Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM

DTC    B2799    Engine Immobiliser System Malfunction

for Preparation Click here


DESCRIPTION

The ECM stores this DTC when the communication line between the ECM and transponder key ECU assembly is malfunctioning or the communication ID of the ECM and transponder key ECU assembly do not match.

DTC No.
DTC Detection Condition
Trouble Area
DTC Output Confirmation Operation
B2799
One of the following conditions is met:
  1. Error in communication between ECM and transponder key ECU assembly.
  2. Error in communication lines.
  3. Communication ID is different during communication between ECM and transponder key ECU assembly.
  1. Harness or connector
  2. Transponder key ECU assembly
  3. ECM
  1. Start the engine and wait 10 seconds.*1
  2. After disconnecting and reconnecting the cable to the negative (-) battery terminal, turn the ignition switch to ON and wait 10 seconds.*2
    *1: Communication starts within 3 seconds of starting the engine. If verification fails, this DTC is stored 6 seconds after communication has completed.
    *2: Communication starts within 3 seconds of turning the ignition switch to ON. If verification fails, this DTC is stored 6 seconds after communication has completed.

Vehicle Condition and Fail-safe Operation when Malfunction Detected 
Vehicle Condition when Malfunction Detected
Fail-safe Operation when Malfunction Detected
Engine cannot be started
-

Related Data List and Active Test 
DTC No.
Data List and Active Test
B2799
-

WIRING DIAGRAM


B365295E04


INSPECTION PROCEDURE

NOTICE:
  1. If the transponder key ECU assembly or ECM is replaced, refer to Service Bulletin.
  2. After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".
  3. When using the GTS with the vehicle ignition switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Immobiliser. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

HINT:
If transponder key ECU assembly DTCs are output simultaneously, troubleshoot the transponder key ECU assembly DTCs first.

1.CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


2.CHECK FOR DTC
  1. Start the engine.

  1. Check for DTCs (Click here).

    HINT:
    Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.

    OK:
    DTC B2799 is not output.

    Result 
    Result
    Proceed to
    OK
    A
    NG (DTC B2799 is output)
    B
    NG (Other DTCs are output)
    C



B
Go to step 3

C
GO TO DIAGNOSTIC TROUBLE CODE CHART (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)  

3.REGISTER ECU COMMUNICATION ID
  1. Reregister the ECU communication ID.

    HINT:
    Refer to Service Bulletin.


NEXT


4.CHECK WHETHER ENGINE STARTS
  1. Using a registered key, turn the ignition switch to ON.

  1. Check that the engine starts 5 seconds after the ignition switch was turned to ON.

    OK:
    Engine starts normally.



NG
Go to step 5
OK

END (ECU COMMUNICATION ID REGISTRATION WAS DEFECTIVE) 

5.REPLACE ECM
  1. Temporarily replace the ECM with a new one or known good one (Click here).


NEXT


6.CHECK WHETHER ENGINE STARTS
  1. Using a registered key, turn the ignition switch to ON.

  1. Check that the engine starts 5 seconds after the ignition switch was turned to ON.

    OK:
    Engine starts normally.



NG
Go to step 7
OK

END (ECM WAS DEFECTIVE) 

7.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - ECM)
  1. Disconnect the H32 transponder key ECU assembly connector.

  1. Disconnect the A27 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H32-12 (EFII) - A27-29 (IMO)
    Always
    Below 1 Ω
    H32-13 (EFIO) - A27-40 (IMI)
    Always
    Below 1 Ω
    H32-12 (EFII) - Body ground
    Always
    10 kΩ or higher
    H32-13 (EFIO) - Body ground
    Always
    10 kΩ or higher
    A27-29 (IMO) - Body ground
    Always
    10 kΩ or higher
    A27-40 (IMI) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY