Home › Engine / Hybrid System › 3UR-FE EMISSION CONTROL › CANISTER

CANISTER > REMOVAL

for Preparation Click here



1. DISCONNECT FUEL TANK VENT HOSE SUB-ASSEMBLY


A184908
  1. Pull up the retainer and disconnect the fuel tank vent hose sub-assembly.

    NOTICE:
    1. Do not use any tools in this procedure.
    2. Check for any dirt and foreign matter contamination in the valve and around the connector. Clean if necessary. Foreign matter may damage the O-rings or cause leaks in the seal between the valve and connector.

  1. Remove the bolt.



2. DISCONNECT NO. 1 CHARCOAL CANISTER OUTLET HOSE


A309515
  1. Disconnect the No. 1 charcoal canister outlet hose from the fuel tank filler pipe sub-assembly.



3. REMOVE CHARCOAL CANISTER ASSEMBLY


A184910
  1. Slide the clamp and disconnect the charcoal canister outlet hose from the No. 3 fuel tank to canister tube.



    A309517
  1. Remove the 3 bolts and charcoal canister assembly.



4. REMOVE FUEL TANK VENT HOSE SUB-ASSEMBLY


A309518E01
  1. Push the fuel tank vent hose sub-assembly firmly toward the canister side.
    Text in Illustration 
    *a
    Charcoal Canister Assembly Side

  1. Pinch the fuel tank vent hose sub-assembly (portion A) as shown in the illustration.

  1. Pull out the fuel tank vent hose sub-assembly.

    NOTICE:
    1. Do not use any tools in this procedure.
    2. Check for any dirt and foreign matter contamination in the charcoal canister assembly and around the hose. Clean if necessary. Foreign matter may damage the O-rings or cause leaks in the seal between the charcoal canister assembly and fuel tank vent hose sub-assembly.



5. REMOVE CHARCOAL CANISTER FILTER SUB-ASSEMBLY


A309519E01
  1. Disconnect the No. 2 canister outlet hose sub-assembly.
    Text in Illustration 
    *a
    Charcoal Canister Assembly Side

    1. Push the No. 2 canister outlet hose sub-assembly firmly toward the canister side.

    2. Pinch the No. 2 canister outlet hose sub-assembly (portion A) as shown in the illustration.

    3. Pull out the No. 2 canister outlet hose sub-assembly.

      NOTICE:
      1. Do not use any tools in this procedure.
      2. Check for any dirt and foreign matter contamination in the charcoal canister assembly and around the hose. Clean if necessary. Foreign matter may damage the O-rings or cause leaks in the seal between the charcoal canister assembly and No. 2 canister outlet hose sub-assembly.

  1. Detach the claw and remove the charcoal canister filter sub-assembly.

  1. Disconnect the charcoal canister outlet hose from hose clamp.



    A309520
  1. Remove the hose clamp.



6. REMOVE NO. 1 CHARCOAL CANISTER OUTLET HOSE


A184916
  1. Remove the No. 1 charcoal canister outlet hose.



7. REMOVE CHARCOAL CANISTER OUTLET HOSE


A309523
  1. Slide the clamp and remove the charcoal canister outlet hose.



8. REMOVE CHARCOAL CANISTER BASE BRACKET
  1. Detach the claw to remove the charcoal canister base bracket.



9. REMOVE CHARCOAL CANISTER SUPPORT BRACKET
  1. Detach the claw to remove the charcoal canister support bracket.



10. REMOVE CANISTER PUMP MODULE
  1. Before removing the canister pump module, clean the charcoal canister assembly by blowing air into it to ensure that the charcoal canister assembly is free of foreign matter.

    NOTICE:
    1. Make sure to clean the charcoal canister assembly using only air.
    2. Do not use gasoline, thinners or solvents.



    A263349
  1. While disengaging the 2 claws as shown in the illustration, push the canister pump module upwards using a screwdriver to remove it.



  1. Check if the charcoal canister assembly contains foreign matter such as mud or water.



      A263350
    1. Visually check that the inside of the charcoal canister assembly is free of foreign matter.

    2. Hold the charcoal canister assembly upside down to make sure that the charcoal canister assembly is free of foreign matter.
      If the charcoal canister assembly contains foreign matter, replace the charcoal canister assembly.