Home › Drivetrain ยท JF3A TRANSFER / 4WD / AWD › TRANSFER ASSEMBLY

TRANSFER ASSEMBLY > REASSEMBLY

for Preparation Click here


HINT:
Coat all of the sliding and rotating surfaces with gear oil before reassembly.



1. INSTALL REAR TRANSFER OUTPUT SHAFT


    C180911
  1. Install a new needle roller bearing.



    C180910
  1. Install the transfer drive sprocket sub-assembly.



    C180919E02
  1. Using SST and a press, press in a new bearing.

    SST
    09308-14010  
    09316-20011  

    NOTICE:
    Make sure the bearing is installed in the correct direction.



2. INSTALL FRONT DRIVE CLUTCH SLEEVE


    C180908
  1. Install the transfer clutch hub onto the front drive clutch sleeve.



    C180907E02
  1. Install the 3 shifting keys and 2 shifting key snap rings.
    Text in Illustration 
    *1
    Shifting Key Snap Ring
    *2
    Shifting Key

    NOTICE:
    Install the shifting key snap ring so that their end gaps are not in line.

  1. Apply transfer oil to the transfer synchronizer ring set.



    C180927E01
  1. Install the transfer synchronizer ring set.
    Text in Illustration 
    *1
    Transfer Synchronizer Ring Set

    NOTICE:
    Align the slots of the synchronizer outer with the inner rings.



    C180903E01
  1. Install the 2 transfer clutch hub bearings.



    C180920
  1. Install the front drive clutch sleeve with the synchronizer ring set, 2 shifting key snap rings, 3 shifting keys and transfer clutch hub onto the rear transfer output shaft.

    NOTICE:
    Align the cutouts in the transfer drive sprocket sub-assembly with the protrusions on the center synchronizer ring.



3. INSTALL CENTER DIFFERENTIAL CASE


    C270538
  1. Install the center differential case to the rear transfer output shaft.

  1. Install the straight pin to the rear transfer output shaft.



4. INSTALL NO. 1 TRANSFER OUTPUT SHAFT SPACER
  1. Apply transfer oil to a new seal ring.



    C173604E01
  1. Install the seal ring to the No. 1 transfer output shaft spacer.
    Text in Illustration 
    *1
    Seal Ring
    *2
    No. 1 Transfer Output Shaft Spacer



    C270539
  1. Align the straight pin with the straight pin groove of the No. 1 transfer output shaft spacer, and slide on the No. 1 transfer output shaft spacer.



    C270540
  1. Using a screwdriver and hammer, tap on the snap ring.



5. INSTALL TRANSFER INPUT SHAFT PLUG


    C180921E02
  1. Using SST and a hammer, tap in a new transfer input shaft plug as shown in the illustration.

    SST
    09950-70010   (09951-07150)
    09950-60010   (09951-00380)

    Drive in depth (A):
    1.0 to 1.8 mm (0.0394 to 0.0708 in.)

    NOTICE:
    Be careful not to damage or deform the transfer input shaft plug when tapping it.



6. INSTALL TRANSFER INPUT SHAFT BIMETAL FORMED BUSH


    C173632E02
  1. Using SST and a hammer, tap in a new transfer input shaft bimetal formed bush as shown in the illustration.

    SST
    09950-70010   (09951-07150)
    09950-60010   (09951-00600)

    Drive in depth (A):
    5.5 to 5.9 mm (0.217 to 0.232 in.)

    NOTICE:
    Be careful not to damage the transfer input shaft.



7. INSTALL TRANSFER INPUT SHAFT BEARING


    C173499E02
  1. Install the transfer low planetary gear bearing and transfer low planetary gear assembly to the transfer input shaft.

    NOTICE:
    1. Make sure that the transfer low planetary gear bearing is installed in the correct direction.
    2. Install the transfer low planetary gear bearing so that its temper color side faces the transfer low planetary gear assembly.

    Text in Illustration 
    *1
    Transfer Low Planetary Gear Bearing
    *2
    Transfer Low Planetary Gear Assembly
    *3
    Transfer Input Shaft
    *a
    Temper Color Side



    C173498E02
  1. Install the transfer low planetary gear bearing and a new transfer input shaft bearing to the transfer input shaft.
    Text in Illustration 
    *1
    Transfer Low Planetary Gear Bearing
    *2
    Transfer Input Shaft Bearing
    *3
    Transfer Low Planetary Gear Assembly
    *a
    Temper Color Side

    NOTICE:
    1. Make sure that the transfer input shaft bearing is installed in the correct direction.
    2. Make sure that the transfer low planetary gear bearing is installed in the correct direction.
    3. Install the transfer low planetary gear bearing so that its temper color side faces the transfer low planetary gear assembly.



    C180922E02
  1. Using SST and a press, press in the transfer input shaft bearing.

    SST
    09513-36040  
    09950-60020   (09951-00720)

    NOTICE:
    After press-fitting the transfer input shaft bearing to the transfer input shaft, check that the transfer input shaft bearing moves smoothly.



    C159629
  1. Select a transfer input shaft snap ring that allows for minimum axial play and install it to the transfer input shaft.

    Snap Ring Thickness:
    Mark
    Thickness
    C
    2.13 to 2.18 mm (0.0839 to 0.0858 in.)
    D
    2.18 to 2.23 mm (0.0859 to 0.0877 in.)
    E
    2.23 to 2.28 mm (0.0878 to 0.0897 in.)
    F
    2.28 to 2.33 mm (0.0898 to 0.0917 in.)
    G
    2.33 to 2.38 mm (0.0918 to 0.0937 in.)
    H
    2.38 to 2.43 mm (0.0938 to 0.0956 in.)
    J
    2.43 to 2.48 mm (0.0957 to 0.0976 in.)

  1. Using a snap ring expander, install the transfer input shaft snap ring.

    NOTICE:
    Make sure that the snap ring is firmly installed to the groove.



8. INSTALL NO. 1 TRANSFER INPUT SHAFT SEAL RING


    C162486
  1. Apply transfer oil to a new No. 1 transfer input shaft seal ring.

  1. Install the No. 1 transfer input shaft seal ring to the transfer input shaft.



9. INSTALL TRANSFER DRIVEN SPROCKET BEARING


    C180923E01
  1. Install a new transfer driven sprocket bearing to the front transfer case in the direction shown in the illustration.

    SST
    09950-60020   (09951-00790)
    09950-70010   (09951-07150)

    NOTICE:
    Make sure that the transfer driven sprocket bearing is installed in the correct direction.



10. INSTALL TRANSFER LOW PLANETARY RING GEAR


    C180891
  1. Install the transfer input shaft hole snap ring to the front transfer case.



    F043457E06
  1. Install the transfer low planetary ring gear to the front transfer case.
    Text in Illustration 
    *a
    Front

    NOTICE:
    Make sure to install the transfer low planetary ring gear in the correct direction.



    C173488
  1. Using a screwdriver, install the transfer low planetary ring gear hole snap ring.

    NOTICE:
    Make sure that the transfer low planetary ring gear hole snap ring is firmly installed to the groove.



11. INSTALL INPUT SHAFT ASSEMBLY


    C180888
  1. While expanding the transfer input shaft hole snap ring, install the input shaft assembly to the front transfer case.



    C180887
  1. Clean the threads of the 2 transfer case plugs and the front transfer case with non-residue solvent.

  1. Apply adhesive to the threads of the 2 transfer case plugs.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

    NOTICE:
    Install the transfer case plug within 3 minutes of application.

  1. Using a 14 mm hexagon wrench, install the 2 transfer case plugs.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }



12. INSTALL TRANSFER CASE MAGNET


    C180886
  1. Install the transfer case magnet.



13. INSTALL TRANSFER OIL SEPARATOR SUB-ASSEMBLY


    C180885E01
  1. Install a new O-ring.



    C180884
  1. Install the transfer oil separator sub-assembly with the 3 bolts.

    Torque:
    18 N*m{ 178 kgf*cm , 13 ft.*lbf }



14. INSTALL SIDE GEAR SHAFT HOLDER BEARING


    C273276E01
  1. Using SST and a press, install a new side gear shaft holder bearing.

    SST
    09214-60010  

    NOTICE:
    Press in the side gear shaft holder bearing until they fit to the edge.



15. INSTALL REAR OUTPUT SHAFT ASSEMBLY


    C180880
  1. Install the rear transfer output shaft snap ring to the rear transfer case.

  1. Fix the rear transfer case in a vise between aluminum plates.

    NOTICE:
    Do not overtighten the vise.



    C274079
  1. Install the rear output shaft assembly, drive chain and driven sprocket to the rear transfer case.

    NOTICE:
    Do not drop the front drive clutch sleeve or shifting keys.



    C270569
  1. Using a snap ring expander, install the rear transfer output shaft snap ring to the rear output shaft assembly.

    NOTICE:
    Make sure that the rear transfer output shaft snap ring is firmly installed to the groove.



16. INSTALL TRANSFER HIGH AND LOW CLUTCH SLEEVE


    C270568
  1. Install the transfer high and low clutch sleeve to the rear output shaft assembly.



17. INSTALL TRANSFER SHIFT ACTUATOR ASSEMBLY


    C160356E03
  1. Install a new O-ring to the transfer shift actuator assembly.



    C180872
  1. Set the No. 1 transfer gear shift fork and No. 2 transfer gear shift fork to the rear output shaft assembly. Then install the transfer shift actuator assembly to the rear transfer case with the 3 bolts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }



    C180870
  1. Install the 2 bolts.

    Torque:
    24 N*m{ 245 kgf*cm , 18 ft.*lbf }



    C270572
  1. Install the 3 transfer gear shift fork shaft snap rings into the transfer shift actuator assembly.



18. INSTALL TRANSFER OUTPUT SHAFT FRONT NEEDLE ROLLER BEARING


    C270567
  1. Install the spacer.

  1. Apply transfer oil to the transfer output shaft front needle roller bearing.



    C270566
  1. Install the transfer output shaft front needle roller bearing to the rear output shaft assembly.



19. INSTALL REAR TRANSFER CASE


    C160517E02
  1. Apply seal packing to the rear transfer case as shown in the illustration.

    Seal Packing:
    Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent

    Text in Illustration 
    *1
    Seal Packing

    NOTICE:
    If the removed rear transfer case will be reused: After removing the rear transfer case, perform the following before reinstalling it: 1) using a knife, cut off any old FIPG on the rear transfer case's contact surface, 2) clean off any remaining old FIPG from the rear transfer case's contact surface, and 3) reapply seal packing to the rear transfer case.



    C180868
  1. Install the rear transfer case with the 14 bolts.

    Torque:
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }

    NOTICE:
    Tighten the bolts of the rear transfer case within 10 minutes of applying the seal packing. The seal packing will dry very quickly.



20. INSTALL TRANSFER CASE PLUG
  1. Clean the threads of the transfer case plug and the front transfer case with non-residue solvent.



    C180867
  1. Apply adhesive to the threads of the transfer case plug.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

    NOTICE:
    Install the transfer case plug within 3 minutes of application.

  1. Using a 6 mm hexagon wrench, install the transfer case plug.

    Torque:
    39 N*m{ 400 kgf*cm , 29 ft.*lbf }



21. INSTALL NO. 1 TRANSFER CASE PLUG


    C180865E01
  1. Clean the threads of the No. 1 transfer case plug and the front transfer case with non-residue solvent.

  1. Apply adhesive to the threads of the No. 1 transfer case plug.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

    NOTICE:
    Install the No. 1 transfer case plug within 3 minutes of application.

  1. Install the pin, compression spring and No. 1 transfer case plug to the front transfer case.

    Torque:
    No. 1 Transfer Case Plug:
    19 N*m{ 190 kgf*cm , 14 ft.*lbf }

    Text in Illustration 
    *1
    No. 1 Transfer Case Plug
    *2
    Compression Spring
    *3
    Pin



22. INSTALL TRANSFER CASE FRONT OIL SEAL
  1. Apply transfer oil to the spline area of the driven sprocket.



    C159301E02
  1. Using SST and a hammer, tap in a new transfer case front oil seal as shown in the illustration.

    SST
    09316-60011   (09316-00011)

    Drive in depth (A):
    1.0 to 1.5 mm (0.0394 to 0.0590 in.)



23. INSTALL FRONT OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY
  1. Install the front output shaft companion flange sub-assembly onto the driven sprocket.



    C270542E01
  1. Use SST to hold the front output shaft companion flange sub-assembly.

    SST
    09330-00021  

  1. Using a 32 mm socket wrench, install a new O-ring and a new transfer output shaft nut.

    Torque:
    127 N*m{ 1299 kgf*cm , 94 ft.*lbf }

    Text in Illustration 
    *a
    Hold
    *b
    Turn



    F050151E03
  1. Using a chisel and hammer, stake the transfer output shaft nut.
    Text in Illustration 
    *a
    Correct
    *b
    Incorrect



24. INSTALL TRANSFER CASE REAR OIL SEAL


    C180930
  1. Install the 2 output washers.

  1. Apply transfer oil to the spline area of the rear transfer output shaft.



    C159303E01
  1. Using SST and a hammer, tap in a new transfer case rear oil seal until its surface is flush with the housing upper surface.

    SST
    09316-60011   (09316-00011)



25. INSTALL REAR OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY
  1. Install the rear output shaft companion flange sub-assembly onto the rear transfer output shaft.



    C270543E01
  1. Use SST to hold the rear output shaft companion flange sub-assembly.

    SST
    09330-00021  

  1. Using a 32 mm socket wrench, install a new O-ring and a new transfer output shaft nut.

    Torque:
    127 N*m{ 1299 kgf*cm , 94 ft.*lbf }

    Text in Illustration 
    *a
    Hold
    *b
    Turn



    F050151E03
  1. Using a chisel and hammer, stake the transfer output shaft nut.
    Text in Illustration 
    *a
    Correct
    *b
    Incorrect



26. INSTALL TRANSFER OIL PUMP PLATE OIL SEAL


    C159806E02
  1. Using SST and a hammer, tap in a new transfer oil pump plate oil seal as shown in the illustration.

    SST
    09950-70010   (09951-07100)
    09950-60010   (09951-00630)

    Drive in depth (A):
    0.5 mm or less (0.0196 in. or less)

    NOTICE:
    Be careful not to damage the transfer oil pump plate.



27. INSTALL TRANSFER CASE STRAIGHT PIN


    C180853E02
  1. Install the 2 transfer case straight pins to the transfer input shaft.



28. INSTALL TRANSFER OIL PUMP PLATE


    C180856
  1. Apply transfer oil to a new O-ring, transfer oil pump drive rotor, transfer oil pump driven rotor and a new transfer oil seal ring.

  1. Install the O-ring.



    C180850E02
  1. Install the transfer oil pump drive rotor and transfer oil pump driven rotor.
    Text in Illustration 
    *1
    Transfer Oil Pump Drive Rotor
    *2
    Transfer Oil Pump Driven Rotor



    C180851
  1. Install the transfer oil seal ring to the transfer input shaft.



    C180849
  1. Install the transfer oil pump plate with the 4 bolts.

    Torque:
    12 N*m{ 117 kgf*cm , 8 ft.*lbf }



29. INSTALL TRANSFER CASE PLUG


    C180854E01
  1. Clean the threads of the transfer case plug and the transfer oil pump plate with non-residue solvent.
    Text in Illustration 
    *1
    Transfer Case Plug
    *2
    Compression Spring
    *3
    Ball
    *4
    Relief Valve Seat

  1. Apply adhesive to the threads of the transfer case plug.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

  1. Install the relief valve seat, ball and compression spring to the transfer oil pump plate.

  1. Using a 10 mm hexagon wrench, install the transfer case plug.

    Torque:
    29 N*m{ 300 kgf*cm , 22 ft.*lbf }



30. INSTALL HEAT INSULATOR BRACKET


    C180866
  1. Install the heat insulator bracket with the bolt.

    NOTICE:
    Position the heat insulator bracket against the front transfer case rib so that it will not rotate.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }