Home › Drivetrain ยท JF3A TRANSFER / 4WD / AWD › TRANSFER ASSEMBLY

TRANSFER ASSEMBLY > REASSEMBLY

for Preparation Click here


HINT:
Coat all of the sliding and rotating surfaces with gear oil before reassembly.



1. INSTALL REAR TRANSFER OUTPUT SHAFT


    C180911
  1. Install a new needle roller bearing.



    C180910
  1. Install the transfer drive sprocket sub-assembly.



    C180919E01
  1. Using SST and press, press in a new bearing.

    SST
    09308-14010  
    09316-20011  

    NOTICE:
    Make sure the bearing is installed in the correct direction.



2. INSTALL FRONT DRIVE CLUTCH SLEEVE


    C180908
  1. Install the transfer clutch hub onto the front drive clutch sleeve.



    C180907
  1. Install the 3 shifting keys and 2 shifting key snap rings

    NOTICE:
    Install the key springs so that their end gaps are not in line.



    C180927
  1. Install the synchronizer ring set.

    NOTICE:
    Align the slots of the synchronizer outer with the inner rings.



    C180903E01
  1. Install the 2 transfer clutch hub bearings.



    C180920
  1. Install the front drive clutch sleeve with synchromesh onto the output shaft.

    NOTICE:
    Align the cutouts in the front drive sprocket with the protrusions on the center synchronizer ring.



3. INSTALL CENTER DIFFERENTIAL CASE


    C173620E01
  1. w/ No. 1 Synchronizer Ring:
    Install the synchromesh shifting key spring and No. 2 synchromesh shifting keys as shown in the illustration.



    C173607
  1. w/ No. 1 Synchronizer Ring:
    Using a snap ring expander, install the snap ring.



    C180902E01
  1. Install the center differential case to the output shaft.

  1. Install the straight pin to the output shaft.



4. INSTALL NO. 1 TRANSFER OUTPUT SHAFT SPACER


    C173604
  1. Install a new seal ring to the output shaft spacer.



    C173622
  1. Align the pin with the straight pin groove of the output shaft spacer, and slide on the output shaft spacer.



    C173624
  1. Using a screwdriver and hammer, tap on the snap ring.



5. INSTALL TRANSFER INPUT SHAFT PLUG


    C180921E01
  1. Using SST and a hammer, tap in a new input shaft plug until its surface is 1.0 to 1.8 mm (0.0394 to 0.0709 in.) from the input shaft upper surface.

    SST
    09950-70010   (09951-07150)
    09950-60010   (09951-00380)

    NOTICE:
    Be careful not to damage or deform the input shaft plug when tapping it.



6. INSTALL TRANSFER INPUT SHAFT BIMETAL FORMED BUSH


    C173632E01
  1. Using SST and a hammer, tap in a new bush until its surface is 5.5 to 5.9 mm (0.217 to 0.232 in.) from the input shaft upper surface.

    SST
    09950-70010   (09951-07150)
    09950-60010   (09951-00610)

    NOTICE:
    Be careful not to damage the input shaft.



7. INSTALL TRANSFER INPUT SHAFT BEARING


    C173499E01
  1. Install the low planetary gear bearing and low planetary gear to the input shaft.

    NOTICE:
    1. Make sure that the low planetary gear bearing is installed in the correct direction.
    2. Install the low planetary gear bearing so that its temper color side faces the low planetary gear.



    C173498E01
  1. Install the low planetary gear bearing and a new input shaft bearing to the input shaft.

    NOTICE:
    1. Make sure that the input shaft bearing is installed in the correct direction.
    2. Make sure that the low planetary gear bearing is installed in the correct direction.
    3. Install the low planetary gear bearing so that its temper color side faces the low planetary gear.



    C180922E01
  1. Using SST and a press, press in a new bearing.

    SST
    09513-36040  
    09527-17011  

    NOTICE:
    After press-fitting the bearing to the input shaft, check that the bearing moves smoothly.



    C160525E01
  1. Select a snap ring that allows for minimum axial play and install it to the shaft.

    Snap Ring Thickness:
    Mark
    Thickness
    C
    2.13 to 2.18 mm (0.0839 to 0.0858 in.)
    D
    2.18 to 2.23 mm (0.0858 to 0.0878 in.)
    E
    2.23 to 2.28 mm (0.0878 to 0.0898 in.)
    F
    2.28 to 2.33 mm (0.0898 to 0.0917 in.)
    G
    2.33 to 2.38 mm (0.0918 to 0.0937 in.)
    H
    2.38 to 2.43 mm (0.0937 to 0.0957 in.)
    J
    2.43 to 2.48 mm (0.0957 to 0.0976 in.)

  1. Using a snap ring expander, install the snap ring.

    NOTICE:
    Make sure that the snap ring is firmly installed to the groove.



8. INSTALL NO. 1 TRANSFER INPUT SHAFT SEAL RING


    C162486E01
  1. Apply transfer oil to a new seal ring.

  1. Install a new seal ring to the input shaft.



9. INSTALL TRANSFER DRIVEN SPROCKET BEARING (for Roller Bearing)


    C180923E01
  1. Install a new transfer driven sprocket bearing to the front transfer case in the direction shown in the illustration.

    SST
    09950-60020   (09951-00790)
    09950-70010   (09951-07150)

    NOTICE:
    Make sure that the transfer driven sprocket bearing is installed in the correct direction.



    C180890
  1. Using a screwdriver, install the snap ring.



10. INSTALL TRANSFER DRIVEN SPROCKET BEARING (for Ball Bearing)


    C180923E01
  1. Install a new transfer driven sprocket bearing to the front transfer case in the direction shown in the illustration.

    SST
    09950-60020   (09951-00790)
    09950-70010   (09951-07150)

    NOTICE:
    Make sure that the transfer driven sprocket bearing is installed in the correct direction.



11. INSTALL TRANSFER LOW PLANETARY RING GEAR


    C180891
  1. Install the snap ring to the front case.



    F043457E01
  1. Install the ring gear to the transfer front case.

    NOTICE:
    Make sure to install the ring gear in the correct direction.



    C173488
  1. Using a screwdriver install the snap ring.

    NOTICE:
    Make sure that the snap ring is firmly installed to the groove.



12. INSTALL INPUT SHAFT ASSEMBLY


    C180888
  1. While expanding the snap ring, install the input shaft to the front case.

  1. Apply adhesive to the threads of the 2 plugs.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

    NOTICE:
    Install the plugs within 3 minutes of application.



    C180887
  1. Using a 14 mm hexagon wrench, install the 2 plugs.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }



13. INSTALL TRANSFER CASE MAGNET


    C180886
  1. Install the transfer case magnet.



14. INSTALL TRANSFER OIL SEPARATOR SUB-ASSEMBLY


    C180885E01
  1. Install a new O-ring.



    C180884
  1. Install the oil separator with the 3 bolts.

    Torque:
    18 N*m{ 178 kgf*cm , 13 ft.*lbf }



15. INSTALL SIDE GEAR SHAFT HOLDER BEARING (for Roller Bearing)


    C180924E02
  1. Using SST and hammer, install a new side gear shaft holder bearing.

    SST
    09950-60010   (09951-00590)
    09950-70010   (09951-07150)



    C180882
  1. Using a screwdriver, install the snap ring.



16. INSTALL SIDE GEAR SHAFT HOLDER BEARING (for Ball Bearing)


    C273276E01
  1. Using SST and a press, install a new side gear shaft holder bearing.

    SST
    09214-60010  

    NOTICE:
    Press in the side gear shaft holder bearing until they fit to the edge.



17. INSTALL REAR OUTPUT SHAFT
  1. Install the snap ring to the rear case.

  1. Mount the rear case in a vise.

    NOTICE:
    Place aluminum plates on the vise to prevent damage to the rear case.



    C181033
  1. Install the rear output shaft , front drive chain and driven sprocket.

    NOTICE:
    Do not drop the clutch sleeve or shifting key.



    C180878
  1. Using a snap ring expander, install the snap ring to the out put shaft.

    NOTICE:
    Make sure that the snap ring is firmly installed to the groove.



18. INSTALL TRANSFER HIGH & LOW CLUTCH SLEEVE


    C180881
  1. Install the transfer high and low clutch sleeve to the output shaft.



19. INSTALL TRANSFER SHIFT ACTUATOR ASSEMBLY


    C180876
  1. w/ No. 1 Synchronizer Ring:
    Install the washer to the rear case.



    C160356E03
  1. Install a new O-ring to the shift actuator.



    C180872
  1. Set the No. 1 gear shift fork and No. 2 gear shift fork to the rear case. Then install the shift actuator to the rear case with the 3 bolts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }



    C180870
  1. Install the 2 bolts.

    Torque:
    24 N*m{ 245 kgf*cm , 18 ft.*lbf }



    C180869
  1. Using a screwdriver and hammer, tap the 3 shift fork shaft snap rings into the shift fork shaft.



20. INSTALL NO. 1 SYNCHRONIZER RING


    C180875
  1. w/ No. 1 Synchronizer Ring:
    Align the protrusion of the synchronizer ring with the notch on the differential case and install it.



21. INSTALL TRANSFER OUTPUT SHAFT FRONT NEEDLE ROLLER BEARING


    C180874
  1. Install the output shaft spacer.



    C180873
  1. Install the transfer output shaft front needle roller bearing.



22. INSTALL REAR TRANSFER CASE


    C160517E01
  1. Apply seal packing to the rear case as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent

    NOTICE:
    If the removed rear case will be reused: After removing the rear case, perform the following before reinstalling it: 1) using a knife, cut off any old FIPG on the rear case's contact surface, 2) clean off any remaining old FIPG from the rear case's contact surface, and 3) reapply seal packing to the rear case.



    C180868
  1. Install the rear case with the 14 bolts.

    Torque:
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }

    NOTICE:
    Tighten the bolts of the rear case within 10 minutes of applying the seal packing. The seal packing will dry very quickly.



23. INSTALL TRANSFER CASE PLUG
  1. Apply adhesive to the threads of the plug.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

    NOTICE:
    Install the plug within 3 minutes of application.



    C180867
  1. Using a 6 mm hexagon wrench, install the plug.

    Torque:
    39 N*m{ 400 kgf*cm , 29 ft.*lbf }



24. INSTALL NO. 1 TRANSFER CASE PLUG


    C180865
  1. Install the pin and compression spring to the front case.

  1. Apply adhesive to the threads of the plug.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

    NOTICE:
    Install the plug within 3 minutes of application.

  1. Install the plug.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }



25. INSTALL TRANSFER CASE FRONT OIL SEAL
  1. Apply transfer oil to the spline area of the output shaft.



    C159301E01
  1. Using SST and a hammer, tap in the oil seal until its surface is 1 to 1.5 mm (0.0394 to 0.0591 in.) from the case upper surface.

    SST
    09316-60011   (09316-00011)



26. INSTALL FRONT OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY
  1. Install the companion flange sub-assembly onto the drive sprocket sub-assembly.



    C181034E01
  1. Using SST to hold the companion flange.

    SST
    09330-00021  

  1. Using a socket wrench (32mm), install a new O-ring and a new companion flange lock nut.

    Torque:
    127 N*m{ 1299 kgf*cm , 94 ft.*lbf }



    F050151E01
  1. Using a chisel and hammer, stake the companion flange lock nut.



27. INSTALL TRANSFER CASE REAR OIL SEAL


    C180930
  1. Install the 2 output washers.

  1. Apply transfer oil to the spline area of the output shaft.



    C159303E01
  1. Using SST and a hammer, tap in a new oil seal until its surface is flush with the housing upper surface.

    SST
    09316-60011   (09316-00011)



28. INSTALL REAR OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY
  1. Install the companion flange onto the output shaft.



    C181035E01
  1. Using SST to hold the companion flange.

    SST
    09330-00021  

  1. Using a socket wrench (32mm), install a new O-ring and a new companion flange lock nut.

    Torque:
    127 N*m{ 1299 kgf*cm , 94 ft.*lbf }



    F050151E01
  1. Using a chisel and hammer, stake the companion flange lock nut.



29. INSTALL TRANSFER OIL PUMP PLATE OIL SEAL
SST
09950-60020   (09951-00680)
09950-70010   (09951-07100)


    C159806E01
  1. Using SST and a hammer, tap in a new oil seal until its surface is flush with the oil pump plate upper surface.

    SST
    09950-70010   (09951-07100)

    NOTICE:
    Be careful not to damage the oil pump plate.



30. INSTALL TRANSFER CASE STRAIGHT PIN


    C180853E01
  1. Install the 2 straight pins to the input shaft.



31. INSTALL TRANSFER OIL PUMP PLATE
  1. Apply transfer oil to a new O-ring, drive rotor and driven rotor.



    C180856
  1. Install the O-ring.



    C180850E01
  1. Install the drive rotors.



    C180851E01
  1. Install a new seal ring to the input shaft.



    C180849
  1. Install the oil pump plate with the 4 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



32. INSTALL TRANSFER CASE PLUG


    C180854
  1. Install the relief valve seat, ball and compression spring to the oil pump plate.

  1. Apply adhesive to the threads of the plug.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

  1. Using a 10 mm hexagon wrench, install the plug.

    Torque:
    29 N*m{ 300 kgf*cm , 22 ft.*lbf }



33. INSTALL HEAT INSULATOR BRACKET


    C180866
  1. Install the heat insulator bracket with the bolt.

    NOTICE:
    Position the bracket against the transfer case rib so that it will not rotate.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }