Home › General › SPECIFICATIONS › 3UR-FE ENGINE CONTROL

3UR-FE ENGINE CONTROL > SERVICE DATA



MAF meter:

Tester Connection
Condition
Specified Condition
4 (THA) - 5 (E2)
-20°C (-4°F)
12.5 k to 16.9 kΩ
20°C (68°F)
2.19 k to 2.67 kΩ
60°C (140°F)
0.50 k to 0.68 kΩ


Camshaft timing oil control valve:

Tester Connection
Condition
Specified Condition
1 - 2
20°C (68°F)
6.9 to 7.9 Ω


Engine coolant temperature sensor:

Tester Connection
Condition
Specified Condition
1 - 2
Approx. 20°C (68°F)
2.32 k to 2.59 kΩ
Approx. 80°C (176°F)
0.310 k to 0.326 kΩ


Throttle W/motor body:

Tester Connection
Condition
Specified Condition
1 (M-) - 2 (M+)
20°C (68°F)
0.3 to 100 Ω


Accelerator pedal:

Tester display
Accelerator pedal released
Accelerator pedal depressed
Accelerator position No. 1
0.5 to 1.1 V
2.6 to 4.5 V
Accelerator position No. 2
1.2 to 2.0 V
3.4 to 5.3 V


Knock sensor:

Tester Connection
Condition
Specified Condition
1 - 2
20°C (68°F)
120 to 280 kΩ


Air fuel ration sensor:

Tester Connection
Condition
Specified Condition
1 (HA1A) - 2 (+B)
(for Bank 1)
20°C (68°F)
1.8 to 3.4 Ω
1 (HA2A) - 2 (+B)
(for Bank 2)


Heated oxygen sensor:

Tester Connection
Condition
Specified Condition
1 (HT1B) - 2 (+B)
(for Bank 1)
20°C (68°F)
11 to 16 Ω
1 (HT2B) - 2 (+B)
(for Bank 2)


IG2 relay:

Tester Connection
Condition
Specified Condition
IG2 MAIN fuse
Always
Below 1 Ω
1C-1 - 1B-8
When battery voltage is not applied to terminals 1B-6 and 1B-7
10 kΩ or higher
When battery voltage is applied to terminals 1B- 6 and 1B-7
Below 1 Ω


EFI relay:

Tester Connection
Condition
Specified Condition
EFI No. 1 fuse
Always
Below 1 Ω
1C-1 - 1B-4
When battery voltage is not applied to terminals 1B-2 and 1B-3)
10 kΩ or higher
When battery voltage is applied to terminals 1B- 2 and 1B-3)
Below 1 Ω


Circuit opening relay:

Tester Connection
Condition
Specified Condition
3 - 5
When battery voltage is not applied to terminals 1 and 2
10 kΩ or higher
When battery voltage is applied to terminals 1 and 2
Below 1 Ω


Fuel pump relay:

Tester Connection
Condition
Specified Condition
3 - 5
When battery voltage is not applied to terminals 1 and 2
10 kΩ or higher
When battery voltage is applied to terminals 1 and 2
Below 1 Ω


A/F sensor heater relay:

Tester Connection
Condition
Specified Condition
A/F fuse
Always
Below 1 Ω
1C-1 - 1A-4
When battery voltage is not applied to terminals 1A-2 and 1A-3
10 kΩ or higher
When battery voltage is applied to terminals 1A- 2 and 1A-3
Below 1 Ω

Spark Plug 
Recommended spark plug
DENSO made: SK20HR11
Correct electrode gap for new spark plug
1.0 to 1.1 mm (0.0394 to 0.0433 in.)
Maximum electrode gap for used spark plug
1.3 mm (0.0512 in.)
Standard insulation resistance
10 MΩ or more