Home › Suspension › ALIGNMENT / HANDLING DIAGNOSIS › REAR WHEEL ALIGNMENT

REAR WHEEL ALIGNMENT > ADJUSTMENT

for Preparation Click here


NOTICE:
For vehicles equipped with VSC, if the wheel alignment has been adjusted, and if suspension or underbody components have been removed/installed or replaced, be sure to perform the following initialization procedure in order for the system to function normally:
  1. Disconnect the negative battery terminal for more than 2 seconds.
  2. Reconnect the negative battery terminal.



1. INSPECT TIRE
  1. Check the tires for wear and proper inflation pressure.

    Standard Cold Tire Inflation Pressure:
    Tire Size
    Front
    kPa (kgf/cm2, psi)
    Rear
    kPa (kgf/cm2, psi)
    Spare
    kPa (kgf/cm2, psi)
    P275/65R18
    230 (2.3, 33)
    230 (2.3, 33)
    230 (2.3, 33)
    P275/55R20
    210 (2.1, 30)
    240 (2.4, 35)
    240 (2.4, 35)



    R003031
  1. Using a dial indicator, check the tire runout.

    Tire runout:
    3.0 mm (0.118 in.) or less



2. MEASURE VEHICLE HEIGHT

NOTICE:
Before inspecting the wheel alignment, adjust the vehicle height to the specification.



    C180789E01
  1. Press down on the vehicle several times to stabilize the suspension, and then measure the vehicle height.

    Standard Vehicle Height (Unloaded Vehicle):

    Vehicle Model
    Rear Suspension Type
    Tire Size
    Front A - B
    Rear C - D
    USK60L-GKTSKV
    Coil
    P275/65R18 8JJ
    107.3 mm (4.22 in.)
    28.4 mm (1.12 in.)
    P275/55R20 8JJ
    107.5 mm (4.23 in.)
    28.6 mm (1.13 in.)
    Air
    P275/65R18 8JJ
    106.1 mm (4.18 in.)
    39.1 mm (1.54 in.)
    P275/55R20 8JJ
    106.2 mm (4.18 in.)
    39.3 mm (1.55 in.)
    USK60L-GKTLKV
    Coil
    P275/65R18 8JJ
    108.7 mm (4.28 in.)
    31.6 mm (1.24 in.)
    P275/55R20 8JJ
    108.8 mm (4.28 in.)
    31.8 mm (1.25 in.)
    Air
    P275/65R18 8JJ
    107.7 mm (4.24 in.)
    39.2 mm (1.54 in.)
    P275/55R20 8JJ
    107.9 mm (4.25 in.)
    39.5 mm (1.56 in.)
    USK60L-GKTZKV
    Air + AVS
    P275/55R20 8JJ
    108.6 mm (4.28 in.)
    39.5 mm (1.56 in.)
    USK65L-GKTSKV
    Coil
    P275/65R18 8JJ
    102.9 mm (4.05 in.)
    24.4 mm (0.96 in.)
    P275/55R20 8JJ
    102.9 mm (4.05 in.)
    24.4 mm (0.96 in.)
    Air
    P275/65R18 8JJ
    101.7 mm (4.00 in.)
    34.1 mm (1.34 in.)
    P275/55R20 8JJ
    101.8 mm (4.01 in.)
    34.1 mm (1.34 in.)
    USK65L-GKTLKV
    Coil
    P275/65R18 8JJ
    104.0 mm (4.09 in.)
    26.8 mm (1.06 in.)
    P275/55R20 8JJ
    104.0 mm (4.09 in.)
    26.8 mm (1.06 in.)
    Air
    P275/65R18 8JJ
    103.1 mm (4.06 in.)
    34.2 mm (1.35 in.)
    P275/55R20 8JJ
    103.1 mm (4.06 in.)
    34.3 mm (1.35 in.)
    USK65L-GKTZKV
    Air + AVS
    P275/55R20 8JJ
    104.2 mm (4.10 in.)
    34.4 mm (1.35 in.)

    1. Measuring points

    A:
    Ground clearance of the front drive shaft center

    B:
    Ground clearance of the front adjusting cam bolt center

    C:
    Ground clearance of the rear drive shaft center

    D:
    Ground clearance of the rear lower arm No. 1 adjusting cam bolt center

    If the vehicle height is not as specified, adjust the height by pressing down on the vehicle several times to stabilize the suspension.



3. INSPECT CAMBER


C107736E01
  1. Install a camber-caster-kingpin gauge or put the wheels on a wheel alignment tester.

  1. Inspect the camber.

    Standard Camber Inclination (Unloaded Vehicle):
    Drive Type
    Rear Suspension Type
    Camber Inclination
    2WD
    Coil
    -1°25' +/-45'
    (-1.42° +/-0.75°)
    2WD
    Air
    -1°41' +/-45'
    (-1.68° +/-0.75°)
    4WD
    Coil
    -1°17' +/-45'
    (-1.28° +/-0.75°)
    4WD
    Air
    -1°33' +/-45'
    (-1.55° +/-0.75°)

    1. If the measured value is not within the specified range, inspect the suspension parts for damage and wear. Replace parts as necessary because camber cannot be properly adjusted with any damaged or worn parts.



4. ADJUST CAMBER


C180800
  1. Loosen the camber adjust cam nut.

  1. Rotate the camber adjust cam on the vehicle side of No. 2 lower arm to adjust camber.

    Standard Camber Inclination (Unloaded Vehicle):
    Drive Type
    Rear Suspension Type
    Camber Inclination
    2WD
    Coil
    -1°25' +/-45'
    (-1.42° +/-0.75°)
    2WD
    Air
    -1°41' +/-45'
    (-1.68° +/-0.75°)
    4WD
    Coil
    -1°17' +/-45'
    (-1.28° +/-0.75°)
    4WD
    Air
    -1°33' +/-45'
    (-1.55° +/-0.75°)

  1. Tighten the nut.

    Torque:
    250 N*m{ 2549 kgf*cm , 185 ft.*lbf }



5. INSPECT TOE-IN


SA03213E04

Standard toe-in (Unloaded Vehicle):
Drive Type
Rear Suspension Type
Specified Condition
2WD
Coil
A + B: -0°02' +/-4' (-0.03° +/-0.07°)
C - D: -1.0 +/-2 mm (-0.04 +/-0.08 in.)
2WD
Air
A + B: -0°01' +/-4' (-0.02°+/-0.07°)
C - D: -0.3 +/-2 mm (-0.01 +/-0.08 in.)
4WD
Coil
A + B: -0°03' +/-4' (-0.05°+/-0.07°)
C - D: -1.4 +/-2 mm (-0.06 +/-0.08 in.)
4WD
Air
A + B: -0°02' +/-4' (-0.03°+/-0.07°)
C - D: -0.7 +/-2 mm (-0.03 +/-0.08 in.)

  1. If the toe-in is not within the specified range, inspect the suspension parts and replace if necessary.


6. ADJUST TOE-IN


C180801
  1. Loosen the toe adjust cam bolt.

  1. Rotate the toe adjust plate on the vehicle side of lower arm No. 2 to adjust toe-in.

    Standard toe-in (Unloaded Vehicle):
    Drive Type
    Rear Suspension Type
    Specified Condition
    2WD
    Coil
    A + B: -0°02' +/-4' (-0.03° +/-0.07°)
    C - D: -1.0 +/-2 mm (-0.04 +/- 0.08 in.)
    2WD
    Air
    A + B: -0°01' +/-4' (-0.02° +/-0.07°)
    C - D: -0.3 +/-2 mm (-0.01 +/- 0.08 in.)
    4WD
    Coil
    A + B: -0°03' +/-4' (-0.05°+/-0.07°)
    C - D: -1.4 +/-2 mm (-0.06 +/-0.08 in.)
    4WD
    Air
    A + B: -0°02' +/-4' (-0.03°+/-0.07°)
    C - D: -0.7 +/-2 mm (-0.03 +/-0.08 in.)

  1. Tighten the bolt.

    Torque:
    120 N*m{ 1224 kgf*cm , 89 ft.*lbf }



7. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
Disconnect the negative battery terminal for more than 2 seconds.



8. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



9. PERFORM YAW RATE SENSOR ZERO POINT CALIBRATION
(Click here)


10. CHECK STEERING ANGLE SENSOR ZERO POINT CALIBRATION
(Click here)