Home › Engine / Hybrid System › 3UR-FE STARTING › STARTER

STARTER > INSPECTION

for Preparation Click here



1. INSPECT STARTER ASSEMBLY

CAUTION:
As a large electric current passes through the cable during this inspection, a thick cable must be used. Otherwise, the cable may become hot and cause injury.

NOTICE:
These tests must be performed within 3 to 5 seconds to avoid burning out the coil.



  1. Perform a pull-in test.

    1. Remove the nut, and then disconnect the field coil lead wire from terminal C.



    2. A258308E02
    3. Connect the battery to the magnet starter switch as shown in the illustration. Then check that the clutch pinion gear moves outward.
      If the clutch pinion gear does not move outward, replace the magnet starter switch assembly.



  1. Perform a holding test.



      A258309E01
    1. When the battery is connected as above with the clutch pinion gear out, disconnect the negative (-) lead from terminal C. Check that the pinion gear remains out.
      If the clutch pinion gear moves inward, replace the magnet starter switch assembly.



  1. Inspect the clutch pinion gear return.



      A258310
    1. Disconnect the negative (-) lead from the starter body. Check that the clutch pinion gear returns inward.
      If the clutch pinion gear does not return inward, replace the magnet starter switch assembly.



  1. Perform an operation test without load.

    1. Connect the field coil wire to terminal C with the nut. Make sure that the lead is not grounded.

      Torque:
      10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    2. Mount the starter in a vise between aluminum plates.



    3. A258311E02
    4. Connect the battery and an ammeter to the starter as shown in the illustration.

    5. Check that the starter rotates smoothly and steadily while the pinion gear is moving outward. Then measure the current.

      Standard current:
      150 A or less at 11.5 V

      If the result is not as specified, inspect the starter assembly.

      HINT:
      Inspect the starter brush holder assembly, starter yoke assembly and starter armature assembly. If there is a malfunction, replace the part and perform this test again.



2. INSPECT STARTER ARMATURE ASSEMBLY
  1. Check the surface of the commutator for dirt and burns.
    If the surface is dirty or burnt, correct it with sandpaper (No. 400) or a lathe.
    If necessary, replace the starter armature assembly.



  1. Inspect the commutator for an open circuit.



      A215965E01
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Segment - Segment
      Always
      Below 1 Ω

      If the result is not as specified, replace the starter armature assembly.



  1. Inspect the commutator for a short circuit.



      A215966E01
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Segment - Coil core
      Always
      10 kΩ or higher

      If the result is not as specified, replace the starter armature assembly.



    A215958
  1. Using a vernier caliper, measure the commutator diameter.

    Standard diameter:
    29.0 mm (1.14 in.)

    Minimum diameter:
    28.0 mm (1.10 in.)

    HINT:
    Be sure to measure the commutator diameter at the ridges.

    If the diameter is less than the minimum, replace the starter armature assembly.



  1. Check the commutator circle runout.



      A215967
    1. Place the armature shaft on V-blocks.

    2. Using a dial indicator, measure the commutator runout.

      Maximum commutator runout:
      0.05 mm (0.00197 in.)

      If the commutator runout is more than the maximum, replace the starter armature assembly.



    A062965E01
  1. Measure the undercut depth of the commutator.

    Standard undercut depth:
    0.4 mm (0.0157 in.)

    Minimum undercut depth:
    0.2 mm (0.00787 in.)

    HINT:
    Be sure to measure the commutator undercut depth at a cutout.

    If the undercut depth is less than the minimum, correct it with a hacksaw blade.



3. INSPECT STARTER BRUSH HOLDER ASSEMBLY


    A215975
  1. Using a vernier caliper, measure the brush length.

    Standard length:
    14.4 mm (0.567 in.)

    Minimum length:
    9.0 mm (0.354 in.)

    HINT:
    Be sure to measure the brush lengths at the protrusions.

    If the length is less than the minimum, replace the starter brush holder assembly.



  1. Inspect the load of the brush spring.



      ST00019E10
    1. Take the pull scale reading immediately after the brush spring separates from the brush.

      Standard spring load:
      22 to 27 N (2 to 3 kgf, 5.0 to 6.1 lbf)

      Minimum spring load:
      14 N (1 kgf, 3.1 lbf)

      If the load is less than the minimum, replace the starter brush holder assembly.



4. INSPECT STARTER CENTER BEARING CLUTCH SUB-ASSEMBLY
  1. Check the gear teeth on the planetary gears, and the internal gear and pinion gear of the starter center bearing clutch for wear or damage.
    If any of the gears is damaged, replace the gear or starter center bearing clutch sub-assembly.



    A215964E01
  1. Hold the starter clutch, rotate the pinion gear clockwise and check that it turns freely. Try to rotate the pinion gear counterclockwise and check that it locks.
    If the result is not as specified, replace the starter center bearing clutch sub-assembly.



5. INSPECT MAGNET STARTER SWITCH ASSEMBLY


  1. Check if the pull-in coil has an open circuit.



      A162877E01
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Terminals 50 - Terminal C
      Always
      Below 1 Ω

      If the result is not as specified, replace the magnet starter switch assembly.



  1. Check if the holding coil has an open circuit.



      A162878E01
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Terminal 50 - Switch body
      Always
      Below 2 Ω

      If the result is not as specified, replace the magnet starter switch assembly.