Home › Vehicle Interior › SEAT BELT › FRONT SEAT OUTER BELT ASSEMBLY

FRONT SEAT OUTER BELT ASSEMBLY > INSTALLATION

for Preparation Click here


HINT:
  1. Use the same procedure for the LH side and RH side.
  2. The procedure listed below is for the RH side.



1. INSTALL FRONT SHOULDER BELT ANCHOR ADJUSTER ASSEMBLY


    B194071
  1. Align the front shoulder belt anchor adjuster positioning claw with the hole, and install the front shoulder belt anchor adjuster with the 2 bolts.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



2. INSTALL FRONT SEAT OUTER BELT ASSEMBLY


    B194070E01
  1. Align the claws on the body with the front seat outer belt retractor positioning holes.

  1. Install the front seat outer belt with the 2 bolts.

    HINT:
    First install bolt A, and then install bolt B.

    1. for Bolt A

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    1. for Bolt B

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B194069E01
  1. Connect the pretensioner connector as shown in the illustration.



    B194067
  1. Install the shoulder anchor to the shoulder belt anchor adjuster with the nut.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



3. INSTALL CENTER PILLAR GARNISH RH
  1. Pass the front seat outer belt floor anchor through the center pillar garnish.

  1. Attach the clip and guide to install the center pillar garnish.

  1. Install the bolt.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }

  1. Install the assist grip with the 2 bolts.

    Torque:
    9.7 N*m{ 99 kgf*cm , 86 in.*lbf }



  1. Attach the 2 claws to install the 2 assist grip plugs.


    B193061



4. INSTALL LOWER CENTER PILLAR GARNISH RH


    B190125
  1. Attach the 7 clips and 2 claws to install the center pillar garnish.



    B190129
  1. Install the front seat outer belt assembly RH with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B190128
  1. Attach the 3 claws to install the cover.



5. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH


    B190154E01
  1. Align the location mark with the paint mark first, and install the rear door opening trim weatherstrip, as shown in the illustration.
    Paint Mark 
    Area
    Color
    RH side
    Pink
    LH side
    Purple



6. INSTALL REAR DOOR SCUFF PLATE RH


    B186666
  1. Attach the 2 claws and 5 clips to install the rear door scuff plate.

  1. Install the 2 bolts.



    B186665
  1. Attach the 6 claws, 5 clips and 2 guides to install the rear door scuff plate.

  1. Install the bolt.



7. INSTALL REAR FLOOR STEP NO. 1 COVER


    B191404
  1. Attach the 2 claws to install the rear floor step No. 1 cover.



8. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH


    B190153E01
  1. Align the location mark with the paint mark first, and install the front door opening trim weatherstrip, as shown in the illustration.
    Paint Mark 
    Area
    Color
    RH side
    White
    LH side
    Yellow



9. INSTALL FRONT DOOR SCUFF PLATE RH


B190151
  1. Attach the 9 claws to install the scuff plate.



10. INSTALL FRONT SEAT ASSEMBLY RH (for Manual Seat)
  1. Install the front seat assembly (Click here).



11. INSTALL FRONT SEAT ASSEMBLY RH (for Power Seat)
  1. Install the front seat assembly (Click here).



12. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable some systems need to be initialized after the cable is reconnected (Click here).