transfer case.

    HINT:
    If necessary, tap the rear transfer case with a plastic-faced hammer to remove it.



13. REMOVE TRANSFER OUTPUT SHAFT FRONT NEEDLE ROLLER BEARING


    C270566
  1. Remove the transfer output shaft front needle roller bearing from the rear output shaft assembly.



    C270567
  1. Remove the spacer from the rear output shaft assembly.



14. REMOVE TRANSFER SHIFT ACTUATOR ASSEMBLY


    C180869
  1. Using 2 screwdrivers and a hammer, tap out the 3 transfer gear shift fork shaft snap rings.



    C180870
  1. Remove the 2 bolts.



    C180872
  1. Remove the 3 bolts. Then remove the transfer shift actuator assembly, No. 1 transfer gear shift fork and No. 2 transfer gear shift fork from the rear output shaft assembly.



    C160356
  1. Remove the O-ring from the transfer shift actuator assembly.



15. REMOVE TRANSFER HIGH AND LOW CLUTCH SLEEVE


    C270568
  1. Remove the transfer high and low clutch sleeve from the rear output shaft assembly.



16. REMOVE REAR OUTPUT SHAFT ASSEMBLY


    C270569
  1. Using a snap ring expander, expand the rear transfer output shaft snap ring.



    C270570
  1. Using a plastic-faced hammer, carefully tap the case rear, and remove the rear output shaft assembly together with the drive chain and driven sprocket.

  1. Remove the rear output shaft assembly and driven sprocket from the drive chain.



    C180880
  1. Using a snap ring expander, remove the rear transfer output shaft snap ring from the rear transfer case.



17. REMOVE SIDE GEAR SHAFT HOLDER BEARING


    C273275E01
  1. Using SST and a press, remove the side gear shaft holder bearing.

    SST
    09950-00020  
    09950-60010   (09951-00380)
    09950-70010   (09951-07150)



18. REMOVE TRANSFER OIL SEPARATOR SUB-ASSEMBLY


    C180884
  1. Remove the 3 bolts and transfer oil separator sub-assembly.



    C180885
  1. Remove the O-ring from the transfer oil separator sub-assembly.



19. REMOVE TRANSFER CASE MAGNET


    C180886
  1. Remove the transfer case magnet.



20. REMOVE INPUT SHAFT ASSEMBLY


    C180887
  1. Using a 14 mm hexagon wrench, remove the 2 transfer case plugs from the front transfer case.



    C180888
  1. Expand the transfer input shaft hole snap ring. Then remove the input shaft assembly from the front transfer case.



21. REMOVE TRANSFER LOW PLANETARY RING GEAR
  1. Using a snap ring expander, remove the transfer low planetary ring gear hole snap ring.



    C180892
  1. Remove the transfer low planetary ring gear from the front transfer case.



    C180891
  1. Using a screwdriver, remove the transfer input shaft hole snap ring from the front transfer case.



22. REMOVE TRANSFER DRIVEN SPROCKET BEARING


    C180893E01
  1. Using SST, remove the transfer driven sprocket bearing from the front transfer case.

    SST
    09950-60020   (09951-00680)
    09950-70010   (09951-07150)



23. REMOVE NO. 1 TRANSFER INPUT SHAFT SEAL RING


    C162486
  1. Remove the No. 1 transfer input shaft seal ring from the transfer input shaft.



24. REMOVE TRANSFER INPUT SHAFT BEARING


    C159629
  1. Using a snap ring expander, remove the transfer input shaft snap ring.



    C270535E01
  1. Using SST and a press, pull out the transfer input shaft bearing.

    SST
    09555-55010  
    09950-00030  
    09950-60010   (09951-00480)
    Text in Illustration 
    *a
    Hold
    *b
    Turn

    NOTICE:
    Be careful not to drop or damage the transfer low planetary gear assembly.

  1. Remove the transfer low planetary gear assembly and 2 transfer low planetary gear bearings from the transfer input shaft.



25. REMOVE TRANSFER INPUT SHAFT BIMETAL FORMED BUSH


    C173631E01
  1. Using SST, remove the transfer input shaft bimetal formed bush.

    SST
    09387-00041   (09387-01021, 09387-01030, 09387-01041)



26. REMOVE TRANSFER INPUT SHAFT PLUG


    C173494E01
  1. Using SST and a hammer, tap out the transfer input shaft plug.

    SST
    09950-70010   (09951-07150)
    09950-60010   (09951-00350)



27. REMOVE NO. 1 TRANSFER OUTPUT SHAFT SPACER


    C270536
  1. Using 2 screwdrivers, tap out the snap ring.



    C270537
  1. Remove the No. 1 transfer output shaft spacer from the rear transfer output shaft.



    C173604E01
  1. Remove the seal ring from the No. 1 transfer output shaft spacer.
    Text in Illustration 
    *1
    Seal Ring
    *2
    No. 1 Transfer Output Shaft Spacer



28. REMOVE CENTER DIFFERENTIAL CASE


    C270538
  1. Remove the straight pin from the rear transfer output shaft.

  1. Remove the center differential case from the rear transfer output shaft.



29. REMOVE FRONT DRIVE CLUTCH SLEEVE


    C180906E01
  1. Remove the front drive clutch sleeve with the transfer synchronizer ring set, 2 shifting key snap rings, 3 shifting keys and transfer clutch hub from the rear transfer output shaft.



    C180903E01
  1. Remove the 2 transfer clutch hub bearings from the rear transfer output shaft.



    C180927E01
  1. Remove the transfer synchronizer ring set from the front drive clutch sleeve.
    Text in Illustration 
    *1
    Transfer Synchronizer Ring Set



    C180907E02
  1. Using a screwdriver, remove the 2 shifting key snap rings and 3 shifting keys from the front drive clutch sleeve.
    Text in Illustration 
    *1
    Shifting Key Snap Ring
    *2
    Shifting Key



    C180908
  1. Remove the transfer clutch hub from the front drive clutch sleeve.



30. REMOVE REAR TRANSFER OUTPUT SHAFT


    C270571E01
  1. Using SST and a press, press out the bearing.

    SST
    09950-00020  

    NOTICE:
    Be careful not to drop or damage the rear transfer output shaft.



    C180910
  1. Remove the transfer drive sprocket sub-assembly from the rear transfer output shaft.



    C180911
  1. Remove the needle roller bearing from the rear transfer output shaft.